Related Manuals for CECOR SE15 Series
Summary of Contents for CECOR SE15 Series
- Page 1 OPERATION MANUAL & PARTS LIST MODELS: SE15 HORIZONTAL TANK SERIES 90, 140, & 200 GALLON...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SECTION 1 – SAFETY INFORMATION ......................3 1.1 – CAUTION ............................3 1.2 – PRECAUTIONS ..........................4 SECTION 2 – THE SUMP CLEANER ......................... 5 2.1 – UNIT IDENTIFICATION ........................5 2.2 – MODEL & SERIAL NUMBER ......................6 2.3 –... -
Page 3: Section 1 - Safety Information
SECTION 1 – SAFETY INFORMATION 1.1 – CAUTION CAUTION FLAMMABLE THIS EQUIPMENT IS INTENDED FOR USE WITH STANDARD METALWORKING FLUIDS (WATER-BASE & CUTTING OILS) INFLAMMABLE ONLY. IT SHOULD NOT BE USED WITH FLAMMABLE FLUIDS, (FUELS, PAINT, SOLVENTS, ETC.) CORROSIVE, TOXIC OR REACTIVE MATERIALS. -
Page 4: Precautions
1.2 – PRECAUTIONS READ THROUGH THE "OPERATIONS MANUAL" COMPLETELY BEFORE ATTEMPTING TO OPERATE THE MACHINE. CLEANOUT, POT LID, INLET CAP AND HOSES MUST BE IN PLACE AND TIGHTLY SECURED BEFORE OPERATION IN THE DISCHARGE MODE. TANK DISCHARGE PRESSURE MUST NOT EXCEED 10 PSI. REGULATOR AND RELIEF VALVES ARE SET BEFORE SHIPMENT AND SHOULD NOT BE CHANGED AS THE USE OF EXCESSIVE PRESSURE COULD CAUSE SERIOUS INJURY OR DAMAGE. -
Page 5: Section 2 - The Sump Cleaner
SECTION 2 – THE SUMP CLEANER 2.1 – UNIT IDENTIFICATION WHEN ORDERING PARTS OR ASKING QUESTIONS REGARDING YOUR SUMP SHARK, IT IS IMPORTANT TO HAVE THE MODEL AND SERIAL NUMBER OF THE UNIT. THE MODEL AND SERIAL NUMBER CAN BE FOUND ON THE SHARK’S NAMEPLATE LOCATED ON THE BACK PANEL OF THE PUMP BASE. -
Page 6: Model & Serial Number
2.2 – MODEL & SERIAL NUMBER THE MODEL NUMBER IDENTIFIES YOUR SHARK AND INDICATES STANDARD FEATURES ON YOUR MACHINE. THE SERIAL NUMBER IDENTIFIES YOUR SPECIFIC SHARK AND WILL HELP IDENTIFY ANY SPECIAL FEATURES THAT MAY BE UNIQUE TO YOUR SUMP SHARK. THE SERIAL NUMBER IS LOCATED ON THE NAMEPLATE. -
Page 7: Sump Cleanper Features
2.3 – SUMP CLEANPER FEATURES PUMP-TO-TANK SUCTION PUMP-TO-TANK CONNECTION DISCHARGE REMOVEABLE CONNECTION TOOLBOX SUCTION PORT ON/OFF DISCHARGE VACUUM/ SWITCH PORT PRESSURE GAUGE SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020) -
Page 8: Section 3 - Installation
