1. Manuals
  2. Brands
  3. CECOR Manuals
  4. Tank Equipment
  5. Sump Shark SE10 Series
  6. Operations manual & parts list

CECOR SE10 Series Operations Manual & Parts List

Horizontal tank 90-140 gallon
Hide thumbs Also See for SE10 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION MANUAL & PARTS LIST
MODELS:
SE30 HORIZONTAL TANK SERIES
90-140 GALLON

Advertisement

Table of Contents
loading

Related Manuals for CECOR SE10 Series

Summary of Contents for CECOR SE10 Series

  • Page 1 OPERATION MANUAL & PARTS LIST MODELS: SE30 HORIZONTAL TANK SERIES 90-140 GALLON...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS SECTION 1 – SAFETY INFORMATION ......................3 1.1 – CAUTION ............................3 1.2 – PRECAUTIONS ..........................4 SECTION 2 – THE SUMP CLEANER ......................... 5 2.1 – UNIT IDENTIFICATION ........................5 2.2 – MODEL & SERIAL NUMBER ......................6 2.3 –...

  • Page 3: Section 1 - Safety Information

    SECTION 1 – SAFETY INFORMATION 1.1 – CAUTION CAUTION FLAMMABLE THIS EQUIPMENT IS INTENDED FOR USE WITH STANDARD METALWORKING FLUIDS (WATER-BASE & CUTTING OILS) INFLAMMABLE ONLY. IT SHOULD NOT BE USED WITH FLAMMABLE FLUIDS, (FUELS, PAINT, SOLVENTS, ETC.) CORROSIVE, TOXIC OR REACTIVE MATERIALS.

  • Page 4: Precautions

    1.2 – PRECAUTIONS  READ THROUGH THE "OPERATIONS MANUAL" COMPLETELY BEFORE ATTEMPTING TO OPERATE THE MACHINE.  CLEANOUT, POT LID, INLET CAP AND HOSES MUST BE IN PLACE AND TIGHTLY SECURED BEFORE OPERATION IN THE DISCHARGE MODE.  TANK DISCHARGE PRESSURE MUST NOT EXCEED 10 PSI. REGULATOR AND RELIEF VALVES ARE SET BEFORE SHIPMENT AND SHOULD NOT BE CHANGED AS THE USE OF EXCESSIVE PRESSURE COULD CAUSE SERIOUS INJURY OR DAMAGE.

  • Page 5: Section 2 - The Sump Cleaner

    SECTION 2 – THE SUMP CLEANER 2.1 – UNIT IDENTIFICATION WHEN ORDERING PARTS OR ASKING QUESTIONS REGARDING YOUR SUMP SHARK, IT IS IMPORTANT TO HAVE THE MODEL AND SERIAL NUMBER OF THE UNIT. THE MODEL AND SERIAL NUMBER CAN BE FOUND ON THE SHARK’S NAMEPLATE LOCATED ON THE BACK PANEL OF THE PUMP BASE.

  • Page 6: Model & Serial Number

    2.2 – MODEL & SERIAL NUMBER THE MODEL NUMBER IDENTIFIES YOUR SHARK AND INDICATES STANDARD FEATURES ON YOUR MACHINE. THE SERIAL NUMBER IDENTIFIES YOUR SPECIFIC SHARK AND WILL HELP IDENTIFY ANY SPECIAL FEATURES THAT MAY BE UNIQUE TO YOUR SUMP SHARK. THE SERIAL NUMBER IS LOCATED ON THE NAMEPLATE.

  • Page 7: Sump Cleanper Features

    2.3 – SUMP CLEANPER FEATURES PUMP-TO-TANK PUMP-TO-TANK DISCHARGE SUCTION CONNECTION CONNECTION SUCTION PORT DISCHARGE ON / OFF VACUUM/ PORT SWITCH PRESSURE GAUGE SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)

  • Page 8: Section 3 - Installation

    SECTION 3 – INSTALLATION 3.1 – ASSEMBLE DISCHARGE CONNECTION FOR SHIPPING PURPOSE, SOME MODELS MAY REQUIRE THE INSTALL OF THE DISCHARGE VALVE AND QUICK DISCONNECT ADAPTER. USE PIPE SEALANT ON ALL JOINTS AND TIGHTEN SECURELY. SE10 OPERATIONS MANUAL & PARTS LIST (Rev.

