ARH ParkIT Install Manual
  1. Manuals
  2. Brands
  3. ARH Manuals
  4. IP Camera
  5. PARKIT
  6. Install manual

ARH ParkIT Install Manual

Hide thumbs Also See for ParkIT:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ParkIT and is the answer not in the manual?

Questions and answers

Related Manuals for ARH ParkIT

Summary of Contents for ARH ParkIT

  • Page 2: Table Of Contents

    ParkIT Install Guide For versions from 3.1 Document version: 13.08.16 Table of Contents Compliances ................................3 1. Hardware Overview.............................4 2. Install the Bracket..............................6 2.1 Mounting ..............................7 3. Setting up the Camera............................7 3.1 Power / Trigger/ Serial Connection ........................7 3.2 Ethernet Connection.............................8 4.

  • Page 3: Compliances

    Declaration of RoHS Compliance for Electrical and Electronic Products: ARH Inc. ("the Company") hereby declares that the ParkIT ANPR camera family placed on the European Community market by the Company after 1st July 2006 are compliant with EC Directive 2002/95/EC on the Restrict of Certain Hazardous Substances in Electrical and Electronic Equipment (commonly known as the EU RoHS Directive.)

  • Page 4: Hardware Overview

    1. Hardware Overview Sunshield Wall bracket Camera with bracket Infrared LEDs Camera optics Infrared LEDs Foot Cover Head Green status LED Light sensor Red status LED Camera front Bracket Page 4/15 Page 4/15 ParkIT Install Guide...
  • Page 5 Bracket Details and Sizes Page 5/15 Page 5/15 ParkIT Install Guide...

  • Page 6: Install The Bracket

    1. Remove the four screws (1) located at the back of the foot. (Use size 4 Allen key). 2. Rotate the foot (2) by 180 degrees. 3. Place the screws back into the holes and screw them back on. NOTE: Do not overtighten the screws. Page 6/15 Page 6/15 ParkIT Install Guide...

  • Page 7: Mounting

    12V nominal (11V..15V), reverse polarity protected DC Input Power 1.0A 1.1A Input Current (max. 2.5A transients occur for a few msecs) (max. 2.5A transients occur for a few msecs) Over-current by fuse Protection Page 7/15 Page 7/15 ParkIT Install Guide...

  • Page 8: Ethernet Connection

    The camera is equipped with CAT5e UTP crossover cable with RJ45 plug. It is ready to connect both to PC and network switch directly. NOTE: The RJ45 plug is not weatherproof. 4. Software Requirements The ParkIT camera is developed to operate without any kind of special software. Software requirements  For network setup, administrator (root) privileges are necessary.

  • Page 9: Accessing The Camera

    . Start a browser then enter the default IP address of the camera into the address bar (http://192.0.2.3). After this, the camera starts with administrator privileges, ready to be set up and configured. NOTE: To enable all camera functions, enable JavaScript and ActiveX controls in your browse Page 9/15 Page 9/15 ParkIT Install Guide...

  • Page 10: Recommended Camera Position

    (since they are more calligraphic than Latin characters). Too large characters are also not suitable for ANPR, therefore try to avoid settings where the character size is greater than 50 pixels in height. A line width of a character on the image should be at least 2 pixels. Page 10/15 Page 10/15 ParkIT Install Guide...
  • Page 11 A properly set camera should provide a similar image: A proper sample image Proper character sizes (in pixels) on the sample image Page 11/15 Page 11/15 ParkIT Install Guide...

  • Page 12: Maintenance / Storage

    The cameras should be stored in low humidity environment in the temperature range of -35 °C – +55 °C. NOTE: The startup temperature of the camera is -20 °C. Page 12/15 Page 12/15 ParkIT Install Guide...

  • Page 13: Appendix

    2. Enter the ifconfig command to see the reserved Ethernets (e.g. eth0). 3. Enter the following command: ifconfig ethY 192.0.2.25 where Y is a free eth (e.g. eth1) and 192.0.2.25 is a sample IP address. Page 13/15 Page 13/15 ParkIT Install Guide...
  • Page 14 Position of the sticker The sticker, indicating the Name, IP address, MAC address and the Serial Number of the camera, can be found on the bottom of the device. Page 14/15 Page 14/15 ParkIT Install Guide...

  • Page 15: Contact Information

    Contact Information Should you have any problem during operating the ParkIT cameras, our support team is at your disposal. Please try to explain the problem as detailed as possible and do not forget to send the following information to make it easier to help you: ...

Table of Contents