UNI-T UT305S User Manual

P/N:110401109910X
UT305S
Infrared Thermometer User Manual
Overview
UT305S is a high-accuracy, high-D:S ratio (50:1), wide range (-50°C~2000 °C ), high repeatability, durable and
easy-to-operate infrared thermometer (hereinafter referred to as the thermometer) designed according to the
user's field needs. The thermometer can quickly and accurately determine the surface temperature of the target
by measuring the infrared energy radiated by the target surface, which is suitable for non-contact temperature
measurement.
Safety Instructions
Warning:
In order to prevent eye damage or personal injury, please read the following safety instructions before using the
product:
1. Do not point the laser directly at persons or animals or indirectly through reflective surfaces.
2. Do not look directly at the laser or with optical tools (binoculars, microscopes, etc.).
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
λ=630-670nm,<1mW, EN60825-1:2014
Caution:
If the laser irradiates the user's eyes, please close the eyes immediately and turn the head away.
Do not disassemble or refit the product and laser without permission.
To ensure its safety and accuracy, this product should only be repaired by professional maintenance personnel
using original replacement parts.
Replace the batteries when the low battery indicator shows to prevent incorrect measurements.
Please check the product before using it. If it is damaged, cracked on the surface or missing plastic parts, do
not use it.
Please refer to the emissivity information for the actual temperature. Highly reflective objects or transparent
materials will make the actual temperature higher than the measured temperature. When measuring these objects,
pay attention to the risk of burns.
Do not use the product in an environment with flammable and explosive liquid, gas or dust.
Do not use the product around the environment with steam, dust, or large temperature fluctuations. It may bring
inaccurate results and risks.
Put the product in the current environment for more than 30 minutes before using it to ensure measurement
accuracy.
Do not leave the thermometer on or near objects of high temperature.
Technical Indexes
Model UT305S
Optical resolution 50:1
Measurement range -50°C~2000 °C (-58°F~3632 )
LCD size 35*35mm
LCD display High-contrast color EBTN
-50 °C ~0 °C : ±(1.0 °C +0.1
0 °C ~2000 °C : ±1.0 °C or ±1.0% (take the larger value)
Accuracy
-58 ~32 : ±(2.0 +0.1 / ) °F °F °F
32 ~3632 : ±2.0 °F °F °F or ±1.0% (take the larger value)
±0.1 °C °C / or ±0.1%/ °C take the larger value
Temperature index
(±0.1°F/°F or ±0.1%/°F take the larger value)
0.5 °C or 0.5% take the larger value
Repeatability
(1.0°F or 0.5% take the larger value)
Emissivity 0.1~1.0 (adjustable, stores 5 sets of preset values)
Response time ≤250ms (95% of reading)
Spectral response 8μm~14μm
Auto power off
15s
Low battery indication
High/low temperature LED alarm
High/low temperature sound alarm
Data hold
Unit conversion ( °C °F / )
MAX/MIN/AVG/DIF
Lock measurement
Single laser, wavelength: 630nm~670nm, output power 1mW, type: class 2
Laser
Operating temperature
Storage temperature
Operating humidity
Drop proof
Battery type
Battery life 10 hours (continuous measurement mode with laser and backlight on)
Product color
Product weight
Product size
Safety Standards
CE certification: EN61326-1:2013; Safety standards of laser products: EN60825-1:2014
FDA: Class 2; IEC: Class 2
Reference Standard
JJG 856-2015
Characteristics
1) With single-laser and high-accuracy laser adjustment technology.
2) Bright, easy-to-read and high-contrast color EBTN display.
3) MAX/MIN/AVG/DIF hold.
4) Store 5 sets of preset values (high and low temperature alarm and emissivity) for quick setting.
5) With red, green and blue LED and buzzer sound alarm, can quickly find abnormalities.
6) Trigger lock, suitable for processes that require temperature monitoring.
7) Equipped with a tripod mounting hole.
