Marine type container refrigeration unit (82 pages)
Summary of Contents for Daikin LXE10E-A37
Page 1
ダイキン海上コンテナ冷凍装置 Marine type Container Refrigeration Unit サービスガイド・パーツリスト Service Manual・Parts List オプション機能編・Optional Functions・ LXE10E-A37 TR07-08...
Page 2
Important information regarding the refrigerant This product contains greenhouse gases covered by Kyoto Protocol. Do not discharge refrigirant into atmosphere. Refrigerant type : R134a GWP (1) value : 1430 (1) GWP=global warming potential The refrigerant quantity is indicated on the unit name plate.
Page 3
Covered Models Regarding the features and operation of the unit, the service guide describes the items which are different from those of the service manual TR01-09C. Different points from service manual Item (Maintenance and Repair) Fuse holder Provided. Cable clamp bracket Provided.
Page 4
CAUTION Before starting the unit, run the generator. Securely close the control box cover and the temperature recorder box cover (optional). Otherwise, It will cause water entry. Temperature recorder box cover Quick-lock lever Control box cover Quick-lock lever...
1. Operation Range Use this unit in the following range. Item Operational range Range of outdoor temperature -30° C to +50° C (-22< to +122<) Range of temperature inside -30° C to +30° C (-22< to +86<) 50Hz: 380/400/415VAC, 60Hz: 440/460VAC Voltage Range of voltage fluctuations: ±10%...
5. F.PTI Specification In order to perform F.PTI operation, this unit is designed by adding the following ① to ④ functions to the standard specification, which are enclosed with a dotted rectangular as shown below. ①Entry of set temperature while in F.PTI mode Press the ...
Page 9
③List of detail on display and alarms of F.PTI step Step Item Alarm display Outside outdoor temperature J501 condition Check the pull-down period to reach 0° C J502 Pull-down period -exceeded- Check the chilled operation for controllability. Outside commencement condition of...
6. Transducer 6.1 Low pressure transducer (LPT) y Apply the heat shrinkage tube in the Model LXE10E-A37 following position, then shrink it with hot air Transducer type NSK-BD010F of a dryer. Transducer Black body w Connector e Flare nut...
Page 33
ORDERING INSTRUCTIONS The parts list contains the parts of the DAIKIN Marine Type Container Refrigeration Units. Please read the following items before using the list. 1. When ordering the parts, be sure to specify the model No., the name of part and the type of part.
Page 34
Denomination of Model Name L X E NOMINAL HORSE POWER 5 : 5 10 : 10 CONDENSER COOLING TYPE NIL : AIR and WATER COOLED TYPE A : AIR COOLED TYPE OPTION NUMBER Note) "R" GIVEN AFTER OPTION NUMBER STANDS FOR "REVISION"...
Page 35
C O N T E N T S 目 次 Page A. Parts related with the unit(outside)………………………………………………………………………34 庫外関連部品 B. Parts related with refrigerant piping(outside) …………………………………………………………36 庫外冷媒配管関連部品 C. Parts related with the unit(inside) ………………………………………………………………………40 庫内関連部品 D. Parts related with refrigerant piping(inside) …………………………………………………………42 庫内冷媒配管関連部品...
Page 36
Parts related with the unit(outside) 庫外関連部品 (Refer to 77Page) (Refer to 76Page) (Refer to 77Page)
Page 37
Parts related with the unit(outside) 庫外関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 1549647 Power plug(400V class) 3P130172-1 電源プラグ(400V) 0954936 Condenser fan motor 3P005566-1 凝縮器電動機 0980618 Fan Brade(outside)
Page 38
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 B7-6 B7-5b B7-5-1 B11詳細(Detail of B11) Discharge pipe B7-4 B7-3 Feeler bulb inserting pipe B7-1 B13詳細(Detail of B13) Suction pipe Feeler bulb inserting pipe B7-5a B7-5-1 B12詳細(Detail of B12) In case of A5D B8-1-1 B8-1-2 B7-7 B7-2 B8-1-3 B8-1-5 View A-A...
Page 39
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 1199415 Compressor JT224D-NYR 圧縮機 1387173 Air cooled condenser 2P089486-1 CA-LXE10E1 空冷凝縮器 1757703 Discharge pipe ass'y 2P117329-1 吐出配管組立品...
Page 40
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 B7-7 0964166 Strainer 4P012568-1 ストレーナ 1496781 Suction pipe ass'y(inside) 3P071569-2 吸入配管組立品(庫内) B8-1 1254538 Suction modulating valve ass'y...
Page 41
Parts related with refrigerant piping(outside) 庫外冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数...
Page 42
Parts related with the unit(inside) 庫内関連部品 C1-1 Option C1-2 Option E57詳細(Detail of E57) Sealing compound (KE44RTV or its equivalent) シール剤 (KE44RTV又は相当品) INSIDE OUTSIDE PUTTY (Equivalent of NEO-SEAL B-1) パテ (ネオシールb-1相当品) A詳細(Detail of A) <Without recorder> DRS(Blue・Red) RS(Blue) C23詳細(Detail of C23) <Without recorder>...