  • Page 9: Loose Items

    3.3 – LOOSE ITEMS SOME ITEMS MAY BE PACKAGED IN A BOX LOCATED ON THE SHIPPING PALLET. PACKAGES WITH FILTER BASKET OR FILTER ASSEMBLIES WILL HAVE FILTERS INSTALLED. PLEASE REVIEW YOUR PACKING LIST TO SEE WHAT ADDITIONAL ITEMS YOU WILL BE RECEIVING. POLY STRAINER BAG FINE...

  • Page 10: Initial Startup

    3.4 – INITIAL STARTUP 1. CLOSE AND SECURE ALL TANK SUCTION AND DISCHARGE PORTS. SUCTION PORT DISCHARGE PORT 2. PLUG IN POWER CORD TO PROPER ELECTRICAL CIRCUIT. SEE NAMEPLATE. SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)
  • Page 11 RUN THE UNIT IN “SUCTION” MODE. WITH POWER SWITCH IN THE OFF, POSITION CONNECT THE PUMP-TO-TANK HOSE TO THE SUCTION CONNECTION. 4. TURN THE POWER SWITCH TO ON. THE VACUUM READING SHOULD INCREASE TO 13” HG. SE10 OPERATIONS MANUAL & PARTS LIST (Rev.
  • Page 12 5. TURN SWITCH OFF. THE NEGATIVE PRESSURE IN THE TANK WILL CAUSE THE PUMP TO ROTATE BACKWARDS UNTIL THE PRESSURE EQUALIZES. RUN THE UNIT IN “DISCHARGE” MODE. CHANGE THE PUMP-TO-TANK HOSE TO DISCHARGE CONNECTION. 7. TURN THE POWER SWITCH TO ON. THE PRESSURE READING SHOULD INCREASE TO 5-7 PSI.

  • Page 13: Section 4 - Operation

    9. MACHINE IS READY TO USE. SECTION 4 – OPERATION 4.1 – CLEANING A SUMP 1. ATTACH THE SUMP CLEANER HOSE TO THE SUCTION PORT, AND INSERT SUCTION TOOL INTO HOSE END. 2. RUN UNIT ON SUCTION MODE. (SEE INITIAL STARTUP 3.5, STEP 3.) 3.

  • Page 14: Discharging Fluid From The Sump Cleaner

    4.2 – DISCHARGING FLUID FROM THE SUMP CLEANER 1. ATTACH THE SUMP CLEANER HOSE TO THE DISCHARGE PORT, AND CAP THE SUCTION PORT. 2. RUN UNIT ON DISCHARGE MODE. (SEE INITIAL STARTUP 3.5, STEP 6.) 3. POINT NOZZLE AT THE TARGET WHERE THE FLUID IS TO BE DISPENSED, SLOWLY OPEN DISCHARGE VALVE.

  • Page 15: F10 Filter

    4.3.1 – F10 FILTER 4.3.1.1 – EMPTYING FILTER 1. FOR BEST RESULTS, DISCHARGE LIQUID FROM SUMP CLEANER AND LET FILTER DRAIN FOR A FEW MINUTES BEFORE DUMPING. 2. LOOSEN THE THREE (3) WING NUTS HOLDING THE POT LID IN PLACE. 3.
  • Page 16 2. TUCK HANDLES IN BETWEEN FILTER AND PERFORATED BASKET. MAKE SURE COTTON BANDING(POLY-FILTER) OR SIDES OF FILTER ARE LYING ON POT LID GASKET COMPLETELY WITHOUT CREASES. 3. RE-INSTALL POT LID AND WING NUTS. 5. WITH UNIT IN SUCTION MODE AND POT LID CAPPED, TURN UNIT ON AND TO TIGHTEN WING NUTS.