SECTION 3 – INSTALLATION 3.1 – ASSEMBLE DISCHARGE CONNECTION FOR SHIPPING PURPOSE, SOME MODELS MAY REQUIRE THE INSTALL OF THE DISCHARGE VALVE AND QUICK DISCONNECT ADAPTER. USE PIPE SEALANT ON ALL JOINTS AND TIGHTEN SECURELY. 3.2 – LOOSE ITEMS SOME ITEMS MAY BE PACKAGED IN A BOX LOCATED ON THE SHIPPING PALLET. - Page 9 POLY STRAINER BAG FINE COARSE STRAINER BAG STRAINER BAG FLARE NOZZLE TOOLBOX STRAIGHT NOZZLE SUMP CLEANER HOSE FLEX NOZZLE QUICK CLEANOUT DISCONNECT DOOR COUPLER F10 BASKET ASSEMBLY SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020)
-
Page 10: Initial Startup
3.3 – INITIAL STARTUP 1. CLOSE AND SECURE ALL TANK SUCTION AND DISCHARGE PORTS. DISCHARGE SUCTION PORT PORT 2. PLUG IN POWER CORD TO PROPER ELECTRICAL CIRCUIT. SEE NAMEPLATE. SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020) - Page 11 RUN THE UNIT IN “SUCTION” MODE. WITH POWER SWITCH IN THE OFF, POSITION CONNECT THE PUMP-TO-TANK HOSE TO THE SUCTION CONNECTION. 4. TURN POWER SWITCH ON. THE VACUUM READING SHOULD INCREASE TO 10-13” HG. 5. TURN SWITCH OFF. THE NEGATIVE PRESSURE IN THE TANK WILL CAUSE THE PUMP TO ROTATE BACKWARDS UNTIL THE PRESSURE EQUALIZES.
- Page 12 RUN THE UNIT IN “DISCHARGE” MODE. CHANGE THE PUMP-TO-TANK HOSE TO DISCHARGE CONNECTION. 7. TURN SWITCH ON. THE PRESSURE READING SHOULD BE 5-7 PSI. 8. TURN SWITCH OFF. THE POSITIVE PRESSURE IN THE TANK WILL CAUSE THE PUMP TO ROTATE BACKWARDS UNTIL THE PRESSURE EQUALIZES. 9.
-
Page 13: Section 4 - Operation
SECTION 4 – OPERATION 4.1 – CLEANING A SUMP 1. ATTACH THE SUMP CLEANER HOSE TO THE SUCTION PORT, AND INSERT SUCTION TOOL INTO HOSE END. 2. RUN UNIT ON SUCTION MODE. (SEE INITIAL STARTUP 3.5, STEP 3.) 3. WHEN VACUUMING OUT THE SUMP, ATTACK THE SOLIDS FIRST. POSITION THE SUCTION TOOL IN THE AREAS THAT ARE PRIMARILY SOLIDS. -
Page 14: Discharging Fluid From The Sump Cleaner
4.2 – DISCHARGING FLUID FROM THE SUMP CLEANER 1. ATTACH THE SUMP CLEANER HOSE TO THE DISCHARGE PORT, AND CAP THE SUCTION PORT. 2. RUN UNIT ON DISCHARGE MODE. (SEE INITIAL STARTUP 3.5, STEP 6.) 3. POINT NOZZLE AT THE TARGET WHERE THE FLUID IS TO BE DISPENSED, SLOWLY OPEN DISCHARGE VALVE. -
Page 15: F10 Filter
4.3.1 – F10 FILTER 4.3.1.1 – EMPTYING FILTER 1. FOR BEST RESULTS, DISCHARGE LIQUID FROM SUMP CLEANER AND LET FILTER DRAIN FOR A FEW MINUTES BEFORE DUMPING. 2. LOOSEN THE THREE (3) WING NUTS HOLDING THE POT LID IN PLACE. 3. - Page 16 2. TUCK HANDLES IN BETWEEN FILTER AND PERFORATED BASKET. MAKE SURE COTTON BANDING(POLY-FILTER) OR SIDES OF FILTER ARE LYING ON POT LID GASKET COMPLETELY WITHOUT CREASES. 3. RE-INSTALL POT LID AND WING NUTS. 5. WITH UNIT IN SUCTION MODE AND POT LID CAPPED, TURN UNIT ON AND TO TIGHTEN WING NUTS.
