Subscribe to Our Youtube Channel
Related Manuals for Envirco IsoClean CM
Summary of Contents for Envirco IsoClean CM
- Page 1 IsoClean ® HEPA Filtration Systems INSTALLATION, OPERATION, AND MAINTENANCE MANUAL ENVIRCO Technical Support: 800-884-0002...
-
Page 2: Table Of Contents
Installation ........................4 Operation .......................... 4 Maintenance & Service..................... 5 Troubleshooting ........................ 9 Wiring Diagram ......................... 9 Specifications ........................10 Replacement Parts ......................10 Air Change Rates ......................10 Limited Warranty ......................11 Contact Envirco ........................11 Innovators in Clean Air Technology | www.envirco.com... -
Page 3: Introduction
• Addiction Recovery Centers • Temporary Medical Facilities Anti-microbial Options Prefilter • UV-C Sanitizing Light • Carbon Prefilter (Sold Separately) • 100% Exhaust Duct Collar (Sold Separately) • Directional Discharge Kit (Sold Separately) Innovators in Clean Air Technology | www.envirco.com... -
Page 4: Installation
Cut the wrapping and remove the carboard. Again inspect for any noticeable damage to the unit. The shipping components list and actual material received should be compared and any shortages reported to Envirco immediately. Lift the IsoClean® CM off the shipping pallet. Move the unit to the desired location. -
Page 5: Maintenance & Service
■ Maintenance & Service Parts Identification Motor/blower UV-C Light (optional) HEPA Filter Anti-microbial Prefilter Air Inlet Innovators in Clean Air Technology | www.envirco.com... - Page 6 To replace the HEPA filter, please reference the directions for removing the front panel before removing the HEPA filter. Innovators in Clean Air Technology | www.envirco.com...
- Page 7 IsoClean ® HEPA Filtration System I n s t a l l a t i o n , O p e r a t i o n , & M a i n t e n a n c e M a n u a l Once the power is off and the front panel is off, it is recommended to remove the UV bulb from the UV light assembly before removing the HEPA filter.
- Page 8 Take care when at the edge of the channel to support the weight of the motor/blower assembly. Note: The motor/ blower weighs approximately 35 lbs. To replace, reverse the order of removal. Innovators in Clean Air Technology | www.envirco.com...
-
Page 9: Troubleshooting
IsoClean ® HEPA Filtration System I n s t a l l a t i o n , O p e r a t i o n , & M a i n t e n a n c e M a n u a l ■... -
Page 10: Specifications
(12800 ft 10 ACH 7 ACH 5 ACH 4 ACH 3 ACH 2 ACH 1 ACH 400 CFM 42 ACH 31 ACH 22 ACH 17 ACH 14 ACH 10 ACH 7 ACH 1,700 CFM Innovators in Clean Air Technology | www.envirco.com... -
Page 11: Limited Warranty
Contact Envirco ■ For warranties, replacement parts, technical support, or any other questions please contact Envirco at 1-800-884-0002. For tech support related issues including troubleshooting and warranty, please email techsupport@envirco.com. For customer service related issues inlcuding parts ordering, please email customerservice@envirco.com. - Page 12 DCM & RSR » AC or DC Control Systems Envirco USA 101 McNeill Road | Sanford, NC 27330, USA tel: 919.775.2201 | toll free: 800.884.0002 | fax:800.458.2379 www.envirco.com | customerservice@envirco.com or techsupport@envirco.com Copyright ©2013 Envirco. All Rights Reserved. Form P/N#: 267426...
Need help?
Do you have a question about the IsoClean CM and is the answer not in the manual?
Questions and answers