Appearance
Laser
Infrared receiving window
1
Trigger
2
Battery cover
Tripod mounting hole
LCD display
3
SET button
MODE button
°F 4
Laser switch button
HI/LO button
Laser warning label
°C °C / )
LCD Indicators
°F °F
Trigger lock
Buzzer
Temperature measurement alarm
Low battery
Temperature measurement
Temperature hold
Temperature unit
Temperature main display
Temperature secondary display
Emissivity
Laser
Measurement mode
Startup and Shutdown
Startup
Short press (less than 0.5s) the trigger to turn on the thermometer, and the measured value before the last shutdown
will be displayed. Pressing MODE button can view MAX/MIN/AVG/DIF.
<
Shutdown
-5°C~50 °C (23°F~122 ) °F The thermometer will automatically shut down after 15 seconds without any operation in the HOLD mode, and save
the current measured value.
-20 °C ~60 °C (-4 ~140 ) °F °F
Manual Measurement
<90%RH (non-condensing)
1) After aiming at the measured object, press the trigger and hold it. When the SCAN symbol is flashing, it means
that the temperature is being measured, and the measurement result will be updated on the LCD.
1m
2) Release the trigger, the SCAN symbol will disappear while the HOLD symbol will be displayed. The thermometer
will stop measuring the temperature and keep the last measured value.
1*1604A 9V alkaline battery
Lock Measurement
1) When lock measurement is turned on, short pressing the trigger can trigger this function. The
Red + grey
displayed on the LCD and the SCAN symbol will flash. The thermometer will measure the target temperature
continuously without pressing the trigger all the time.
325g
2) Press the trigger again, the
179.00×126.50×53.00mm thermometer will stop measuring and keep the last measured temperature.
3) In the lock measurement setting interface, the user can set the lock measurement time (1m~5h). After the lock
function is triggered, the timing starts. When the set time is reached, the thermometer will automatically shut
down and save the last measured value. The user can view the measured value by short pressing (less than 0.5s)
the trigger (Caution: the measured value will be cleared if the user long presses the trigger). This operation is
suitable for processes that require regular temperature monitoring.
Caution: The measured target should be greater than 2 times the thermometer light spot diameter (S), and
then the test distance (D) can be determined according to the D: S relationship diagram.
MAX/MIN/AVG/DIF Value
Short press the "MODE" button to switch among "MAX→MIN→AVG→DIF" measurement modes in sequence, and
the temperature of the corresponding mode will be displayed in the secondary display position (as shown below).
Laser Indicator
6 11
5
Pressing the
7
10
display on the LCD, and the laser will accurately indicate the measured position.
8
Note: Please follow the cautions when turning on the laser to avoid eyes injury.
9
High/Low Temperature Alarm
Pressing the "HI/LO" button can turn on/off the high and low limit alarm function in sequence. The sequence is:
HI/LO limit alarm functions are turned on at the same time →HI limit alarm is turned on→LO limit alarm is turned on
→HI/LO limit alarm functions are turned off at the same time (as shown below).
When the HI alarm is turned on, if the measured temperature is higher than the set high alarm limit, the red LED
and the HI symbol on the display will flash. If the sound alarm is turned on, the buzzer will beep.
When the LO alarm is turned on, if the measured temperature is lower than the set low alarm limit, the blue LED
and the LO symbol will flash. If the sound alarm is turned on, the buzzer will beep.
When either HI/LO alarm is turned on, if the measured temperature value is within the range of high and low alarm
limit, the green LED and the OK symbol will flash.
Function Settings
In the HOLD interface, pressing the "SET" button can enter the high alarm limit→low alarm limit→emissivity→
temperature unit→sound alarm→lock measurement and other function settings. Under these setting interfaces,
the user can return to the HOLD interface by pressing the trigger or no operation for 10s.
High Alarm Limit Setting
In the HOLD interface, pressing the "SET" button once will enter the high alarm limit setting interface, and then
pressing the "
values, the user can use
pressing will add or subtract 1 to the value each time, and long pressing will add or subtract 10 each second.
and SCAN symbols will disappear while the HOLD symbol will appear. The
button can turn on/off the laser indication function. When it is turned on, the laser symbol
" button can quickly select the preset values (P1-P5). If there is no wanted value among the preset
" " ▼ or "▲" to adjust at any of the preset values that is closest to the wanted one. Short
symbol will be
will