Stopwatch - Casio Baby-G BG169R-2 Operation Manual

Operation Guide 3189/3252
Recalling Day Counter Data
In the Day Counter Mode, use D (+) and B (–) to scroll through the day counters.
To set the target date
1. In the Day Counter Mode, use D (+) and B (–) to
display the day counter you want to set.
2. Hold down A until the flashing cursor appears in the
text area. This indicates the input screen.
3. Press C to move the flashing in the sequence shown
below.
1st digit
Day
E-20
6. After you make the settings you want, press A to exit the input screen.
• The date can be set within the range of January 1, 1950 to December 31, 2049.
• The text area display can show only three characters at a time. Longer text scrolls
continuously from right to left. The symbol "
left is the last, and the character to the right is first.
E-22
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm screens until the one whose
time you want to set is displayed.
Alarm 1 Alarm 2
:00 (Hourly Time Signal)
• To set a one-time alarm, display one of the screens indicated by an alarm number
x1 x5
from through .
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
E-24
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press B to toggle it on (the alarm on indicator
Alarm on indicator
displayed) and off (the alarm on indicator not
displayed).
• Turning on a daily alarm (
alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that is currently turned on.
E-26

Stopwatch

The stopwatch lets you measure elapsed time, split times,
Mode indicator
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
Hours : Minutes
on the display clears the split time and returns to
Seconds
elapsed time measurement.
• All of the operations in this section are performed in the
1/100 second
Stopwatch Mode, which you enter by pressing C (page
E-5).
E-28
Press .
8th digit
Month Year
" indicates that the character to the
Alarm 3 Alarm 4
Alarm 5
x1 x5
through ) displays the
4. While the cursor is in the text area, use D and B to scroll through characters at
the current cursor position. Characters scroll in the sequence shown below. Holding
down D or B scrolls at high speed.
Press .
(Space)
A to Z 0 to 9
Press .
5. While the cursor is in the date area, press D and B to scroll through digits at the
current cursor position. Holding down D or B scrolls at high speed.
• Press B and D at the same time, and the message "CLR" will appear in the
display. The characters in the text area are cleared and today's date is set as the
target date. You then can make any changes in the date you want.
Alarms
You can set five independent Daily Alarms. When an
Mode indicator
alarm is turned on, the alarm tone sounds when the alarm
time is reached.
Alarm on
indicator
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are six screens in the Alarm Mode. Five are for
daily alarms (indicated by numbers from
x5
), and one is for the Hourly Time Signal (indicated by
).
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
Alarm time
E-5).
(Hour : Minutes)
Alarm number
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
• To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal ( ).
Hourly time
2. Press B to toggle it on (the hourly time signal on
signal on indicator
indicator displayed) and off (the hourly time signal on
indicator not displayed).
• The Hourly Time Signal on indicator is shown on the
display in all modes while the Hourly Time Signal is
turned on.
Elapsed time measurement
Start Stop Re-start
Split time measurement
Start Split Split release
(SPL displayed)
Split time and 1st-2nd place times
Split Stop
Start
First runner Second runner
finishes. finishes.
Display time of
first runner.
. (Period) - (Hyphen)
E-21
x1
through
E-23
E-25
E-27
Stop Clear
Stop Clear
Split release Clear
Display time of
second runner.
E-29