Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zehntner ZGM1130
Summary of Contents for Zehntner ZGM1130
- Page 1 ZGM1130 Glossmeter Technical Manual...
- Page 2 Proceq SA Ringstrasse 2 CH-8603 Schwerzenbach Switzerland Classification: Technical Manual Revision History Date Author, Comments May 17, 2021 PEGG - Initial document copied from ZGM1130 v1.8_en May 18. 2021 PEGG, Initial release 18. May 2021 © Copyright 2021, PROCEQ SA...
-
Page 3: Table Of Contents
Content Safety notes ......................1 Symbols used ......................1 Safety notes and hints....................1 Introduction ......................2 Scope of this document .................... 2 Scope of Delivery ....................3 Standard delivery ..................... 3 Software ........................3 Device overview...................... 5 Display ........................6 Measuring Button ..................... - Page 4 Legal Notices This document can be changed at every time and without any prenotification or announcement. The content of this document is intellectual property of Proceq SA and prohibited to be copied neither in a photomechanical or electronic way, nor in excerpts, saved and/or be passed on to other persons and institutions.
-
Page 5: Safety Notes
All maintenance and repair work which is not explicitly permitted and described in the present instruction manual shall only be carried out by Proceq SA or your authorized Zehntner agent, failure to comply voids warranty. Always disconnect the glossmeter from the USB port of the computer before the permitted maintenance. -
Page 6: Introduction
2.1 Scope of this document This document is an instruction manual for the ZGM1130 Glossmeter family, which describes the correct use of the instrument. This manual covers all models of the ZGM 1130 series which includes 1-, 2- or also 3-angle models. Therefore, it is possible that some pictures or functional descriptions (e.g. -
Page 7: Scope Of Delivery
3 Scope of Delivery 3.1 Standard delivery The following parts are included in the delivery: ZGM 1130 Content ZGM 1130 glossmeter calibration standard microfiber cleaning cloth Wrist loop certificate of manufacturer certificate of calibration carrying case 3.2 Software A software for windows PCs is available to connect to the device. This software allows to read data from the device. - Page 8 Part of this package are also two APIs, which allow automized measurement: Labview programming interface „GlossTools“ programming interface (.NET API) Proceq refuses all warranty and liability claims for damages caused by usage of the ZGM 1130 in combination with non-original accessories, or accessories from 3 party suppliers.
-
Page 9: Device Overview
4 Device Overview Touch Display USB Interface Calibration standard Measuring button Measuring opening 18. May 2021 © Copyright 2021, PROCEQ SA... -
Page 10: Display
If the device is charging, will be displayed in the upper right corner of the display. Only a Zehntner Service Center is allowed to replace the battery. 4.4 Automatic System Check The ZGM 1130 provides an automatic system check functionality. The device is turned on when placed on the calibration standard a system check will be performed during the startup phase. -
Page 11: Download
A battery charging symbol will be displayed in the upper right corner of the display when charging. The ZGM 1130 can be charged either via a USB PC connection or with a USB wall charger. The latter will charge the ZGM 1130 faster than the USB PC connection. 4.5.2 Download This mode connects the ZGM 1130 as a flash drive to the PC, and enables the user to download measuring files directly from the device to the PC without installing any other... -
Page 12: Menu Structure
4.8 Menu Structure The table below shows the menu structure of the ZGM 1130. New File Archive Open File View Data 20° 60° 85° Calibrate Calibrate Calib. value Setup Basic Simple Orientation Right Hand View Pass / Fail Upper Limit Pass / Fail 20°... -
Page 13: Archive
4.8.1 Archive Every measurement is stored in a measurement file. These measurement files can be created, reopened, viewed or deleted in the archive menu. All measurement files are also accessible through USB. New File Creates a new measurement file with an individual name. The filename must not be longer than 8 characters. -
Page 14: Calibrate
4.8.2 Calibrate It is necessary to calibrate the device from time to time. This is may be required particularly if ambient conditions have been changed since the last calibration. It is recommended to calibrate the device at least every 2 days. This function will automatically calibrate all available geometries against a calibration standard. - Page 15 Off - Switches the ZGM 1130 off. View The view of the display can be set-up to either a Simple View which improves readability of the measuring display, but shows less detailed statistic information or to a Detailed View which shows more detailed statistic information but in a smaller font. Simple View Detailed View x̄...