-
Page 17: F23 Filter
4.3.2 – F23 FILTER 4.3.2.1 – EMPTYING FILTER 1. FOR BEST RESULTS, DISCHARGE LIQUID FROM SUMP CLEANER AND LET FILTER DRAIN FOR A FEW MINUTES BEFORE DUMPING. 2. LOOSEN THE THREE WING NUTS ON FILTER ASSEMBLY. 3. LIFT FILTER OUT OF SUMP CLEANER TANK USING HOIST OR FORKLIFT. CAUTION: KEEP HANDS AND FINGERS CLEAR OF POT OPENING IN SUMP CLEANER WHEN REMOVING FILTER! SE15 OPERATIONS MANUAL &... - Page 18 4. POSITION FILTER ABOVE CONTAINER INTO WHICH THE SLUDGE IS TO BE EMPTIED. DISTANCE BETWEEN BOTTOM OF FILTER AND CONTAINER BOTTOM OR “D” DIMENSION, SHOWN IN FIGURE BELOW, AND SHOULD BE APPROXIMATELY 2 TO 3 FEET ON F23 TO PREVENT DAMAGE TO FILTER SLEEVE WHEN DUMPED.
- Page 19 5. ATTACH LANYARD TO TRIGGER ASSEMBLY ON FILTER BOTTOM. 6. MOVE TO A SAFE DISTANCE FROM THE DUMPING ZONE (APPROXIMATELY 7 FEET). 7. PULL LANYARD TO RELEASE LATCH AND BOTTOM DOOR WILL OPEN DUMPING THE FILTER. 8. AFTER FILTER SLEEVE IS EMPTY, ROLL BOTTOM OF SLEEVE UP LOOSELY SO THAT THE BOTTOM END OF SLEEVE WILL BE CLOSED AND CLOSE BOTTOM DOOR.
- Page 20 4.3.2.2 – INSTALLING FILTER 1. LOOSEN THE TWO WING NUTS ON THE FILTER LID AND REMOVE LID. 2. PLACE BOTTOM END OF FILTER SLEEVE IN FILTER. 3. FOLD UPPER 1 ½” OF FILTER SLEEVE COLLAR OUT OVER LIP OF FILTER SO THAT THE GASKET IN LID WILL CLAMP IT IN PLACE.
-
Page 21: Cleaning The Sump Cleaner
4.4 – CLEANING THE SUMP CLEANER 1. GENERALLY, DISCHARGING THE FLUID OUT OF THE SUMP CLEANER IS ALL THAT’S NEEDED. SOME SOLIDS WILL ACCUMULATE IN THE BOTTOM OF THE SUMP AND WILL REQUIRE A COMPLETE CLEANOUT OCCASIONALLY. 2. THE SE15 HAS AN EASY TO REMOVE CLEANOUT DOOR AND CAN ACCESSED BY LOOSENING THE TWO WINGNUTS. -
Page 22: Section 5 - Maintenance
THAT WILL KEEP YOUR SUMP CLEANER IN TOP-NOTCH, DEPENDABLE CONDITION. ANY WORN OR DAMAGED PART SHOULD BE REPLACED IMMEDIATELY. CECOR STOCKS SUMP CLEANER PARTS AND MOST CAN BE SHIPPED THE SAME OR THE NEXT DAY. CALL 1-800-356-9042 TO ORDER PARTS. -
Page 23: Monthly Maintenance
5.3 – MONTHLY MAINTENANCE 1. CHECK FOR WEAR ON POT LID & F23 WING NUTS AND STUDS. 2. INSPECT SUMP CLEANER HOSE. 3. GREASE THE SWIVEL CASTER AND WHEELS. 5.4 – SEMI ANNUAL INSPECT MOTOR BRUSHES, REPLACE IF WORN. SE15 OPERATIONS MANUAL & PARTS LIST (Rev. -
Page 24: Section 6 - Troubleshooting
SECTION 6 – TROUBLESHOOTING PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION Will not start Power Supply Make sure the unit is plugged into the proper voltage. Circuit Breaker Check electrical supply fuses or circuit breaker. Vac Motor Brushes Check brushes; replace if needed. Loss of suction Vac/pres gauge reads Check filter. -