Page 43
Parts related with the unit(inside) 庫内関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 C1-1 0955333 Three phase AC fan motor 3PA07524-4 三相交流ファン電動機 C1-2 0955340 Three phase AC fan motor...
Page 44
Parts related with refrigerant piping(inside) 庫内冷媒配管関連部品 D4詳細(Detail of D4) D3-3 D3-4 D3-5 D3-2 Feeler bulb inserting pipe D3-2 D5詳細(Detail of D5) D3-8 D3-6 D3-9 D3-1 D3-10...
Page 45
Parts related with refrigerant piping(inside) 庫内冷媒配管関連部品 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 1562789 Evaporator 2P089487-1 CRB-LXE10E5 蒸発器組立品 1714009 Drain pan pipe ass'y 2P167654-2 ドレンパン配管組立品 1683941 Heat exchanger ass'y with insulation 熱交換器防露筒組立品...
Page 46
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) C詳細(Detail of C) B詳細(Detail of B) Tie wrap Wires E断面...
Page 47
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) ※(L = XX mm) indicates the length of cushion rubber E35.(Cut to suit pipe size.) ※(L = XX mm)と表記のものは、緩衝ゴム(E35)の長さです。(配管のサイズに合わせて切って使用ください。) 矢視A/B(View A/B) 矢視D(View D) (L=65mm) 受液機器部詳細 (L=90mm) (Receive part detail) E7/8 (L=60mm) ドライヤー部詳細 圧力センサー配管部詳細 (Dryer part detail) (Pressure tranducer detail) E31(L=40mm)
Page 48
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) EFM1 EFM2 矢視A(VIEW A)
Page 49
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) FAN GUIDE ファンガイド...
Page 50
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等)...
Page 51
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 1266694 Set plate, discharge pipe 4P079462-1 Page45 吐出配管取付板 1266702 Fixture plate, receiver 4P011318-2 t1.5...
Page 52
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 1267091 Wiring protection bush 4P023920-1 BLACK Page40 配線保護ブッシュ 1381012 Protection rubber...
Page 53
Other parts(Pipe clamp, sealing and insulation material etc.) その他部品(配管固定具、シール材、防熱材等) QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数...
Page 56
Control box コントローラボックス QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 ワイヤハーネス組立品 1726468 Wire harness ass'y(RM) 2P171113-11 (モニタリングレセプタクルケーブル) 1136407 Hinge(control/box cover) 平蝶番 (コントロールボックス蓋) 4P021346-1 1796289 Control box welding ass'y 2P197567-1 コントロールボックス組立品...
Page 57
Control box コントローラボックス QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 F34-9 1267596 Locking wire saddle 4P015570-2 ロッキングワイヤサドル F34-10 1267604 Flat cable clamp フラットケーブルクランプスナップタイプ 4P015573-1 F34-12 1267611 Speed bolt...
Page 58
Parts related with name plate 銘板関連 コントロールボックス内部(Inside of Control Box) G7,G8,G9,G10,G11...
Page 59
Parts related with name plate 銘板関連 QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 1584291 Ventilator name plate 4P146327-1 t0.05 換気口銘板(統合仕様) 1267952 Name plate, ventilator arrow 4P018502-1 ベンチレータ矢印銘板...
Page 60
Parts related with option 1 – MODEM オプション関連部品1 – モデム MODEM モデム Supply by customer...
Page 61
Parts related with option 1 – MODEM オプション関連部品1 – モデム QTY/UNIT PARTS NO. DWG. NO. TYPE SPECIFICATION REMARKS INDEX PARTS NAME 1台当たりの 部品名称 符号 部品番号 図面番号 形式 仕様 備考 所要数 0954640 Noise filter 2PA51273-1 ZCB2206-11 ノイズフィルタ 1267736 Connector for MODEM...
Page 62
List of size for standard pipe clamp 配管固定具サイズ表 1.Resin clamp 1.樹脂バンド (外穴) (OUTER HOLE) (内穴)(外穴) (INNER HOLE)(OUTER HOLE) (INTERMEDIATE HOLE) (内穴)(中穴)(外穴) (INNER HOLE) (OUTER HOLE) SIZE サイズ PARTS NO. DWG NO. PARTS NAME 部品名称 符号 部品番号 図面番号 E10 1222764 Resin clamp NE41015-9 26.9...
Page 63
List of size for standard pipe clamp 配管固定具サイズ表 2.Tube clamp 2.管止金 2-φ5.5穴 SIZE サイズ PARTS NO. DWG NO. PARTS NAME 部品名称 符号 部品番号 図面番号 使用個数 E15 0782775 Tube clamp 管止め金 NE31016-51 E16 1584215 Nylon coating tube clamp ナイロンコーティング管止め金 4P143802-51 E17 1584208 Nylon coating tube clamp ナイロンコーティング管止め金 4P143802-52...
