Stihl HS 45 Instruction Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Trimmer
  5. HS 45
  6. Instruction manual

Stihl HS 45 Instruction Manual

Hide thumbs Also See for HS 45:
Table of Contents

Advertisement

Quick Links

Download this manual
STIHL HS 45
2 - 18
Instruction Manual

Advertisement

Table of Contents
loading

Related Manuals for Stihl HS 45

Summary of Contents for Stihl HS 45

  • Page 1 STIHL HS 45 2 - 18 Instruction Manual...

  • Page 2: Table Of Contents

    Disposal............ 17 EC Declaration of Conformity....17 Engineering improvements UKCA Declaration of Conformity....18 STIHL's philosophy is to continually improve all Dear Customer, of its products. For this reason we may modify Thank you for choosing a quality engineered the design, engineering and appearance of our STIHL product.
  • Page 3 The machine must not be used for any other purposes – risk of acci‐ dents! STIHL can supply a comprehensive range of per‐ sonal protective equipment. Other uses are not permitted and may lead to accidents or damage to the machine.
  • Page 4 (clean, sharp, not bent or warped), correctly mounted and thor‐ Gasoline is an extremely flammable oughly sprayed with STIHL resin solvent (lubri‐ fuel. Keep clear of naked flames. Do not spill any fuel – do not smoke.
  • Page 5 2 Safety Precautions and Working Techniques English 2.6.1 Right-handed users Note that the cutting blades continue to run for a short period after you let go of the throttle trigger - flywheel effect! The gearhead becomes hot during operation. To reduce the risk of burn injury, do not touch the gear housing! Take special care in slippery and wet conditions,...
  • Page 6 (e.g. tingling sensation in fingers), seek medical advice. If the hedge is very dusty or dirty, spray the cut‐ ting blades with STIHL resin solvent from time to 2.10 Maintenance and Repairs time during cutting. This will significantly reduce blade friction, the aggressive effects of sap and Service the machine regularly.

  • Page 7: Using The Unit

    Check the fuel filler cap for leaks at regular inter‐ vals. Use only a spark plug of the type approved by STIHL and make sure it is in good condition – see "Specifications". Inspect the ignition lead (insulation in good con‐...

  • Page 8: Fuel

    25% (E25). 4.2.2 Engine Oil If you mix the fuel yourself, use only STIHL two- Hold the cutter bar at an angle of 0° to 10° as stroke engine oil or another high-performance you swing the hedge trimmer horizontally.

  • Page 9: Fueling

    Starting / Stopping the STIHL MotoMix may be stored for up to 2 years without any problems. Engine ► Thoroughly shake the mixture in the canister ► Observe safety precautions – see chapter on before fueling your machine.
  • Page 10 English 6 Starting / Stopping the Engine Cranking WARNING Make sure the carburetor is correctly adjusted. The cutting blades must not move when the engine is idling. Your machine is now ready for operation. Stopping the Engine ► Move the stop switch to O. Other Hints on Starting ►...

  • Page 11: Operating Instructions

    7 Operating Instructions English Cleaning the Air Filter ► Press the manual fuel pump bulb (6) at least five times – even if the bulb is filled with fuel. If there is a noticeable loss of ► Now start the engine. engine power Operating Instructions During break-in period...

  • Page 12: Adjusting The Carburetor

    ► Fit a new spark plug after about 100 operating hours – or sooner if the electrodes are badly eroded. Install only suppressed spark plugs of the type approved by STIHL – see "Specifica‐ tions". 10.1 Removing the Spark Plug ►...

  • Page 13: Engine Running Behavior

    Have the muffler checked for contamination (car‐ bonization) by your servicing dealer. STIHL recommends that you have servicing and After about 50 hours of operation: repair work carried out exclusively by an author‐...

  • Page 14: Sharpening Instructions

    NOTICE It is best to have the cutting blades resharpened Do not operate your machine with dull or dam‐ by a dealer on a workshop sharpener. STIHL aged cutting blades. This may cause overload recommends a STIHL servicing dealer. and will give unsatisfactory cutting results.

  • Page 15: Minimize Wear And Avoid Damage

    Gearbox lubrication Check and replenish after every 50 hours of operation Safety labels Replace 1)STIHL recommends an authorized STIHL servicing dealer. 17 Minimize Wear and Avoid 17.1 Maintenance Work Damage All the operations described in the "Maintenance Chart" must be performed on a regular basis. If Observing the instructions in this manual helps these maintenance operations cannot be per‐...

  • Page 16: Main Parts

    – Clutch – Filters (air, fuel) 19 Specifications – Rewind starter – Spark plug 19.1 Engine – Components of antivibration system STIHL single cylinder two-stroke engine 18 Main Parts Displacement: 27.2 cc Bore: 34 mm Stroke: 30 mm Engine power to ISO 7293: 0.75 kW (1 bhp) at...

  • Page 17: Maintenance And Repairs

    Exhaust Emissions The CO value measured in the EU type approval STIHL products must not be thrown in the gar‐ procedure is specified at www.stihl.com/co2. bage can. Take the product, accessories and packaging to an approved disposal site for envi‐...

  • Page 18: Ukca Declaration Of Conformity

    Equipment for Use Outdoors Regulations 2001, 104 dB(A) Schedule 8, using the ISO 11094 standard. Technical documents deposited at: Measured sound power level ANDREAS STIHL AG & Co. KG 102 dB(A) Produktzulassung Guaranteed sound power level The year of manufacture and serial number are applied to the product.
  • Page 19 23 UKCA Declaration of Conformity English 0458-253-0121-E...
  • Page 20 *04582530121E* 0458-253-0121-E...

Table of Contents