Related Manuals for Worldwide Construction And Forestry Division 27C ZTS
Summary of Contents for Worldwide Construction And Forestry Division 27C ZTS
- Page 1 27C ZTS and 35C ZTS Excavator Operation and Tests TECHNICAL MANUAL 27C ZTS and 35C ZTS Excavator Operation and Tests TM2052 17JUL18 (ENGLISH) Worldwide Construction And Forestry Division PRINTED IN U.S.A.
- Page 2 Operation and tests sections help you of troubleshooting, general maintenance, and basic type identify the majority of routine failures quickly. of failures and their causes. DX,TMIFC -19-15APR14-1/1 TM2052 (17JUL18) 27C ZTS and 35C ZTS Operation & Tests 071718 PN=2...
- Page 3 18600 South John Deere Road Attn: Publications, Dept. 324 Dubuque, IA 52004-0538 FAX NUMBER: 1-563-589-5800 (USA) Publication Number: Page Number: Ideas, Comments: Name: Phone: Email Address: THANK YOU! TX,TM,FAX -19-03JUL01-1/1 TM2052 (17JUL18) 27C ZTS and 35C ZTS Operation & Tests 071718 PN=3...
- Page 4 Introduction TM2052 (17JUL18) 27C ZTS and 35C ZTS Operation & Tests 071718 PN=4...
-
Page 5: Group 01-Safety
The right is reserved to make changes at any time without notice. COPYRIGHT © 2018 DEERE & COMPANY Moline, Illinois All rights reserved. A John Deere ILLUSTRUCTION ™ Manual Previous Editions Copyright © 2002, 2006,2012, 2014 TM2052 (17JUL18) 27C ZTS and 35C ZTS Operation & Tests 071718 PN=1... - Page 6 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...
- Page 7 Contents TM2052 (17JUL18) 27C ZTS and 35C ZTS Operation & Tests 071718 PN=2...
-
Page 8: Table Of Contents
Safely............. 9000-01-9 Service Cooling System Safely ....9000-01-9 Remove Paint Before Welding Or Heating ..........9000-01-9 Make Welding Repairs Safely ....9000-01-10 Drive Metal Pins Safely ......9000-01-10 TM2052 (17JUL18) 9000-1 27C ZTS and 35C ZTS Operation & Tests 071718 PN=1... - Page 9 Contents TM2052 (17JUL18) 9000-2 27C ZTS and 35C ZTS Operation & Tests 071718 PN=2...
-
Page 10: Recognize Safety Information
Know and observe all safety rules that may apply to every Operator should be familiar with the job site and work situation and work site. surroundings before operating. Try all controls and TX03679,00016FA -19-03JAN07-1/1 TM2052 (17JUL18) 9000-01-1 27C ZTS and 35C ZTS Operation & Tests 071718 PN=9... -
Page 11: Wear Protective Equipment
Keep all guards and shields in good condition and properly installed. Fix damage and replace worn or broken parts immediately. Pay special attention to hydraulic hoses and electrical wiring. TX03679,0001734 -19-17DEC14-1/1 TM2052 (17JUL18) 9000-01-2 27C ZTS and 35C ZTS Operation & Tests 071718 PN=10... -
Page 12: Stay Clear Of Moving Parts
If you must operate in an enclosed space, provide adequate ventilation. Use an exhaust pipe extension to remove the exhaust fumes or open doors and windows to bring outside air into the area. TX03679,00016D4 -19-03NOV08-1/1 TM2052 (17JUL18) 9000-01-3 27C ZTS and 35C ZTS Operation & Tests 071718 PN=11... -
Page 13: Prevent Fires
Safety Data Sheet (MSDS). The MSDS describes physical and health hazards, safe use procedures, and emergency response techniques for chemical substances. Follow MSDS recommendations to handle chemical products safely. TX03679,00016D7 -19-31JAN07-1/1 TM2052 (17JUL18) 9000-01-4 27C ZTS and 35C ZTS Operation & Tests 071718 PN=12... -
Page 14: Dispose Of Waste Properly
Never attempt to start engine from the ground. Do not attempt to start engine by shorting across the starter solenoid terminals. TX03679,0001799 -19-22APR10-1/1 TM2052 (17JUL18) 9000-01-5 27C ZTS and 35C ZTS Operation & Tests 071718 PN=13... -
Page 15: Use And Maintain Seat Belt
At high speeds hitting obstacles (rocks, uneven concrete or manholes) can cause a sudden stop. Always wear your seat belt. TX14740,0001E9F -19-30JUN10-1/1 TM2052 (17JUL18) 9000-01-6 27C ZTS and 35C ZTS Operation & Tests 071718 PN=14... -
Page 16: Keep Riders Off Machine
Use a signal person when backing if view is obstructed or when in close quarters. Keep signal person in view at all times. Use prearranged hand signals to communicate. TX14740,0001E7B -19-19MAR02-1/1 TM2052 (17JUL18) 9000-01-7 27C ZTS and 35C ZTS Operation & Tests 071718 PN=15... -
Page 17: Avoid Machine Tip Over
Ensure that a qualified person is involved in attachment installation. Add guards to machine if operator protection TX03679,00016F0 -19-12FEB07-1/1 TM2052 (17JUL18) 9000-01-8 27C ZTS and 35C ZTS Operation & Tests 071718 PN=16... -
Page 18: Park And Prepare For Service Safely
15 minutes before welding or heating. Work outside or in a well-ventilated area. Dispose of waste, paint and solvents properly. TX03679,0001732 -19-06SEP00-1/1 TM2052 (17JUL18) 9000-01-9 27C ZTS and 35C ZTS Operation & Tests 071718 PN=17... -
Page 19: Make Welding Repairs Safely
Hammering hardened metal parts such as pins and bucket teeth may dislodge chips at high velocity. Use a soft hammer or a brass bar between hammer and object to prevent chipping. TX03679,0001745 -19-03JAN07-1/1 TM2052 (17JUL18) 9000-01-10 27C ZTS and 35C ZTS Operation & Tests 071718 PN=18... - Page 20 Section 9005 Operational Checkout Procedure Contents Page Group 10—Operational Checkout Procedure Operational Checkout........9005-10-1 Operator Station Checks—Key Switch On, Engine Off ........9005-10-1 Operational Checks—Engine On ............9005-10-6 TM2052 (17JUL18) 9005-1 27C ZTS and 35C ZTS Operation & Tests 071718 PN=1...
- Page 21 Contents TM2052 (17JUL18) 9005-2 27C ZTS and 35C ZTS Operation & Tests 071718 PN=2...
- Page 22 F10 Monitor Controller And Display 5 Amp fuse. (Group 9015-20.) Check and replace bulb if any bulb fails to come on. Continued on next page CED,OUOE003,1506 -19-10DEC12-3/30 TM2052 (17JUL18) 9005-10-1 27C ZTS and 35C ZTS Operation & Tests 071718 PN=21...
- Page 23 Does each lever return to neutral at the same time when released? NO: Repair or replace pilot controller. Go to Propel Pilot Controller Repair. (Group 3360.) Continued on next page CED,OUOE003,1506 -19-10DEC12-5/30 TM2052 (17JUL18) 9005-10-2 27C ZTS and 35C ZTS Operation & Tests 071718 PN=22...