Realtime AN-IPEL-M80F-IRW1 Quick Start Manual

Realtime AN-IPEL-M80F-IRW1 Quick Start Manual

Hd ir quad lens panoramic network camera

Advertisement

HD IR Quad Lens Panoramic
Network Camera
Quick Start Guide

Table Of Contents

Features and Specifications
A.
Overview
Camera Installation
A.
Installation Steps
location
Quick Configuration Tool
A.
Overview
Web Operation
Appendices
C.
FAQ
www.icrealtime.com
IMPORTANT SAFEGUARDS AND WARNINGS
Electrical Safety
All installation and operation here should conform to your local electrical safety codes. The
power shall conform to the requirement in the SELV (Safety Extra Low Voltage) This series
product supports 12V DC, 24V AC and PoE. Please note: Do not connect these two power
supplying sources to the device at the same time; it may result in device damage! We assume
no liability or responsibility for all the fires or electrical shock caused by improper handling or
installation. We are not liable for any problems caused by unauthorized modification or
attempted repair.
Transportation Security
Care must be given to avoid heavy stress, violent vibration or water damage during
transportation, storage and installation.
Installation
Do not apply power to the camera before completing installation. Please install the proper
power cut-off device during the installation connection. Always follow the instruction guide the
manufacturer recommended.
Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are
not liable for any problems caused by unauthorized modifications or attempted repair.
2
Environment
2
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc. Please keep it away from the electromagnetic
radiation object and environment. Please make sure the CCD (CMOS) component is out of the
3
radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component
4
damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into
the camera. Lightning-proof device is recommended to be adopted to better prevent lightning
4
damage. The grounding studs of the product are recommended to be grounded to further
5
enhance the reliability of the camera.
Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily
maintenance work. Do not touch the CCD (CMOS) optic component. You can use the blower to
5
clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is
5-6
too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect
the CCD (CMOS) component when you do not use the camera.
7
7-8
Accessories
Be sure to use all the accessories recommended by manufacturer. Before installation, please
open the package and check all the components are included. Contact your local retailer ASAP
9
if something is broken in your package.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AN-IPEL-M80F-IRW1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Realtime AN-IPEL-M80F-IRW1

  • Page 1: Table Of Contents

    IMPORTANT SAFEGUARDS AND WARNINGS Electrical Safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) This series product supports 12V DC, 24V AC and PoE. Please note: Do not connect these two power supplying sources to the device at the same time;...
  • Page 2: Camera Interface

    It can be used standalone or with a network video recorder. If used standalone, it is able to utilize IC Realtime’s software suite including Smart ICRSS, IC View and ICRSS Pro. This model also supports IC Realtime’s P2P connection which allows easy remote connection.
  • Page 3 2A. INSTALLATION STEPS Step 1 Measure and drill out the mounting holes and cable exit, if Step 3 Thread in the collar adapter and secure with locking screw as shown in. Figure 2-3. necessary. Install the anchor screws into the mounting holes. See Figure 2-1 Figure 2-3 Step 4 Thread the cabling through the collar and base.
  • Page 4: Lens Adjustment

    2B. Lens Adjustment (available in some models) 2C. Waterproofing Connectors For outdoor installations, waterproofing with the included connectors Locate the adjustment knobs as shown in Figure 2-5. is necessary. See Figure 2-6 for installation steps. Figure 2-5 Figure 2-6 www.icrealtime.com...
  • Page 5: Factory Reset And Sd Card

    2D. RESTORE FACTORY DEFAULTS AND SD CARD INSTALLATION 3A. OVERVIEW Make sure the device is powered when attempting to press The IP Config tool is used to search the local network for IC Realtime Important: RESET button. devices as well as modify the IP addresses and upgrading firmware.
  • Page 6 Select “Search Setting” to modify the IP range to scan for and input To modify the device IP address, select one of the devices from the the correct login information for the device. See Figure 3-2. list and then click the pencil icon. The dialog box to modify the IP information will populate.
  • Page 7: Network Connection

    This series network camera product supports the Web access and The login interface is shown as below. See Figure 4-2. management via PC. Note: If it is your first time logging into the camera (and it has not been initialized through the ConfigTool or NVR), the camera will need 4A.
  • Page 8 Web GUI includes several modules: monitor channel preview, system configuration, alarm and etc. See Figure 4-3. Live: Live video of camera ● Playback: View recording from SD card (if applicable) ● Setting: For configuration changes. ● Alarm: For monitoring alarm triggers (motion detect, IVS, ●...
  • Page 9 5A. FAQ Check whether the power supply is ● properly connected. No image after the Check recorder video format and ● resolution compatibility with Camera Device is powered on Check whether the main power and ● transformer are working normally. Use the required power supply.

Table of Contents