Advertisement
Quick Links
USER MANUAL for USB 2.0 PCI Card
Features
Compliant with Universal Serial Bus Specification Revision 2.0 (Data Rate 1.5/12/480 Mbps)
Compliant with Open Host Controller Interface Specification for USB Rev 1.0a
Compliant with Enhanced Host Controller Interface Specification for USB Rev 0.95
PCI multi-function device consists of two OHCI Host Controller cores for full/low-speed signaling
and one EHCI Host Controller cores for high-speed signaling
32-bit 33 MHz host interface compliant to PCI Specification release 2.2
Supports PCI-Bus Power Management Interface Specification release 1.1
All downstream facing ports can handle high-speed (480 Mbps), full-speed (12 Mbps), and
low-speed (1.5 Mbps) transaction
Plug & Play and Hot Swapping functions
System Requirements
Windows 98/98SE/2000/ME/XP
Mac OS X 10.1
Hardware Installation for USB 2.0 PCI Card
1.
Turn off the power to your computer and any other connected peripheral devices. Follow the
precautions for static electricity discharge.
2.
Unplug the power cord from the back of the computer
3.
Remove the computer's cover.
4.
Select an available 32-bit PCI slot for the new board.
5.
Remove the selected slot bracket by unscrewing the holding screw and slide it out. Save this screw
for securing the USB 2.0 PCI card after it's installed.
6.
To install the USB 2.0 PCI card, carefully align the board's bus connector with the selected
expansion slot on the motherboard. Push the board down firmly, but gently, until it is well seated.
7.
Replace the slot bracket's holding screw to secure the board to the rear slot panel.
8.
Put back the computer's cover.
9.
Reconnect the power cord and make new connections to the ports.
Driver Installation for USB 2.0 PCI Card
Under Win 98 / 98SE
Under Win 2000 / ME / XP – page 6~13
Driver note: If you are installing from the included CD, the file you need to run is called
"U2v2_062.exe". If you are installing from a download, the file is called "U2v2_1_5.exe".
Windows XP users: please install Service Pack 1 before you install this card and software!
– page 2~5
1
Advertisement
Related Manuals for Cables to Go 39554
Summary of Contents for Cables to Go 39554
-
Page 1: System Requirements
Features Compliant with Universal Serial Bus Specification Revision 2.0 (Data Rate 1.5/12/480 Mbps) Compliant with Open Host Controller Interface Specification for USB Rev 1.0a Compliant with Enhanced Host Controller Interface Specification for USB Rev 0.95 PCI multi-function device consists of two OHCI Host Controller cores for full/low-speed signaling and one EHCI Host Controller cores for high-speed signaling 32-bit 33 MHz host interface compliant to PCI Specification release 2.2 Supports PCI-Bus Power Management Interface Specification release 1.1... - Page 2 Driver Installation Under Win 98 / 98SE Windows will detect new hardware and start the “NEC USB Open Host Controller” driver search program. As Figure 1. Click Next. Select “Search for the best driver for your device” in Figure 2. Click Next. Put your operating system CD in the CD-ROM.
-
Page 3: Figure 8 (The Dialog Is The Same As Figure
See Figure 5. Click Next again. After installation, click Finish. As Figure 6. As “NEC USB Open Host Controller” driver search program shows up. See Figure 7. Click Next. Select “Search for the best driver for your device (Recommended)”. Click Next. As Figure 8 (The dialog is the same as Figure 2) Figure 4 Figure 5... - Page 4 10. Don’t select any location, Click Next. See Figure 9. 11. Select “The updated driver (Recommended) NEC USB Open Host Controller”. As Figure 10. Click Next. 12. After installation, click Finish. As Figure 11. 13. As “PCI Universal Serial Bus” driver search program shows up.
- Page 5 USER MANUAL for USB 2.0 PCI Card Figure 12...
- Page 6 14. Double click the “Explore” under “My Computer” as Figure13 15. Find the file located in “G:\NEC_USB2.0 PCI Card\PC\U2v2_062” and double click. As Figure 14 16. Select “Yes, I want to restart my computer” and click Close. As Figure 15 17.
- Page 7 Driver Installation Under Win 2000 See the welcome page,as Figure 1.Click Next Select “Search for a suitable driver for my device (recommended), as Figure 2.Click Next Don’t select any location and click Next, as Figure 3. Figure 1 Figure 2 Figure 3...
- Page 8 Select “Disable the device” and click Finish. As Figure 4 Double click the “Explore” under “My Computer” as Figure 5 Find the file located in “G:\NEC_USB2.0 PCI Card\PC\U2v2_062” and double click. As Figure 6 Select “Yes, I want to restart my computer” and click Close.
- Page 9 USER MANUAL for USB 2.0 PCI Card See Figure 8. Check if the “NEC PCI to USB Enhanced Host Controller” is installed. Figure 8...
- Page 10 Driver Installation Under Win ME 1. Select “Automatically search for a better driver (Recommended)”. Click Next. As Figure 1 2. Click Finish As Figure 2 Double click the “Explore” under “My Computer” As Figure 3 Find the file located in “G:\NEC_USB2.0 PCI Card\PC\U2v2_062”...
- Page 11 Select “Yes, I want to restart my computer” and click Close. As Figure 5 See Figure 6. Check if the “NEC PCI to USB Enhanced Host Controller” is installed. Figure 5 Figure 6...
- Page 12 Driver Installation Under Win XP 1. Select “install the software automatically (Recommended)”. Click Cancel. As Figure 1 Double click “Explore” under “My Computer” As Figure 2. Find the file located in “G:\NEC_USB2.0 PCI Card\PC\U2V2_064” As Figure 3 4. Click “Continue Anyway” As Figure 4 Figure 1 Figure 2 Figure 3...
- Page 13 Select “Yes, I want to restart my computer” and click Close. As Figure 5 Select “install the software automatically (Recommended)”. Click Next. As Figure 6 Click Continue Anyway. As Figure 7 8. “USB2.0 Root Hub Device” has been installed. Click Finish, as Figure 8 Figure 5 Figure 6 Figure 7...
- Page 14 USER MANUAL for USB 2.0 PCI Card 9 See Figure 9. Check if the “NEC PCI to USB Enhanced Host Controller” is installed. Figure 9...