- Page 16 Pass / Fail Switches the Pass / Fail functionality for all supported angles on or off. 20 ° 60 ° 85° & H Lower and higher limits can be defined for each supported angle individually. If the measured value is below or above of these values the measured value will be marked with a Angles...
-
Page 17: Modes
Units The measured values (except Haze) can be displayed either in Gloss Unit (GU) or as a percentage relative to the selected measuring angle. 100% @ 20° ≡ 2037 GU 100% @ 60° ≡ 1000 GU 100% @ 85° ≡ 161 GU Date / Time Set up date, local time and the time in minutes after the device will turn off when not used. -
Page 18: Reset
4.8.5 Reset To reset the device press the reset button through the hole at the bottom of the device with a paper clip or something similar. 18. May 2021 © Copyright 2021, PROCEQ SA... -
Page 19: Operation And Handling Zgm 1120
5 Operation and handling ZGM 1120 The following paragraph guides through how gloss should be measured with a ZGM 1130. Beside this the following notes shall be considered: Proper measurements are only possible on even, clean and unscratched surfaces. Always indicate the used measuring geometry for all measurements. Measurements of different geometries can neither be compared nor converted into another. -
Page 20: Using The Zgm 1130 With "Glosstools
5.2.2 Using the ZGM 1130 with “GlossTools” In order to use the ZGM 1130 connect the device via USB to a PC. When the device is connected chose “Measure” from the pop-up menu on the device to establish a connection with “GlossTools”. While connected measurements can be triggered with the measurement button of the device or by software. -
Page 21: Measurement File
6 Measurement File All measurement files are stored in the internal memory and can be downloaded via USB. When the ZGM 1130 is connected to USB choose Download and the device will appear as a flash drive on the Computer. Measurement files are comma separated (CSV) and can be viewed with any notepad or spreadsheet program. -
Page 22: How To Choose The Correct Measuring Geometry In The Area Of Paint Industry
7 How to choose the correct measuring geometry in the area of paint industry The following explanations apply to smooth coated surfaces, they do not fully apply for metallic and textured coatings or uneven surfaces. They do not apply at all for other surfaces such as foils, metals, textiles and paper. -
Page 23: Maintenance And Cleaning
Cleaning of the standard (see section 8.3) All other maintenance and repair operations may only be done by Zehntner or your authorized Zehntner-agent, otherwise all warranty will be void. 8.2 Cleaning of the aluminum housing Before cleaning disconnect the USB-cable from your computer. For cleaning of the aluminum housing use a proper, soft and moist cloth. -
Page 24: Technical Specification
9 Technical Specification Geometry ZGM1130.6 1-angle: 60° ZGM1130.26 2-angle: 20°, 60° and reflection haze H ZGM1130.268 3-angle: 20°, 60°, 85° and reflection haze H Surfaces All kind of materials such as e.g. paint, coatings, plastic and metals 20° High gloss 60°... - Page 25 For safety and liability information, please download at www.proceq.com/downloads Subject to change. Copyright © 2021 by Proceq SA, Schwerzenbach. All rights reserved. 18. May 2021 © Copyright 2021, PROCEQ SA...
- Page 26 ROCEQ ROCEQ UROPE Ul. Optikov 4 Ringstrasse 2 korp. 2, lit. A, Office 410 CH-8603 Schwerzenbach 197374 St. Petersburg Switzerland Russia +41 43 355 38 00 +7 812 448 35 00 info-europe@proceq.com info-russia@proceq.com UK L ROCEQ Bedford i-lab, Priory Business Park ROCEQ IDDLE Stannard Way...