Advertisement
DO NOT modify or change the sander motor for one with a different rating.
#
DO NOT turn the sander on until work table is clear of all objects, wood scraps etc.
#
DO NOT touch the sanding disc whilst operating, or whilst sander is plugged into the mains power.
#
DO NOT switch the sander on while the workpiece is in contact with the sanding disc.
#
DO NOT operate the sander if any parts are damaged or missing as this may cause failure or possible personal injury.
#
DO NOT allow children or untrained persons to operate the sander. Keep them away from the work area.
#
DO NOT use the sander for any purpose other than wood finishing.
#
When not in use, unplug from the mains power supply and store in a childproof location.
!
2. TECHNICAL SPECIFICATION
Model . . . . . . . . . . . . . . . . .SM31.V3
Disc Diameter
. . . . . . . . . .Ø305mm
Disc Speed . . . . . . . . . . . . .1450rpm
Table . . . . . . . . . . . . . .156 x 438mm
3. ASSEMBLY
3.1.
Unpack the sander and check contents against the list below. If there are any damaged or missing parts contact your supplier immediately.
Contents:
• Sander Assembly
3.2.
Remove various screws (fig.1.parts1-4) from the sander assembly, fit table (A) in position and retain by replacing screws. The table should
always have at least 1.6mm clearance from the sanding disc, adjustment can be made by loosening the six cross head bolts in the face of
the table top.
3.3.
If a dust extraction system is available, connect it to the extraction port (diameter 52mm).
3.4.
The mitre gauge, when required, locates in the table groove.
WARNING! Before use, the machine must be positioned on a stable, fireproof bench or table which is strong enough to take the
"
weight of the machine and the workpiece. The sander is supplied with rubber feet, alternatively it can be bolted to a work surface.
Failure to comply with this instruction could result in severe personal injury.
4. OPERATING INSTRUCTIONS
4.1.
Ensure that you have read, understand and apply the safety
instructions in Section 1.
WARNING! Before each use rotate the sanding disc by hand to
"
check it is undamaged and secure. Remove adjusting keys and
wrenches before turning the machine on.
4.2.
Table adjustment
4.2.1. The table is adjustable through 45
lever handles (fig1.3.) - both right hand thread, adjusting the table to
the required angle and then fully tightening both handles.
4.3.
Mitre gauge adjustment
4.3.1. The gauge is adjustable through ±45
screw, adjusting to required angle and tightening the thumb screw.
4.4.
Operating sander
4.4.1. Feed workpiece carefully into the sanding disc, work methodically
and DO NOT force the sander to remove material faster than it was
designed for. Hold workpiece with both hands and ensure that they
are not in a position where they could slip up against the sanding
disc.
4.4.2. Ensure large workpieces are supported at table height.
4.4.3. Turn sander off and make sure sanding disc is stationary before
clearing scrap pieces from the table.
4. OPERATING INSTRUCTIONS
5. MAINTENANCE
5.1.
The sander is maintenance free and only requires cleaning using a vacuum cleaner and brush.
5.2.
Occasionally check sander over for loose fittings and to ensure sanding disc is secure.
DISC SANDER 305mm
Model: SM31.V3
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37/EC Machinery Directive
93/68/EEC Marking Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
Table Tilt . . . . . . . . . . . . . . . . . . .45
Dust Extraction Port . . . . . . .Ø52mm
Motor . . . . . . . . . . . . . .750W - 230V
Weight . . . . . . . . . . . . . . . . . .29.5kg
• Table
• Mitre Gauge
by slackening the two locking
O
by slackening the thumb
O
Declaration of Conformity
in conformity with the following standards and directives
Signed by Steve Buckle
The construction file for this product is held by the Manufacturer and may be inspected on request by contacting
Jack Sealey Ltd.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
• Hex. Key
fig.1
We, the sole importer into the UK, declare that the product listed here
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery Ltd.
01284 757500
01284 703534
O
Date 29th June 2006
www.sealey.co.uk
Web
sales@sealey.co.uk
email
SM31.V3 - 1 - 290606
is
Advertisement