  • Page 17: F23 Filter

    4.3.2 – F23 FILTER 4.3.2.1 – EMPTYING FILTER 1. FOR BEST RESULTS, DISCHARGE LIQUID FROM SUMP CLEANER AND LET FILTER DRAIN FOR A FEW MINUTES BEFORE DUMPING. 2. LOOSEN THE THREE WING NUTS ON FILTER ASSEMBLY. 3. LIFT FILTER OUT OF SUMP CLEANER TANK USING HOIST OR FORKLIFT. CAUTION: KEEP HANDS AND FINGERS CLEAR OF POT OPENING IN SUMP CLEANER WHEN REMOVING FILTER! SE10 OPERATIONS MANUAL &...
  • Page 18 4. POSITION FILTER ABOVE CONTAINER INTO WHICH THE SLUDGE IS TO BE EMPTIED. DISTANCE BETWEEN BOTTOM OF FILTER AND CONTAINER BOTTOM OR “D” DIMENSION, SHOWN IN FIGURE BELOW, AND SHOULD BE APPROXIMATELY 2 TO 3 FEET ON F23 TO PREVENT DAMAGE TO FILTER SLEEVE WHEN DUMPED.
  • Page 19 5. ATTACH LANYARD TO TRIGGER ASSEMBLY ON FILTER BOTTOM. 6. MOVE TO A SAFE DISTANCE FROM THE DUMPING ZONE (APPROXIMATELY 7 FEET). 7. PULL LANYARD TO RELEASE LATCH AND BOTTOM DOOR WILL OPEN DUMPING THE FILTER. 8. AFTER FILTER SLEEVE IS EMPTY, ROLL BOTTOM OF SLEEVE UP LOOSELY SO THAT THE BOTTOM END OF SLEEVE WILL BE CLOSED AND CLOSE BOTTOM DOOR.
  • Page 20 4.3.2.2 – INSTALLING FILTER 1. LOOSEN THE TWO WING NUTS ON THE FILTER LID AND REMOVE LID. 2. PLACE BOTTOM END OF FILTER SLEEVE IN FILTER. 3. FOLD UPPER 1 ½” OF FILTER SLEEVE COLLAR OUT OVER LIP OF FILTER SO THAT THE GASKET IN LID WILL CLAMP IT IN PLACE.

  • Page 21: Cleaning The Sump Cleaner

    4.4 – CLEANING THE SUMP CLEANER 1. GENERALLY, DISCHARGING THE FLUID OUT OF THE SUMP CLEANER IS ALL THAT’S NEEDED. SOME SOLIDS WILL ACCUMULATE IN THE BOTTOM OF THE SUMP AND WILL REQUIRE A COMPLETE CLEANOUT OCCASIONALLY. 2. THE SE10 HAS AN EASY TO REMOVE CLEANOUT DOOR AND CAN ACCESSED BY LOOSENING THE TWO WINGNUTS.

  • Page 22: Section 5 - Maintenance

    THAT WILL KEEP YOUR SUMP CLEANER IN TOP-NOTCH, DEPENDABLE CONDITION. ANY WORN OR DAMAGED PART SHOULD BE REPLACED IMMEDIATELY. CECOR STOCKS SUMP CLEANER PARTS AND MOST CAN BE SHIPPED THE SAME OR THE NEXT DAY. CALL 1-800-356-9042 TO ORDER PARTS.

  • Page 23: Monthly Maintenance

    5.3 – MONTHLY MAINTENANCE 1. CHECK FOR WEAR ON POT LID WING NUTS AND STUDS. 2. INSPECT SUMP CLEANER HOSE. 3. GREASE THE SWIVEL CASTER AND WHEELS. SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)

  • Page 24: Section 6 - Troubleshooting

    SECTION 6 – TROUBLESHOOTING PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION WILL NOT START POWER SUPPLY. MAKE SURE THE UNIT IS PLUGGED INTO THE PROPER VOLTAGE. CIRCUIT BREAKER. CHECK ELECTRICAL SUPPLY FUSES OR BREAKER. LOSS OF SUCTION VAC/PRES GAUGE READS CHECK FILTER. IF FULL, EMPTY. IF BLINDED, FULL VACUUM BUT HAS CLEAN OR REPLACE WITH COARSE FILTER NO SUCTION.

