Advertisement
Timer ON - Timer OFF
To set when you want the unit to turn On at the end of a selected
time period, use the button labeled "Time- ON" on the remote
controller. Press this button to make the clock icon disappear,
replaced with the word "ON" (blinking). Press "
buttons to adjust timer setting 1 minute at a time. Press and hold
▲
▼
"
" or "
" button to set timer more quickly. Press"Timer- ON"
button again to confirm setting, and the word "ON" stops blinking.
To cancel, press the "Timer OFF".
NOTE: Under Timer On and Off status, you can set T- ON
and T- OFF simultaneously. Before setting timer, be sure to
set clock to correct time.
CLOCK SETTING
Press this button to set clock time. The Clock icon on remote
controller blinks. Within 5 seconds, press "
set clock time. With each press of the "
clock time increases or decreases by 1 minute. To quickly adjust
the time setting, press and hold "
Release the button when you have reached the desired time setting.
Press the "CLOCK" button to confirm the time, and clock icon
stops blinking.
NOTE: Clock time adopts 24- hour mode. A 12- hour format is
not available.
SLEEP:
The unit automatically adjusts room temperature during your sleep
time. This slight change in temperature will not affect your comfort
level due to the natural effects that sleeping has on the body, however
it saves on energy consumption and lowers your electric bill.
The unit has four Sleep Modes to select from. Press the SLEEP
button to select Sleep 1, Sleep 2, Sleep 3, Sleep 4 modes or Cancel.
The SLEEP icon appears.
LIGHT:
This function allows the user to turn the display ON or OFF on
the front panel.
Press the light icon
to turn the indoor unit front panel ON or
OFF. The remote control displays the Light Icon
WIFI Button:
Press and hold this button for three seconds to turn WIFI function
on or off. See the "Operation of Smart Control" section for more
information.
Only the set point temperature appears on the front panel and on
the remote controller.
▲
" or"
▲
▼
" or "
" button to
▲
▼
" or "
" buttons, the
▲
▼
" or "
" button for 2 seconds.
.
Combination Buttons
Combination of "
▲
▼
Press "
" and "
or unlock the keypad. If the remote control is locked,
▼
"
displayed. In this case, pressing any button,
to acknowledge the keypad is locked. Repeat the process to unlock
the remote controller.
Combination of "MODE" and "▼" Buttons:
Switch between Fahrenheit and Centigrade. At unit OFF, press the
"MODE'" and "- " buttons simultaneously to switch between _C and
_F.
Energy- Saving Function
Under the cooling mode, press the "TEMP" and "CLOCK"
buttons simultaneously to start or stop the energy- saving function.
When the energy- saving function starts "SE" displays on the
remote controller, and the air conditioner adjusts the set
temperature automatically according to the factory setting to reach
the best energy- saving effect. Press the "TEMP" and "CLOCK"
buttons simultaneously again to exit the energy- saving function.
NOTE:
S
Under the Energy- Saving function, the fan speed
defaults to the auto speed and can not be adjusted.
S
Under the Energy- Saving function, the set temperature
can not be adjusted. Press the "TURBO" button and the
remote controller will not send the signal.
S
The Sleep and Energy- Saving functions can not operate
at the same time. If the Energy- Saving function has been
set under the Cooling mode, press the Sleep button to
cancel the Energy- Saving function, If the Sleep function
has been set under the Cooling mode, start the
Energy- Saving function to cancel the Sleep function.
46_F Heating Functions:
Under the heating mode, press the "TEMP" and "CLOCK" buttons
simultaneously to start the 46_F heating function. When this
function starts, the
controller, and the air conditioner maintains the heating status.
Press the "TEMP" and "CLOCK" buttons simultaneously again to
exit the 46_F heating function.
NOTE:
S
Under the 46_F heating function, the fan speed defaults
to the auto speed and it can not be adjusted.
S
Under the 46_F heating function, the set temperature can
not be adjusted. Press the TURBO button and the remote
controller will not send the signal.
S
The Sleep function and the 46_F heating function can
not operate at the same time. If the 46_F heating function
has been set under the Cooling mode, press the Sleep
button to cancel the 46_F heating function. If the Sleep
function was set under the Cooling mode, the 46_F
heating function cancels the Sleep function.
7
" and "▼" Buttons:
▲
" buttons simultaneously for 8 seconds to lock
blinks three times
"$
" and 46_F icons appear on the remote
is
Advertisement
