Summary of Contents for Bossard BST-BC-2830
- Page 1 Operating instructions Single charger BST-BC-2830(-USA) NOTE In case of doubt, the original German version of the operating instructions applies.
-
Page 2: Table Of Contents
Table of contents 1 Basic information Purpose of this document Intended use 1.2.1 Improper use Warranty and liability Structure of the warnings Copyright 2 Basic safety information Information contained in this document Owner responsibilities 2.2.1 Personnel responsibilities 2.2.2 Personnel training Electrical hazards 2.3.1 Basic safety measures (must always be observed!) 2.3.2 Observing the line voltage... -
Page 3: Basic Information
If, despite this, problems are encountered, then please contact us; we would be pleased to help you. Intended use The tool may only used to charge matching Bossard SmartTool batteries as specified in this manual. NOTICE Intended use includes the following: •... -
Page 4: Warranty And Liability
Warranty and liability Warranty and liability claims for personal and property damage are excluded if they occur as the result of one or more of the following: • Unintended usage of the ossard SmartTool charger • Improper installation, placement into service, operation and maintenance of the device •... -
Page 5: Copyright
It contains the relevant rules and information, which may not be • duplicated • distributed or • otherwise shared, either in whole or in part The copyright for these operating instructions remains with HS-Technik GmbH / Bossard AG. Address of the manufacturer: Address of the distributor: HS-Technik GmbH Bossard AG... -
Page 6: Basic Safety Information
2 Basic safety information Information contained in this document A basic prerequisite for safety-compliant handling and problem-free operation is knowledge of the basic safety information and safety regulations. Also be sure to observe all local rules and regulations. Owner responsibilities The owner is obligated to only allow persons who are familiar with basic work safety and accident prevention rules and who have been briefed on proper workplace handling to work at this workplace. -
Page 7: Electrical Hazards
WARNING The workplace is only to be used • for intended purposes • if it is in proper and safe working condition. Electrical hazards DANGER Only allow work to be carried out by electrical specialist. Regularly check the electrical equipment. Rectify loose connections immediately. 2.3.1 Basic safety measures (must always be observed!) a) Keep your work area in good condition. - Page 8 h) Inspect your device for damage. Before using the charger station, the protective equipment or damaged parts must be tested to ensure problem-free functionality according to their intended purpose. Check whether moving parts function properly and determine whether or not they jam, whether any parts are broken, whether all other parts are flawless, are correctly installed and whether all factors that could influence operation of the device are OK.
-
Page 9: Observing The Line Voltage
2.3.2 Observing the line voltage DANGER Adhere to the correct line voltage. Using a higher voltage than is specified can lead to serious injuries of the operator and cause damage to the device itself. In case of doubt, do not connect the device and first verify the line voltage. Structural modifications No changes, extensions or modifications may be carried out on the device without the approval of the manufacturer. -
Page 10: Start-Up And Use
3 Start-up and use NOTICE Only use the charger station in dry rooms. All ventilation slits must be unobstructed. Place the device as far away as possible from exposure to heat and solar energy, as an ambient temperature of more than 35° C can lead to substantially longer charging times. -
Page 11: Technical Data
Charging time 25 - 80 min Switch-off criteria ∆U, temperature termination Dimensions Description BST-BC-2830 and BST-BC-2830-USA Size (W × H × D) 85.5 × 106.8 × 152.5 mm Weight ca. 0.5 kg Additional characteristics • Quick charger for 18 V Li-Ion battery pack •... -
Page 12: Ce Declaration Of Conformity
If the product or its accessories are modified without our consent, this declaration be- comes invalid. Tool description: Quick charger for charging HS-Technik 18 V Li-Ion batteries Type designation: HST-PR-2830 & HST-PR-2830USA BST-BC-2830 & BST-BC-2830-USA Manufacturer: HS-Technik GmbH Im Martelacker 12 D-79588 Efringen-Kirchen Directives:... - Page 13 Notes - 13 -...
- Page 14 Notes - 14 -...
- Page 15 Notes - 15 -...
- Page 16 www.bossard.com...
Need help?
Do you have a question about the BST-BC-2830 and is the answer not in the manual?
Questions and answers