Page 64
Notes for ordering spare parts 部品発注の際の注意事項 1.Parts recommended to be ordered together with packing, gasket, sealing material and name plate 1.発注の際にパッキングやシール材、銘板等の同時発注を推奨する 部品 For ordering following spare parts, we recommend that you order the following packing, gasket, sealing material and name plate together at the same time. 上記のサービス扉やボックスカバーを発注の際には、下記のパッキングを同時に発注 することをおすすめします。 (1)Service door (1)サービス扉 PARTS NO. DWG NO. REMARKS PARTS NAME 部品名称 符号 部品番号 図面番号 備考 (Without cushion and Access panel サービス扉 sealing material) A4 1612576 1P006678-5 (FRP) 組立品 ...
Page 65
Notes for ordering spare parts 部品発注の際の注意事項 (3)Ventilation cover (3)換気口蓋 PARTS NO. DWG NO. PARTS NAME 部品名称 符号 部品番号 図面番号 A19 1266120 Ventilation cover 換気口蓋 3P067053-1 Sealing material シール材 A20 1266221 4P016185-1 (access panel) (換気口) (4)Front plate (CA) (4)前板(CA) PARTS NO. DWG NO.
Page 66
Notes for ordering spare parts 部品発注の際の注意事項 2.Order for motorized valve, solenoid valve and pressure regulating valve 2.電動弁・電磁弁・圧力調整弁の発注 Refer to the following table for the name, main body, solenoid coil and ass'y of solenoid valves etc. applied to this model. この機種に使用されている電磁弁等の名称と本体・ コイル・組立品は下記のとおりです。 Common Parts 共通部品 Body/Coil PARTS NO. DWG NO. PARTS NAME 部品名称 本体/コイル 符号 部品番号 図面番号 本体 Body B7-3 125649J Electronic expansion valve body 電子膨張弁本体 2SA50010-2-KU 1.EV 138143J Electronic expansion valve coil 電子膨張弁コイル...
Page 67
Notes for ordering spare parts 部品発注の際の注意事項 3.Order for pressure trasducer 3.圧力センサーの発注 Refer to the following table for the pressure transducer applied to this model. For ordering pressure transducer, we recommend that you order the following best shrinkable tube together at the same time. この機種に使用している圧力センサーは下記の通りです。 圧力センサー発注の際は、下記の熱収縮チューブを同時に発注することをおすすめし ます。 PARTS NO. DWG NO. TYPE REMARKS PARTS NAME 呼称名 部品名称 図面番号 形式 備考 符号 部品番号 HPT B16 1587959 High pressure transducer (HPT) 高圧圧力センサ(HPT) 3P141602-1 B15 1587942 Low pressure transducer (LPT) 低圧圧力センサ(LPT) 3P141601-1...
Page 68
Notes for ordering spare parts 部品発注の際の注意事項 4.Order for temperature sensor 4.温度センサーの発注 Refer to the following table for temperature sensors applied to this model. この機種に使用されている温度センサーは下記の通りです。 Lot marks Type No. 表示 型番表示 Lot marks Type No. LOT 表示 型番表示 5Y01 ST9503-1- 1210 ST9701- Length Length ※Operating temp. range ー30〜+150℃ ※Operating temp. range ー30〜+70℃ 使用温度範囲 ー30〜+150℃ 使用温度範囲 ー30〜+70℃ Lot marks Type No. LOT 表示 型番表示 7828 ST9703-1 Length ※Operating temp. range ー30〜+15℃...
Page 69
Measuring and adjusting tools 測定調整用工具 1.Tools for emergency operation 1.緊急運転用工具 PARTS NO. DWG NO. ILLUSTLATION PARTS NAME 部品名称 用途 姿図 符号 部品番号 図面番号 For electronic Emergency coil エマージェンシー expansion 1080263 3P017370-1 valve コイルキャップ 電子膨張弁用 Suction modulating E m e r g e n c y エマージェンシー...
Page 70
Measuring and adjusting tools 測定調整用工具 2.Personal computer cable (for DCCS) 2.パソコンケーブル(DCCS用) The following parts are connector cables required to exchange information between the refrigeration unit and personal computer. The table below describes parts required to apply to Model LXE-C, -D, and -E new model. 下記の部品は冷凍ユニットとパソコンの情報交換に必要なコネクター、ケーブル類で す。LXE-C型、 D型、及び新機種E型対応に必要な部品を掲載しています。 [TYPE A]タイプA LXE10C LXE10C LXE10CA LXE10CA 1.5m LXE10D for MOL MOL用LXE10D (Receptacle) (レセプタクル) RS232C (Female) RS232C(メス) on the controller コントローラー側 [TYPE B]タイプB 0.3m 1.5m LXE10D LXE10D...
Page 71
Measuring and adjusting tools 測定調整用工具 Illustlation Internal Wiring 符号 姿図 内部配線 RS232C RS232C Female Female メス メス Frame Frame フレーム フレーム Daikin RS232C made Female ダイキン製 メス White Black Daikin RS232C made Female ダイキン製 メス Red 赤 White 白 Black 黒 Frame フレーム ...