Page 25: Section 7 - Repair Parts List
SECTION 7 – REPAIR PARTS LIST 7.1 – WHEELS & CASTER Part No. Description SP-365 SWIVEL CASTER WITH POLY TIRED WHEEL SP-553 WHEEL POLY TIRED SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020) -
Page 26: Tank & Pump
7.2 – TANK & PUMP 10,11 Part No. Description TANK ASSEMBLY A220-750 (NEED TO SPECIFY GALLON CAPACITY AND TRANSPORT) A220-756 H- TANK PUMP ASSEMBLY SE15 ELECTRIC PUMP-TO-TANK HOSE A220-570 DISCONNECT ADAPTER SP-217 SP-198 DISCONNECT COUPLER COUPLER GASKET SP-262BN TOOL BOX A220-760 SE15 OPERATIONS MANUAL &... -
Page 27: Filter, Tools & Hose
7.3 – FILTER, TOOLS & HOSE 22,23 Part No. Description A210-431 F10 BASKET ASSEMBLY A210-474 STRAIGHT NOZZLE A220-149 FLARE NOZZLE A220-150 FLEX NOZZLE A220-142 SUMP CLEANER HOSE 16' B210-530 F10 POLY STRAINER BAG A210-529C F10 COARSE STRAINER BAG A210-529F F10 FINE STRAINER BAG A220-864 COUPLER ASSEMBLY SP-262BN-2... - Page 28 29,30 SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020)
- Page 29 Part No. Description SP-104 WING NUT A210-305 POT LID GASKET SP-612 PRESSURE SAFE QUICK DISCONNECT ADAPTER MALE 2” SP-373 SECURITY CHAIN SP-611 PRESSURE SAFE CAP SP-262BN-2 COUPLER GASKET SP-466 BUTTERFLY VALVE SP-154 TOGGLE SWITCH SP-544 POWER CORD SP-194 VACUUM/PRESSURE GAUGE SP-375 QUICK DISCONNECT ADAPTER SE15 OPERATIONS MANUAL &...
- Page 30 90-200 ONLY 42,43 Part No. Description A210-165 CLEANOUT DOOR GASKET A220-240 CLEANOUT DOOR ASSEMBLY SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020)
-
Page 31: F23 Filter
7.5 – F23 FILTER 50,51 Ref Part No. Description SP-104 WING NUT A220-102 FILTER LID GASKET A220-103 FILTER LID ASSEMBLY SP-612 DISCONNECT ADAPTER SP-373 SECURITY CHAIN SP-611 PRESSURE SAFE CAP SP-262BN-2 COUPLER GASKET A220-645 F23 FILTER SLEEVE COARSE (NOT SHOWN) A220-101 F23 FILTER SLEEVE GREEN POLY (NOT SHOWN) A220-731... -
Page 32: Section 8 - Warranty
SECTION 8 – WARRANTY WARRANTY STATEMENT PLEASE PRINT OUR WARRANTY AT HTTPS://CECOR.NET/CECOR-WARRANTY/ SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020) -
Page 33: Section 9 - Record Model & Serial Number
SECTION 9 – RECORD MODEL & SERIAL NUMBER WHEN YOU RECEIVE YOUR CECOR SUMP SHARK, RECORD THE MODEL NUMBER, SERIAL NUMBER AND DATE DELIVERED FOR YOUR RECORDS. MODEL #: ________________________________________ SERIAL #: ________________________________________ DELIVERED: ____________ / ____________ / ____________ SE15 OPERATIONS MANUAL & PARTS LIST... - Page 34 SE15 OPERATIONS MANUAL & PARTS LIST (Rev. 8/2020)