Download Print this page

Stopwatch; World Time - Casio Pathfinder PAW1500 Operation Manual

Casio pathfinder paw1500: user guide
Hide thumbs

Advertisement

Table of Contents
Operation Guide 3134 3205
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown
reaches zero, and at zero. The first five beeps (seconds 10 through 6) are
higher pitched than the final five beeps (seconds 5 through 1). The watch
emits a longer beep to signal when the countdown reaches zero.
Progress Beeper
The progress beeper actually includes two beepers: a reset time beeper and
a reset period beeper.
• Note that the reset time beeper and reset period beeper operate only while
the progress beeper is turned on. For more information, see "To turn the
progress beeper on and off".
Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. The watch
beeps each second of the final 10 seconds before the countdown reaches the
reset time.
Reset Period Beeper
The reset period is the portion of the countdown between the reset time and
zero. While timing is in the reset period, the watch will beep four times at the
top of each minute and 10 seconds before the end of the countdown.
Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes
Progress beeper: On
Start Time
Reset Time
Reset Period Beeper
10'00"
5'00"
4'00"
Reset Time Beeper
0'10"
0'09"
0'08"
0'07"
0'06"
0'05"
To configure countdown timer settings
1. While the countdown start time is on the display
in the Countdown Timer Mode, hold down E
until the countdown start time setting starts to
flash, which indicates the setting screen.
• If the countdown start time is not displayed,
use the procedure under "To use the
countdown timer" to display it.
2. Press D to move the flashing in the sequence
shown below to select other settings.
3. When the setting you want to change is flashing, use A and C to change
it as described below.
Setting
Screen
Use A (+) and C (–) to change the setting.
Start Time
• You can set a start time in the range of 1 to 60
minutes in 1-minute increments.
Use A (+) and C (–) to change the setting.
Reset Time
• You can set a reset time in the range of 1 to 5
minutes in 1-minute increments.
4. Press E to exit the setting screen.
• The reset time setting must be less than the countdown start time setting.
To turn the progress beeper on and off
Pressing B while the countdown start time is on the display or while a
countdown timer operation is in progress in the Countdown Timer Mode
toggles progress beeper operation on (
(
displayed).
To use the countdown timer
In the Countdown Timer Mode, press A to start
the countdown timer.
• The countdown timer measurement operation
continues even if you exit the Countdown Timer
Mode.
• The table below describes button operations you
can perform to control countdown operations.
To do this:
Stop the countdown operation
Resume a stopped countdown operation
Display the countdown start time
Stop the countdown operation and display the reset
time
Start the countdown from the displayed reset time
Reset Period
Countdown
End Beeper
3'00"
2'00"
1'00" 0'10"
0'00"
0'04"
0'03"
0'02"
0'01"
0'00"
Start
Reset
Time
Time
Button Operations
displayed) and off
Do this:
Press A.
Press A again.
While the countdown is
stopped, press C.
Press C.
Press A.

Stopwatch

The stopwatch lets you measure elapsed time,
Hours
split times, and two finishes.
1/100 second
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from
zero after it reaches its limit, until you stop it.
• The stopwatch measurement operation
continues even if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is
frozen on the display clears the split time and
returns to elapsed time measurement.
• All of the operations in this section are
Minutes
Seconds
performed in the Stopwatch Mode, which you
enter by pressing D.
Current time
To measure times with the stopwatch
Elapsed Time
A
A
A
J
J
Start
Stop
Re-start
Split Time
A
C
C
J
J
Start
Split
Split release
(SPL displayed)
Two Finishes
A
C
A
J
J
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time
of first runner.

World Time

World Time displays the current time in 33 cities
Current time in the zone
(29 time zones) around the world.
of the selected city code
• If the current time shown for a city is wrong,
City code
check your Home City time settings and make
the necessary changes.
• All of the operations in this section are
performed in the World Time Mode, which you
enter by pressing D.
To view the time in another city
In the World Time Mode, use A (east) and C
(west) to scroll through city codes (time zones).
• For full information on city codes, see the "City
Code Table".
Timekeeping
Mode time
To toggle a city code time between Standard Time and Daylight
Saving Time
1. In the World Time Mode, use A (east) and C
DST indicator
(west) to display the city code (time zone)
whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down E to toggle between Daylight
Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
• The DST indicator appears on the display
whenever you display a city code for which
Daylight Saving Time is turned on.
• You cannot toggle between Daylight Saving Time and Standard Time if the
displayed city code is
UTC
.
• Note that the DST/Standard Time setting affects only the currently
displayed city code. Other city codes are not affected.
A
C
J
J
Stop
Clear
A
C
J
J
Stop
Clear
C
C
J
J
Split release
Clear
Display time of
second runner.
9

Hide quick links:

Advertisement

Table of Contents
loading

  Related Manuals for Casio Pathfinder PAW1500

This manual is also suitable for:

31343205