  • Page 25: Section 7 - Repair Parts List

    SECTION 7 – REPAIR PARTS LIST 7.1 – WHEELS & CASTER Part No. Description SP-365 SWIVEL CASTER WITH POLY TIRED WHEEL SP-553 WHEEL POLY TIRED SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)

  • Page 26: Tank & Pump

    7.2 – TANK & PUMP 10,11 Part No. Description TANK ASSEMBLY CALL FOR INFO (NEED TO SPECIFY GALLON CAPACITY AND TRANSPORT) A220-807 H-TANK PUMP ASSEMBLY SE30 A220-507 PUMP-TO-TANK HOSE SP-217 DISCONNECT ADAPTER SP-198 DISCONNECT COUPLER SP-262BN COUPLER GASKET SE10 OPERATIONS MANUAL & PARTS LIST (Rev.

  • Page 27: Filter, Tools & Hose

    7.3 – FILTER, TOOLS & HOSE 18,19 18,19 SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)
  • Page 28 Part No. Description A220-101 POLY STRAINER BAG 2.3 cu.ft. A220-645 COARSE STRAINER BAG 2.3 cu.ft. A220-731 FINE STRAINER BAG 2.3 cu.ft. A220-152 FLEX NOZZLE A220-151 FLARE NOZZLE A210-965 STRAIGHT NOZZLE A220-864 COUPLER ASSEMBLY SP-262BN-2 COUPLER GASKET A220-145 DISPENSER HOSE A220-562 DISPENSER NOZZLE A220-147 SUMP CLEANER HOSE...

  • Page 29: Tank Connections, Gauge, Pump Consumables

    7.4 – TANK CONNECTIONS, GAUGE, PUMP CONSUMABLES 30,31 SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)
  • Page 30 Part No. Description A210-305 POT LID GASKET SP-104 WING NUT SP-437K PRESSURE RELIEF VALVE WITH ELBOW SP-194 VACUUM / PRESSURE GAUGE CONTROL BOX CALL FOR INFO SP-217 QUICK DISCONNECT ADAPTER SP-198 QUICK DISCONNECT COUPLER SP-262BN COUPLER GASKET A220-570 TANK TO PUMP CONNECTION HOSE SP-443 PRESSURE RELIEF VALVE SP-500...
  • Page 31 41,42 Part No. Description A210-165 CLEANOUT DOOR GASKET A220-240 CLEANOUT DOOR ASSEMBLY SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)

  • Page 32: F23 Filter

    7.5 – F23 FILTER 48,49 Ref Part No. Description SP-104 WING NUT A220-102 FILTER LID GASKET A220-103 FILTER LID ASSEMBLY SP-612 PRESSURE SAFE QUICK DISCONNECT ADAPTER SP-373 SECURITY CHAIN SP-611 PRESSURE SAFE CAP SP-262BN-2 COUPLER GASKET A220-645 F23 FILTER SLEEVE COARSE (NOT SHOWN) A220-101 F23 FILTER SLEEVE GREEN POLY (NOT SHOWN) A220-731...

  • Page 33: Section 8 - Warranty

    SECTION 8 – WARRANTY WARRANTY STATEMENT PLEASE PRINT OUR WARRANTY AT HTTPS://CECOR.NET/CECOR-WARRANTY/ SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)

  • Page 34: Section 9 - Record Model & Serial Number

    SECTION 9 – RECORD MODEL & SERIAL NUMBER WHEN YOU RECEIVE YOUR CECOR SUMP SHARK, RECORD THE MODEL NUMBER, SERIAL NUMBER AND DATE DELIVERED FOR YOUR RECORDS. MODEL #: ________________________________________ SERIAL #: ________________________________________ DELIVERED: ____________ / ____________ / ____________ SE10 OPERATIONS MANUAL & PARTS LIST...
  • Page 35 SE10 OPERATIONS MANUAL & PARTS LIST (Rev. 5/2022)

This manual is also suitable for:

Se30 series

Table of Contents