Sealey SA7T Instructions

Item Part No. Description
1 SA7T/01 Hex. Screw
2 SA7T/02 Flat Washer
3 SA7T/03 Wave Washer
4 SA7T/04 Balance Nut
5 SA7T/05 Spacer
6 SA7T/06 Washer
7 SA7T/07 Hex. Nut
8 SA7T/08 6” Sanding Pad
9 SA7T/09 Retaining Ring
10 SA7T/10 Wave Washer
11 SA7T/11 Pad Mounting Shaft
12 SA7T/12 Bearing
13 SA7T/13 Wave Washer
14 SA7T/14 Hex. Nut
15 SA7T/15 Random Balance Body
16 SA7T/16 Hex. Screw
16P SA7T/16P Washer
17 SA7T/17 Rotor Shaft
18 SA7T/18 Key
19 SA7T/19 Wave Washer
20 SA7T/20 Bearing
21 SA7T/21 End Plate
22 SA7T/22 Rotor
23 SA7T/23 Rotor Blade
24 SA7T/24 Cylinder
25 SA7T/25 Pin
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
Original Date: 141200
Issue Date: 291200
Version No: 1
Date Modified: N/A
Item Part No. Description
26 SA7T/26 O-Ring
27 SA7T/27 Retaining Ring
28 SA7T/28 Cap Screw
29 SA7T/29 Cap Screw
30 SA7T/30 Motor Cover
30P SA7T/30P Finger Cover
31 SA7T/31 Motor Gasket
32 SA7T/32 Motor Housing
33 SA7T/33 Plastic Cover
34 SA7T/34 Air Regulator
35 SA7T/35 O-Ring
36 SA7T/36 Retaining Ring
37 SA7T/37 Spring
38 SA7T/38 Valve Ball
39 SA7T/39 Valve
40 SA7T/40 O-Ring
41 SA7T/41 O-Ring
42 SA7T/42 Valve Bushing
43 SA7T/43 Bracket
44 SA7T/44 Screw
45 SA7T/45 Hex. Nut
46 SA7T/46 Screw Washer
47 SA7T/47 Set Screw Nut
48 SA7T/48 Lever
49 SA7T/49 Handle Cover
50 SA7T/50 Inlet Bushing
E-mail: sales@sealey.co.uk
01284 703534
Web: www.sealey.co.uk
INSTRUCTIONS FOR:
RANDOM ORBITAL SANDER
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
F
when using this equipment.
WARNING! Disconnect from air supply before changing accessories or servicing.
F
Maintain the sander in good condition (use an authorised service agent).
!
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
!
invalidate the warranty.
Use in a suitable, clean and tidy work area, free from unrelated materials. Ensure there is adequate lighting.
!
Before each use check abrasive pads for condition. If worn or damaged replace immediately.
!
Ensure the abrasive pad RPM rating is the same as, or greater than, the RPM rating of the sander.
!
Ensure there are no flammable or combustible materials near the work area.
!
WARNING! Always wear approved eye or face and hand protection when operating the sander.
F
Use face, dust, or respiratory protection in accordance with COSHH regulations.
!
Depending on the task, sander noise level may exceed 85dB in which case wear safety ear defenders.
!
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
!
Wear appropriate protective clothing and keep hands and body clear of working parts.
!
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
!
Keep children and unauthorised persons away from the working area.
!
Check moving parts alignment on a regular basis.
!
Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
!
Avoid unintentional starting.
!
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
F
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
!
that all connections are secure.
Prolonged exposure to vibration from this sander poses a health risk. It is the owner’s responsibility to correctly
!
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the sander for a task it is not designed to perform.
%
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
%
DO NOT use cloth backed sanding pads. Use only appropriate paper adhesive pads, following pad instructions.
%
WARNING! DO NOT sand any materials containing asbestos.
F
DO NOT carry the sander by the hose, or yank the hose from the air supply.
%
DO NOT force, or apply heavy pressure to the sander, let the sander do the work.
%
DO NOT place air line attachments close to your face and do not point the air line at other persons or animals.
%
DO NOT operate sander when you are tired, under the influence of alcohol, drugs or intoxicating medication
%
DO NOT use sander where there are flammable liquids, solids or gases, such as paint solvents and
%
including waste wiping or cleaning rags etc.
DO NOT carry the sander with your finger on the power lever.
%
DO NOT direct air from the air hose at yourself or others.
%
When not in use disconnect from air supply and store in a safe, dry, childproof location.
!
SA7T
Model:
.
SA7T - 3 - 170902