Related Manuals for ZoneVu ZSI-320
Summary of Contents for ZoneVu ZSI-320
- Page 1 ZSI-320 User Manual Issue 03 Page 1 of 20 ZSI-320 USER MANUAL ZSI-320 CCTV ISDN Controller Issue 03 MEYERTECH LIMITED...
-
Page 2: Table Of Contents
ZSI-320 User Manual Issue 03 Page 2 of 20 Contents Contents.................................... 2 Introduction ..................................3 What is a ZSI-320? ............................... 3 Operation ..................................4 Configuration..................................8 Config Version ................................8 PC1 Port..................................9 PC2 (MMT)Port ................................. 10 PC3 (Clear) Port ................................. 11 ZVM Port.................................. -
Page 3: Introduction
ZSI-320. What is a ZSI-320? Intersite communications A ZSI-320 is part of the Zonevu Site Controller family. It allows the interconnection of remote sites via an ISDN line. Video transmission The unit can operate as either a transmitter or a receiver. -
Page 4: Operation
ZSI-320 User Manual Issue 03 Page 4 of 20 Operation MEYERTECH LIMITED... - Page 5 ZSI-320 User Manual Issue 03 Page 5 of 20 MEYERTECH LIMITED...
- Page 6 ZSI-320 User Manual Issue 03 Page 6 of 20 MEYERTECH LIMITED...
- Page 7 ZSI-320 User Manual Issue 03 Page 7 of 20 Installation See ZSI-320 Installation Guide – available from Meyertech Technical Support MEYERTECH LIMITED...
-
Page 8: Configuration
Config Version This entry screen shows information relating to the firmware installed in the ZSI-320 Config structure The version number of the configuration data format within the attached ZSI-320. – see Mpower manual for more details. (stored) The version number of the configuration data format stored on the PC. – see Mpower manual for more details. -
Page 9: Pc1 Port
ZSI-320 User Manual Issue 03 Page 9 of 20 PC1 Port Internal use only – MUST NOT BE MODIFIED Baud Rate Internal use only – MUST NOT BE MODIFIED MEYERTECH LIMITED... -
Page 10: Pc2 (Mmt)Port
ZSI-320 User Manual Issue 03 Page 10 of 20 PC2 (MMT)Port Internal use only – MUST NOT BE MODIFIED Baud Rate Internal use only – MUST NOT BE MODIFIED ISDN initialisation A configuration string used to initialise the ISDN link. -
Page 11: Pc3 (Clear) Port
ZSI-320 User Manual Issue 03 Page 11 of 20 PC3 (Clear) Port site The site number associated with the ZSI-320s location. Default = 1 Baud Rate Internal use only – MUST NOT BE MODIFIED MEYERTECH LIMITED... -
Page 12: Zvm Port
To indicate that the unit is to make the decision on telemetry control from operators. If set to Off the unit will forward control request messages to the device on the ZVM port. Default = Off Telephone The telephone numbers for up to 50 sites (20 on earlier versions of ZSI-320) can be configured. MEYERTECH LIMITED... - Page 13 ZSI-320 User Manual Issue 03 Page 13 of 20 Index In each entry, the following can be configured site The site number of the remote dialup site. Default = 0 Tel. Number #1 The first ISDN number for the site Default = blank Tel.
-
Page 14: Site
ZSI-320 User Manual Issue 03 Page 14 of 20 Site Priority The priority used when requesting camera control from a local matrix on behalf of an operator using a remote video phone – see MM225 manual. Default = 4 (1 lowest) -
Page 15: Operation
If set to Off the unit will resolve all switching and telemetry issues itself. It will use the matrix output number defined in the next section and command the local matrix to switch. Default = On Matrix Output The matrix output number, which is connected to the ZSI-320 video input. Default = 4 MEYERTECH LIMITED... -
Page 16: Diagnostics
ZSI-320 User Manual Issue 03 Page 16 of 20 Diagnostics These commands, which can be issued by Mpower, are included in this document to assist in the diagnosis of problems. The use of these commands is at the users own risk and is subject to change without notice. -
Page 17: Support
2. The GRN will be logged by our staff along with the reported problem. 3. Pack the ZSI-320 into the original packing it was delivered in. Failure to do so means the unit may incur further damage in transit, which Meyertech cannot be responsible for. -
Page 18: Disposal
Issue 03 Page 18 of 20 c. Repair the ZSI-320 at a quoted cost. An official purchase order to cover the cost and return of the product will be required prior to commencement of repair. d. Advise you that the ZSI-320 is not repairable. You can then decide to have the product returned to you at the standard delivery charge or we can dispose of the product free of charge. -
Page 19: Warranty
ZSI-320 User Manual Issue 03 Page 19 of 20 Warranty Please refer to Meyertech Limited ‘Terms & Conditions of Sale of Goods & Services’ for interpretation. 1. If the Buyer establishes to the Seller's reasonable satisfaction that there is a defect in the materials... - Page 20 ZSI-320 User Manual Issue 03 Page 20 of 20 9. In the event that the Buyer discovers a material error which results in the Programmed Products not performing substantially in accordance with the Functional Specification, or the Licensed Programs not performing substantially in accordance with the relevant Program Documentation and notifies the Seller of the error within 90 days from the date of the Seller making available the respective software to the Buyer (the `warranty period") the Seller shall at its sole option either refund the price which...
Need help?
Do you have a question about the ZSI-320 and is the answer not in the manual?
Questions and answers