Other Error Messages - Canon PIXMA MP810 Service Manual

6 times Internal temperature error
7 times Ink absorber full
8 times Print head temperature rise
error
9 times EEPROM error
10 times VH monitor error
11 times Carriage lift mechanism error
12 times AP position error
13 times Paper feed position error
14 times Paper feed cam sensor error
15 times USB Host VBUS overcurrent
16 times Pump roller sensor error
17 times Paper eject encoder error
19 times Ink tank position sensor error
20 times Other hardware error
22 times Scanner home position error
Power LED turned ROM / RAM error
off, and Alarm
LED lit
* Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or EEPROM information print). If the counter value
is 7% or more, also replace the ink absorber kit when replacing the logic board ass'y. If the counter value is less than 7%, register the current ink absorber
counter value to the replaced new logic board instead.

2-3. Other Error Messages

Message on the LCD
The selected paper cannot be fed from
cassette. Change the paper source and press
[OK].
Cannot specify the followings together.
Change one of the settings.
Device memory is full. Reduce the amount of
photos, films, copies to scan.
ASF after an error occurred in the ASF cam
sensor.
[5400] The internal temperature is not normal.
[5B00, The ink absorber is supposed to be full.
5B01] Message on the LCD:
Ink absorber full. Service required.
Error codes:
5B00: Main ink absorber is full (overseas).
5B01: Main ink absorber is full (Japan).
[5200] The print head temperature exceeded the specified
value.
[6800] A problem occurred in writing to the EEPROM.
[B200] The internal temperature exceeded the specified
value.
[5110] The carriage did not move up or down properly.
[6A00] An error occurred in the AP motor during purging
operation.
[6B00] An error occurred in the paper feed motor.
[6B10] An error occurred in the paper feed cam sensor
during paper feeding from the front paper feed
cassette.
[9000] The USB Host VBUS is overloaded.
[5C20] The pump roller position cannot be detected.
[6010] An error occurred in the paper eject encoder
signal.
[6502] None of the ink tank position is detected.
[6500] The PCI bus error is detected by the ASIC.
[5010] The scanner unit cannot detect the home position,
or the scanner unit warming-up is not performed
properly at power-on.
On the LCD, "Scanner is not operating correctly."
is displayed.
The check sum value is incorrect in the ROM
check or RAM check at hard-power-on.
[See 3-3. Adjustment / Settings, (6) Service mode, for details.]
Cause
The paper type being used (business card, Credit Card
size paper, or stickers, etc.) is not supported for paper
feeding from the cassette.
Settings made conflict each other.
The memory is not sufficient to do the print job.
1-6
- ASF_PE sensor board
*
- Logic board
*
- Logic board
- Ink absorber kit
- Print head
*
- Logic board
*
- Logic board
- Print head
- Carriage unit
*
- Logic board
- Sheet feed unit
- PR lift shaft ass'y
- Carriage lift sensor unit
*
- Logic board
- Sheet feed unit
- Purge unit
*
- Logic board
- Sheet feed unit
*
- Logic board
- Sheet feed unit
*
- Logic board
*
- Logic board
- Purge unit
*
- Logic board
- Platen unit
- Timing sensor unit
- Timing slit disk eject film
- Paper feed motor
*
- Logic board
- Platen unit
*
- Logic board
*
- Logic board
- Scanner unit
*
- Logic board
Solution
Change the paper source to the ASF.
Change the paper type to other than plain paper for
borderless printing, or change to bordered printing
with plain paper.
Reduce the amount of data to be printed, or print from
a computer.