Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ARH FreewayCAM
Summary of Contents for ARH FreewayCAM
-
Page 2: Table Of Contents
FreewayCAM Install Guide For versions from 3.1 Document version: 13.08.16 Table of Contents Compliances ................................3 1. Hardware Overview.............................4 1.1 Bracket Details and Sizes ..........................5 2. Install the Hardware ............................6 2.1 Mounting ..............................6 3. Connect the Cables .............................7 3.1 Cable Layouts ...............................9 4. -
Page 3: Compliances
Compliances CE Certificates: The ARH FreewayCAM ANPR digital camera family complies with the European CE requirements specified in the EMC Directive 89/336/EEC. The ANPR cameras conform to the following Product Specifications: Emission: EN 55022, EN 55024 Immunity: EN 61000-4-2, -3, -4, -5, -6, -8, -11 Declaration of RoHS Compliance for Electrical and Electronic Products: ARH Inc. -
Page 4: Hardware Overview
1. Hardware Overview Sunshield Light sensor Green status LED Red status LED Wall bracket Camera with bracket Camera optics Infrared LEDs behind the protecting plate Camera front Page 4/17 Page 4/17 Page 4/17 FreewayCAM Install Guide Page 4/17... -
Page 5: Bracket Details And Sizes
1.1 Bracket Details and Sizes Page 5/17 Page 5/17 Page 5/17 FreewayCAM Install Guide Page 5/17... -
Page 6: Install The Hardware
2. Install the Hardware Camera fastening screw NOTE: Remove protective film from the protecting plate (on the camera front) before using the FreewayCAM. Adjust the bracket 1. Loosen the camera fastening screw on the bottom of the bracket. (Use size 5 Allen key). -
Page 7: Connect The Cables
5. Illuminator connector 6. Power AC AC IMPORTANT: SEAL THE UNUSED CABLE ENDINGS (END SLEEVES) BEFORE CONNECTING TO POWER IN ORDER TO AVOID DAMAGES DUE TO SHORT CIRCUIT! Page 7/17 Page 7/17 Page 7/17 FreewayCAM Install Guide Page 7/17... - Page 8 2. Illuminator Control 1 3. Illuminator Control 2 4. Illuminator Control In+ Illuminator Control 3 5. Illuminator Control 3 Illuminator Control 2 6. AC Illuminator Control 1 7. Illuminator Control In – Page 8/17 Page 8/17 Page 8/17 FreewayCAM Install Guide Page 8/17...
-
Page 9: Cable Layouts
(max. 2.5A transients (max. 2.5A transients (max. 2.5A transients *without extra heating occur for a few msecs) occur for a few msecs) occur for a few msecs) by fuse Over-current Protection Page 9/17 Page 9/17 Page 9/17 FreewayCAM Install Guide Page 9/17... - Page 10 SERIAL CONNECTION SPECIFICATION: The serial port of the camera complies with the RS 232 standard. Route the cable according to the image to avoid collecting rainwater at the socket. Page 10/17 Page 10/17 Page 10/17 FreewayCAM Install Guide Page 10/17...
-
Page 11: Software Requirements
4. Software Requirements The FreewayCAM is developed to operate without any kind of special software. Software requirements: For network setup, administrator (root) privileges are necessary. Web browser: Mozilla Firefox 4, Internet Explorer 8, Google Chrome 14.X.X.X or later editions. If it is possible, update your browser (Firefox or Chrome) to the newest available version. -
Page 12: Recommended Camera Position
ANPR, therefore try to avoid settings where the character size is greater than 50 pixels in height. A line width of a character on the image should be at least 2 pixels. Page 12/17 Page 12/17 Page 12/17 FreewayCAM Install Guide Page 12/17... - Page 13 A properly set camera should provide a similar image: A proper sample image Proper character sizes (in pixels) on the sample image Page 13/17 Page 13/17 Page 13/17 FreewayCAM Install Guide Page 13/17...
-
Page 14: Maintenance / Storage
The cameras should be stored in low humidity environment in temperature range of -35 °C to + 55 °C. Always use the sealing caps on the connectors to keep the camera unit waterproof! If you miss to use it, the warranty will be void! Page 14/17 Page 14/17 Page 14/17 FreewayCAM Install Guide Page 14/17... -
Page 15: Appendix
2. Enter the ifconfig command to see the reserved Ethernets (e.g. eth0). 3. Enter the following command: ifconfig ethY 192.0.2.25 where Y is a free eth (e.g. eth1) and 192.0.2.25 is a sample IP address. Page 15/17 Page 15/17 Page 15/17 FreewayCAM Install Guide Page 15/17... - Page 16 Position of the sticker The sticker, indicating the Name, IP address, MAC address and the Serial Number of the camera, can be found on the back of the device, under the sunshield. Page 16/17 Page 16/17 Page 16/17 FreewayCAM Install Guide Page 16/17...
-
Page 17: Contact Information
Contact Information Should you have any problem during operating the FreewayCAM cameras, our support team is at your disposal. Please try to explain the problem as detailed as possible and do not forget to send the following information to make it easier to help you: ...
Need help?
Do you have a question about the FreewayCAM and is the answer not in the manual?
Questions and answers