Download Print this page
Rowlinson Gainsborough Gazebo Assembly Instructions

Rowlinson Gainsborough Gazebo Assembly Instructions

Advertisement

Quick Links

Before assembly
We recommend that time is taken to read the
instructions before starting assembly, then
follow the easy step by step guide.
The instruction sheet is only a guide to
the assembly. Certain items may not be
shown to scale.
Check all components prior to assembly
This product should be assembled by no
less than 2 people.
Never attempt to erect the assembly in
high winds.
Drill components where indicated.
x 2
Drill
Recommended tools for assembly
Cross head screw driver
Drill with 4mm diameter drill bit
Spirit level
Step ladder
Gazebo foot print dimensions
1280mm
2560mm
No.
Components
1
Square base plate
2
Rectangle base plate
3
Floor bearer (flat end)
4
Floor bearer (angled end)
5
Floor bearer (pointed end)
6
Floor bearer separators
7
Floor panels
8
Floor/inner roof centre piece
9
Upright post
10
Top frame
11
Top frame corner supports
12
Centre roof block
13
Roof rafters
14
Roof panels
15
Roof triangles
16
Left roof coverstrips
17
Right roof coverstrips
18
Floor edges
19
Full solid infill panel
20
Solid half infill panels
21
Lattice infill panels
22
Hand rails
23
Left corner finial
24
Right corner finial
No.
Fixing Kit
25
Metal L-brackets
26
70mm screws
27
60mm screws
28
40mm screws
Gainsborough Gazebo
Assembly Instructions
Qty.
1
6
2
2
2
6
6
2
6
6
6
1
6
6
6
6
6
6
1
2
4
5
1
1
Qty.
12
18
106
130
16
13
22
23
24
1
2
3
English SS171
12
15
14
11
9
21
8
7
20
6
17
10
19
18
5
4

Advertisement

loading
Need help?

Need help?

Do you have a question about the Gainsborough Gazebo and is the answer not in the manual?

Questions and answers

Summary of Contents for Rowlinson Gainsborough Gazebo

  • Page 1 Gainsborough Gazebo English SS171 Assembly Instructions Before assembly • We recommend that time is taken to read the instructions before starting assembly, then follow the easy step by step guide. The instruction sheet is only a guide to the assembly. Certain items may not be shown to scale.
  • Page 2 1. Base Prepare a level area for the gazebo to sit. Position the 6 floor bearers as shown in the diagram. Support the bearers at the centre using the square base plate and at the outer end of each bearer using the rectangular base plates. Flat end floor bearer Rectangular base plate Pointed end floor bearer...
  • Page 3 5.Top frames With all the upright posts secured into position. Drill pilot holes at each end of the top frames as shown in the diagram. Secure the top frames to the ends of the uprights using 2 x 70mm screws. Screw through the drilled holes into the ends of the uprights. Drill 2 holes in each corner support as shown below secure one to the inside of each corner of the top frames, secure through the drilled hoes of the support into the top frames using 2 x 60mm screws per support.
  • Page 4 8. Securing the floor and inner roof centre piece Secure each floor panel down using 6 x 60mm screws as shown, fix the centre piece of the floor using 2 x 60mm screw. Inside the roof of the gazebo secure to the bottom of the roof centre block the hexagonal inner roof centre, ensure it is central to the block and fix in place using 2 x 60mm screws.
  • Page 5 Infill panel variations Supplied with the Gainsborough Gazebo are infill panels and hand rails that allow different options depending on the look required. Shown below are 3 possible panel combinations. It is important to note that not all infill panels and hand rails will be used and what is left over will depend on the combination chosen. When fixing the panels and hand rails refer to section 10.