Sealey SAC10030VE.V2 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist. If the product is used in the course of business duties, it
must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
ELECTRICAL SAFETY INFORMATION It is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable and DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by
8
a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
IMPORTANT! The use of extension leads to connect these compressors to the mains is not
recommended as the resulting voltage drop reduces motor, and therefore pump performances.
1.2. GENERAL SAFETY
Familiarise yourself with the application and limitations of the compressor.
9
Ensure the compressor is in good order and condition before use. If in any doubt DO NOT use the unit and contact an electrician/
9
service agent.
WARNING! Compressor must only be serviced by an authorised agent. DO NOT tamper with, or attempt to adjust, pressure
‰
switch or safety valve.
Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air tank pressure has been vented.
9
Maintain the compressor in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may
9
be dangerous and will invalidate your warranty.
Read the instructions relating to any accessory to be used with the compressor. Ensure the safe working pressure of any air
9
appliance used exceeds unit's output pressure. If using spray gun, check that the area selected for spraying is provided with air change
system/ventilation.
Ensure the air supply valve is turned off before disconnecting the air supply hose.
9
To move the compressor use the handle only. Maintain unit's centre of gravity when lifting. DO NOT attempt to lift or move the
9
compressor by any other means.
Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
9
Keep tools and other items away from the compressor when it is in use, and keep the area clean and clear of unnecessary items.
9
Ensure any air hose attached is not tangled, twisted or pinched.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT dis-assemble compressor for any reason. The unit must be checked by qualified personnel only.
8
DO NOT use the compressor outdoors, in damp or wet locations or operate within the vicinity of flammable liquids, gases or solids.
8
DO NOT touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot and will remain so for some time
8
after shut down.
DO NOT attempt to move the compressor by pulling the air tool hose.
8
DO NOT use this product to perform a task for which it is not designed.
8
DO NOT deface the certification plate attached to the compressor tank
8
DO NOT cover the compressor or restrict air flow around the machine whilst operating.
8
© Jack Sealey Limited
100L V-TWIN DIRECT DRIVE COMPRESSOR 3HP
MODEL NO:
Wear ear WARNING: Ensure oil level
protection High Voltage is correct before
Original Language Version
SAC10030VE.V2
WARNING: WARNING:
Hot surface Automatic
first use start up
Indoor use only DO NOT open
the air cock
before an air
hose is attached
RECOMMENDED
FUSE RATING:
13AMP
SAC10030VE.V2 Issue 2 (7) 24/06/20