Download Print this page

Casio Baby-G BG90-2B Operation Manual page 2

Casio baby-g bg90-2b: user guide

Advertisement

Operation Guide 5000
Alarms
You can set five independent Daily Alarms. When an
Alarm time
alarm is turned on, the alarm tone sounds when the alarm
(Hour : Minutes)
time is reached.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are six screens in the Alarm Mode. Five are for
alarms (indicated by numbers from
and one is for the Hourly Time Signal (indicated by
).
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
On/Off status
• You can select any one of three alarm beeper patterns.
Alarm number
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set an alarm, display one of the screens indicated by an alarm number from
through
.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (PM indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
• To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
• The alarm will sound using the currently selected beeper pattern.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
On/Off status
2. Press A to toggle it on (
OF
(
displayed).
• Turning on an alarm (
alarm on indicator on its Alarm Mode screen.
• In all modes besides the Alarm Mode, the alarm on
indicator is shown for any alarm that is currently turned
on.
• The alarm on indicator flashes while the alarm is
sounding.
Alarm on indicator
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
On/Off status
Signal (
).
2. Press A to toggle it on (
OF
(
displayed).
• Turning on the Hourly Time Signal displays the Hourly
Time Signal indicator on its Alarm Mode screen.
• While the Hourly Time Signal is turned on, the Hourly
Time Signal on indicator is shown on the display in all
modes besides the Alarm Mode.
Hourly time signal
on indicator
Stopwatch
The stopwatch lets you measure elapsed time, split times,
Minutes
Seconds
and two finishes.
• The display range of the stopwatch is 59 minutes,
59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
1/100 second
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Split Time
Start
Split
Split release
(
displayed)
Two Finishes
Split
Stop
Start
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
through
),
ON
displayed) and off
through
) displays the
ON
displayed) and off
Stop
Clear
Stop
Clear
Split release
Clear
Display time of
second runner.
Countdown Timer
You can set the countdown timer within a range of
Hours
Minutes
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which restarts the
countdown automatically from the original value you set
whenever zero is reached.
• All of the operations is this section are performed in the
Countdown Timer Mode, which you can enter using C.
Seconds
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is reset automatically to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds to signal when the countdown
reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
To configure countdown timer settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under "To use the countdown timer" to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Hours
3. While a setting is flashing, use D and B to change it as described below.
Screen
To do this:
0:00
Change the hours or minutes
ON
Toggle auto-repeat on (
) and off (
• To specify a countdown start time of 24 hours, set
4. Press A to exit the setting screen.
• The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
Edit Mode
You can use the Edit Mode to configure the following settings, or to return the settings
to their initial factory defaults.
• Button operation tone on/off
• Alarm beeper pattern
• 12/24-hour timekeeping
• 00-second animation on/off
• Analog hand setting
• The analog hand setting will not change when you reset settings to their initial
factory defaults.
• All of the operations in this section are performed in the Edit Mode, which you enter
by pressing C.
• Each press of D cycles through available settings in the sequence shown below.
Press
.
Button Operation
Alarm Beeper
Tone (
)
Pattern (
Analog Hand Setting
(
)
Button Operation Tone
The button operation tone sounds any time you press one of the watch's buttons. You
can turn the button operation tone on or off as desired.
• Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and
Countdown Timer Mode alarm all operate normally.
To turn the button operation tone on and off
1. In the Edit Mode, use D to display the Button
On/Off status
Operation Tone selection screen.
2. Press A to toggle the button operation tone on (
OF
and off (
).
Minutes
Auto-repeat
Do this:
Use D (+) and B (–).
OF
Press D.
)
0:00
.
12/24-hour
)
Timekeeping (
)
00-second Animation
(
)
ON
)
2

Hide quick links:

Advertisement

loading

This manual is also suitable for:

Baby-g bg90-7bBaby-g bg90-4bBaby-g bg90-8bG-shock bg90-5b5000