Advertisement
Assembling the hi-hat stand
1.
5.
Loosen the hi-hat clutch's wing bolt b and remove the hi-hat
If a drum mat (sold separately) is not available, lay a sheet of
cardboard on the floor to prevent it from being scratched.
clutch.
2.
* The hi-hat clutch is not required when assembling the elec-
Loosen the hi-hat stand's wing bolt a.
tronic drum kit in the standard fashion described in this
3.
manual. Instead, the hi-hat clutch that came with the
Open up the three legs as shown below and then retighten
RHH135 Real Hi-hat Pad will be used.
the wing bolt a to lock them in place.
6.
4.
Remove the hi-hat shaft
Insert the footboard stabilizer rods into the frame holes as
shown below.
7.
Insert the hi-hat shaft
go into the lower tube
a
Wing bolt
8.
Insert the upper tube
the wing bolt c to secure it in place with the cymbal support
approximately half way between the top of the lower tube
and the top of the hi-hat shaft
9.
Remove the felt washer attached above the cymbal support.
* Do not remove the Metal washer.
* The felt washer is not used when assembling the electronic
drum kit in the standard fashion described in this manual.
Footboard
If you leave it on, you will not be able to get the proper play-
Footboard
stabilizer rod
ing feeling, so be sure to remove it.
stabilizer rod
Assembling the drum trigger module and cymbal pads
Cymbal pads
PCY135 cymbal pad
PCY175 cymbal pad
1.
Using the drum key, loosen
PCY155 cymbal pad
the stopper's key bolt.
Drum trigger
module
2.
Remove the wing nut, the two felt
pads, and the bolt cover from the
cymbal holder.
Drum trigger module
1.
Secure the module holder to the bottom of the drum trigger
module using the module holder screws.
Module holder screw (×4)
3.
Place the stopper on the cymbal holder.
Module holder
* If the key bolt was not sufficiently loosened in Step 1
above, the cymbal holder may not pass through the hole of
Drum trigger module
the stopper. In such a case, loosen the key bolt as much
(rear side)
as possible without removing it.
4.
Replace the bolt cover.
* Turn the bolt cover to tighten it
2.
Push the module holder into the holder clamp and tighten the
onto the threaded section and
fixing bolt to secure it in place.
firmly secure it in place.
Drum trigger module
+
module holder
Insert
Holder clamp
Fixing bolt
Assembling the kick pad
1.
If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to prevent it from being
scratched.
2.
Assemble the left and right leg to the main unit.
As shown below, with the bolt facing you, align the notch on the leg with the notch on the mounting, put the washer
into the wing bolt, and then secure the leg to the KP128 main unit.
NOTE
For details on assembling the foot pedal (sold separately), refer to the "Assembling the KP128" in the KP128 Owner's Man-
ual.
Notch
Wing bolt
Main unit
Washer
Bolt
Bolt
Hi-Hat clutch
b
from the upper tube
.
Cymbal
support
removed in Step 6 as far as it will
and screw in the tip.
over the hi-hat shaft
and tighten
.
10.
Assemble the RHH135 Real Hi-hat Pad.
* For detailed instructions, refer to the "Setting Up" in the
RHH135 Owner's Manual.
5.
With the stopper making full contact with the bottom surface
of the bolt cover as shown below, tighten the stopper's key
bolt using the drum key.
Stopper
Key bolt
Drum key
Drum key
Wing nut
Felt pads
6.
Place one of the felt pads removed in Step 2 on the cymbal
Bolt cover
holder.
7.
Mount the pad on the cymbal stand. Lower the pad into place
with the cymbal holder's shaft passing through the central
Cymbal
hole. When mounted, the stopper's pin should rest inside the
holder
pad's smaller hole.
* Playing your pad unit without the stopper's pin positioned
fully inside the smaller hole could cause slip out of the
hole. It is very important, therefore, to ensure that the stop-
per is secured as shown in Step 5 above.
8.
Assemble the other felt pad removed in Step 2 to the cymbal
holder.
9.
Tighten the wing nut to secure the pad to the cymbal holder.
Wing nut
Felt pad removed
Bolt cover
in Step 2
Cymbal pad
Stopper
Felt pad
Threaded
removed in
section
Step 2
Cymbal
Bolt cover
holder
Assembling the Snare Stand and Snare Pad
1.
Open up the snare stand's legs and stand it up on the floor.
2.
Open up the snare stand's basket section, lay the Snare Pad on it, adjust the
basket, and then tighten the adjusting knob to secure the pad and prevent it
from moving.
