Do you have a question about the Navigator UV725 Series and is the answer not in the manual?
Questions and answers
Renee' Gullickson
May 20, 2025
Shark UV725. It was vacuuming just fine, but rotor stopped and completely went dead. The light turns on therefore there is power. Checked for obstructions and saw none.
1 comments:
Mr. Anderson
May 24, 2025
If the Shark UV725 vacuum stops working even though the power light is on and there are no obstructions, it could be due to the motorized floor nozzle overheating. This is indicated by a flashing red brushroll indicator light. To resolve this, turn off the vacuum, unplug it, remove any blockages, and let it cool down for at least 60 minutes before restarting.
11. DO NOT use without filters in place. or tables. potentially present risk to the user. 28. During cleaning or routine 12. Only use Shark® branded filters 22. Your Shark® vacuum may not maintenance, DO NOT cut anything 3. Use only identical replacement parts.
Page 3
ASSEMBLY ASSEMBLY (Click) (Click) (Click) (Click) (Click) (Click) 1. Place the Pod onto the Floor Nozzle Post. 2. Insert the Wand into the pod. 3. Attach the Lower Accessory Holder to the pod. 4. Insert the Handle into the top of the wand. 5.
WHOLE-HOME CLEANING WHOLE-HOME CLEANING SETTINGS CLEANING MODES POWER/SURFACE SWITCH SUCTION CONTROL UPRIGHT MODE The Suction Control Slider located on the To engage Brushroll, step on floor nozzle and Select surface setting: handle allows you to adjust the suction tilt handle back firmly. Press the Power/Surface O Off depending on the floor type.
EMPTYING THE DUST CUP CLEANING AND REPLACING THE FILTERS IMPORTANT: Unplug the power cord before performing any maintenance. Empty CLEANING FILTERS the dust cup each time you vacuum and periodically during cleaning, when debris Regularly rinse and replace the filters to maintain your vacuum's suction power. in the dust cup reaches the MAX fill line.
CHECKING FOR BLOCKAGES Self-Cleaning Brushroll Shark's self-cleaning brushroll automatically removes hair wrap. If some hair remains wrapped around the brushroll, continue cleaning to give it time to make its way to the dust cup. If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught behind the brushroll.
AVAILABLE ACCESSORIES TROUBLESHOOTING Power cord caught in brushroll or floor nozzle. Pet Crevice Tool This versatile, slender 8" tool removes • To minimize the risk of power cord damage, DO NOT run the vacuum over the power cord. pet hair from hard-to-reach spaces like If this occurs, immediately shut off power to the vacuum and remove the cord from the corners, ceilings, and between couch brushroll or nozzle.
FIVE (5) YEAR LIMITED WARRANTY REGISTER YOUR PURCHASE Benefits of registering your product and creating an account: The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of registeryourshark.com • Get easier, faster product support and SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original access to warranty information product only and is not transferable.
Page 9
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE. This Owner’s Guide is designed to help you get a complete understanding of your new Shark Navigator® Lift-Away® Upright Vacuum with Self-Cleaning Brushroll. SharkNinja Operating LLC US: Needham, MA 02494 CAN: Ville St-Laurent, QC H4S 1A7 1-800-798-7398 sharkclean.com...
Need help?
Do you have a question about the Navigator UV725 Series and is the answer not in the manual?
Questions and answers
Shark UV725. It was vacuuming just fine, but rotor stopped and completely went dead. The light turns on therefore there is power. Checked for obstructions and saw none.
If the Shark UV725 vacuum stops working even though the power light is on and there are no obstructions, it could be due to the motorized floor nozzle overheating. This is indicated by a flashing red brushroll indicator light. To resolve this, turn off the vacuum, unplug it, remove any blockages, and let it cool down for at least 60 minutes before restarting.
This answer is automatically generated