Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dantherm Gulliver RG3
Summary of Contents for Dantherm Gulliver RG3
- Page 1 Oilburner Code No.: 970929...
-
Page 2: Oil Burner
Instruction Oilburner Type Gulliver RG3 This instruction should be kept in the furnace room The user is responsible for the burners working order and that the following points are observed. Please check before ignition: Interruptions: – that the valves on the oil pipes are open –... -
Page 3: Technical Instructions
Technical instructions Oilbuner Type Gulliver RG3 Main components of the oilburner, dimensions Type 393 T1 Terminal power – output 87,4 – 188,4 kW (H ) (7 – 15 kg/h) Fuel Viscosity max. 6 mm /s (1,5° E) at 20° C... -
Page 4: Burner Start-Up Cycle
Technical instructions Oilburner Type Gulliver RG3 Capacity diagram, start-up cycle In the capasity diagram below the burner maximum preformance (Bmax) is in proportion to the positive pressure of the combustion chamber (Po). [mbar] [kW] [kg/h] Burner start-up cycle: Normal Lock-out due to failure to light... - Page 5 Assembling Oilbuner Type Gulliver RG3 Dimensioning of oil pipes One-line system: The pump is designed to allow working with two pipes. In order to obtain one pipe working it is necessary to unscrew the return plug (2), remove the by-pass screw (3) and then screw again the plug (2).
- Page 6 Assembling Oilburner Type Gulliver RG3 Dimensioning of the oil pipes One-line system: On the tank installa- tion, where vacuum can occur in the oil tubes, you install a flow-control between the front filter and the oil burner. The pump suction should not exceed a maximum of 0.4 bar (30 cm Hg).
- Page 7 Assembling Oilbuner Type Gulliver RG3 Cables and control box Electrical wiring: El cable (min. 1 mm ) with 7-pin plug Wieland plug on the burners control box. The control box has intern 230 V/5 Amp. fuse (B). If the fuse should be defect the oil burner will not...
- Page 8 Adjustment Oilburner Type Gulliver RG3 Accessibility to the nozzle: Remove nozzle-holder assembly (1) after loosing screws (2) and nut (3), remove the small cables (4) from the control box, the photoresistance (6). Withdraw the small cables (4) from the electrodes, remove the diffuser disc-hol- der assembly from the nozzle-holder as- sembly (1) after loosing screw (3, fig.
-
Page 9: Combustion Adjustment
Adjustment Oilbuner Type Gulliver RG3 Combustion adjustment: To suit the required appliance output, fit the nozzle then adjust the pump pressure, and the air damper opening in accordance with the following schedule. Nozzles recommended: Delavan: Type W – B Danfoss: Type S –... -
Page 10: Electrical Wiring
Electrical wiring Oilburner Type Gulliver RG3 Page 8 of 9 K:\framen\instrukt\Dantherm\RG\Engelsk\RG3\RG3.fm-E1-021108-dm/lbk... -
Page 11: Exploded View
Exploded view Oilburner Type Gulliver RG3 Spare parts overview Pos. Code No Description Pos. Code No Description 80002702 Cover 80007495 Electrode assembly Lead coil Collar 80002496 80007646 Coil Gasket 80002451 80005813 80002495 Suntec pump 80005814 Flange Tube Blast tube 80007663 80007647 P.e.