Basket
NOTICE
Adjusting
Before every playing, tighten
Legs
knob
the drum key bolts so that
XP125SD
there is no rattling and loos-
ening of the head, in order to
prevent malfunction. Refer to
the "Head tension adjust-
ment" in the KP128 Owner's
Manual.
4
Arrange the hi-hat stand, the kick pad, and the snare stand as shown in Example of standard assembly on the other side of this sheet.
• Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the kick pad. Alternatively, you can place cardboard from the drum kit packaging or the like
NOTICE
on the floor to prevent it from being scratched.
• Ensure that you do not lower the electronic drum rack's center strut too much as doing so may cause it to come into contact with the kick pad.
Felt washer
Connect the pads to the drum trigger module.
5
Metal washer
As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.
Cymbal
support
1.
c
Plug the straight ends of the ten-channel snake cable into the trigger input jacks on the back of the drum trigger module.
• When using the standard setup, the stickers on each of the snake cable's plugs will indicate the name of the corresponding pad.
2.
Plug the L-shaped ends of the ten-channel snake cable into the corresponding pads.
3.
Wrap the cables for the snare pad, the tom pads, the cymbal pads and the hi-hat pad around the cable clips to prevent them from being pulled out.
Excessive bending can damage pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips.
NOTICE
Trigger input jacks on the drum module
KICK
HH CON
HI HAT
Bolt cover
Full contact
Stopper
HH CON
HI HAT
SNARE
Cymbal holder
Ten-channel snake cable
4.
Using the cable bands, secure the cables to the electronic drum rack at the positions circled in the figure on the right. (
If you secure the cable band from the side closer to the drum trigger module, you can make connections more
easily.
6
Connect the drum trigger module to a power supply.
1.
Plug the AC adaptor's DC cord into the
Stopper's pin
adaptor's DC cord around the cord clip to secure it in place.
Cymbal pad
Smaller hole
CAUTION
Excessive bending can damage AC adaptor's DC cord. Ensure, there-
fore, that the cord is not bent at an extreme angle when wrapped
around the clips. Doing so can cause fire or electrical shock.
7
Setting up the drum trigger module.
Pin
Stopper
Cymbal holder
According to your particular electronic drum kit, select the "DTX10K-X" or the "DTX10K-M" trigger
setup on your drum trigger module. (For details on the trigger setup procedure, refer to the "Initial
Settings (Trigger Setup Wizard)" in the DTX-PROX Owner's Manual.)
IMPORTANT
The letters at the end of the model name ("X" or "M") indicates the pad type. "X" represents
TCS products and "M" represents mesh products. Selecting the wrong trigger setup will ad-
versely affect your ability to perform comfortably, since sensing when the drum is hit differs
depending on the pad type. Use the correct trigger setup that corresponds to your particular
electronic drum kit for optimum performance.
IMPORTANT
• You can play comfortably by striking near the YAMAHA logo. Adjust the height, angle and ori-
NOTICE
entation of the cymbal pad and hi-hat pad to a position where you can hit around the YAMAHA
logo naturally when performing. The correct setting position is that the YAMAHA logo of the
Before every playing, tighten the
cymbal pad and hi-hat pad are visible in front of the performer. The direction of the cymbal pad
drum key bolts so that there is no
will be appropriate by adjusting the direction of the stopper as shown on the right. The direction
rattling and loosening of the
of the hi-hat pad will also be appropriate by adjusting the direction of the hi-hat clutch.
head, in order to prevent mal-
• The hi-hat shaft will become loose while you continue to use the hi-hat, and the hi-hat pad may
function. Refer to the "Head ten-
rotate. Since this may adversely affect performance, screw in the hi-hat shaft periodically and
sion adjustment" in the XP105T-
adjust the position of the hi-hat pad.
X XP105T-M XP125T-X XP125T-M
XP125SD-X XP125SD-M Owner's
Manual.
Your electronic drum kit is now ready.
2
CRASH2
CRASH2
CRASH
RIDE
TOM3
TOM2
TOM1
SNARE
CRASH
TOM1
RIDE
KICK
TOM2
TOM3
CRASH2
TOM3
connector. Hook the AC
Cord clip
• Kick pad output (LEVEL) adjustment:
Adjust the trigger output to your desired setting by using the KP128 kick pad's level adjustment
knob. For details, refer to the "Adjusting the Output Level" in the KP128 Owner's Manual.
* For instructions on turning on the drum trigger module, producing sounds, and other subsequent steps,
refer to the Owner's Manual that came with the module.
RIDE
SNARE
CRASH
TOM2
TOM1
HI HAT HH CON
KICK
)
2.
Plug the adaptor's AC cord into a domestic wall
socket.
connector
Hi-hat shaft
Stopper's pin
YAMAHA logo
Screw in
Advertisement
