Table of Contents
Advertisement
Quick Links
INDEX
Component list . . . . . .2
Tool list . . . . . . . . . . . .4
1
Unpacking . . . . . . . . . .5
2
Stem & Handlebar . . . . .6
3
Front wheel . . . . . . . . .7
4
Set bike up . . . . . . . . . .9
5
Fender . . . . . . . . . . . . .10
6
Fender stays . . . . . . . .11
7
Seatpost . . . . . . . . . . . .12
8
Saddle . . . . . . . . . . . . .13
9
Angles . . . . . . . . . . . . .14
10 Bell . . . . . . . . . . . . . . . .15
11 Pedals . . . . . . . . . . . . .16
12 Reflector . . . . . . . . . . .17
13 All set up . . . . . . . . . . .18
14 Maintenance . . . . . . . . .19
A new Pelago bicycle is packed pre-assembled in a box with
most of the parts already installed.
The bicycle is packed in the box to prevent it from damage
in shipping, and that's why some parts are not installed. Don't
worry - assembling the bike is easy and soon you'll be riding!
These instructions are only guidelines for building up your new
bicycle and there might be small variations with specific models.
If you have any questions or do not understand something in the
instructions, consult with your local dealer, bicycle shop or our
web support.
This manual is not intended as a comprehensive use, service,
repair or maintenance manual. Please see a dealer or professional
bicycle service for all service, repairs or maintenance.
MANUFACTURER
Pelago Mfg Ltd.
Helsinki, Finland
info@pelagobicycles.com
TEL +358 (0)45 161 6847
Advertisement
Table of Contents
Summary of Contents for Pelago Brooklyn
-
Page 1: Table Of Contents
INDEX A new Pelago bicycle is packed pre-assembled in a box with Component list . . . . . .2 most of the parts already installed. Tool list . . . . . . . . . . . .4 Unpacking . -
Page 2: Component List
COMPONENT LIST Head tube Saddle Top tube Seat post Down tube Seat post clamp Seat tube Front hub Chain stay Rear hub Seat stay Spokes Bell Gear cable Fork crown Fork blade Tire Dropouts Inner tube valve Headset Chain Stem Front chainring Handlebar Crank arm... -
Page 3: Tool List
TOOL LIST NOTE Be careful not to scratch paintwork or damage UNPACKING bicycle while unpacking. PHILLIPS PEDAL 15 MM 10 MM SCREWDRIVER WRENCH WRENCH WRENCH SET UP BICYCLE ON THE BACKWHEEL AND FORK 4 MM 5 MM 6 MM ALLEN KEY ALLEN KEY ALLEN KEY SCISSORS... - Page 4 NOTE You don’t need to adjust INSERT STEM WITH CAPRI AND SAN SEBASTIAN MODELS the handlebar angle just yet! TO FRAME INSERT HANDLEBAR TO STEM 20 Nm 6 Nm REQUIRED TOOLS REQUIRED TOOLS 6 MM ALLEN KEY 4 MM ALLEN KEY...
-
Page 5: Front Wheel
NOTE Install the front wheel INSTALL FRONT WHEEL SET BIKE UP so that the tyre tread rotation WITH KICKSTAND TO FORK direction is correct. NOTE Make sure the axle sits TIGHTEN FRONT WHEEL straight at the bottom of the forks. TO FORK 30–40 Nm REQUIRED TOOLS... -
Page 6: Fender
REMOVE NUT AND WASHER REMOVE FENDER BOLTS AND FROM FRONT BRAKE FENDER STAY CLAMPS NOTE Make sure the front brake INSTALL INSTALL caliper sits straight and the brake FENDER FENDER STAYS pads don’t rub the rim. 6 Nm 8 Nm REQUIRED TOOLS REQUIRED TOOLS 5 MM ALLEN KEY... -
Page 7: Seatpost
INSTALL SEATPOST CLAMP REMOVE AND SEATPOST SADDLE CLAMP MINIMUM INSERTION INSTALL SADDLE 8 Nm 22 Nm REQUIRED TOOLS REQUIRED TOOLS 5 MM ALLEN KEY 6 MM ALLEN KEY... -
Page 8: Bell
CHECK INSTALL SADDLE ANGLE BELL 22 Nm CHECK HANDLEBAR ANGLE ~10° 6 Nm REQUIRED TOOLS PHILLIPS SCREWDRIVER... -
Page 9: Pedals
NOTE Right hand pedal threads NOTE A bike model that is INSTALL RIGHT PEDAL INSTALL tightens CLOCKWISE . equipped with dynamo lights, the (DRIVE SIDE) FRONT REFLECTOR reflector is integrated in to the lights. NOTE Check the marking: R TIGHTEN CLOCKWISE 35 Nm NOTE Left hand pedal threads... - Page 10 YOUR BIKE IS BUILT UP! CONGRATULATIONS! Your new Pelago bicycle is now assembled, but All the new components on the bicycle have a before riding remember to check the following break-in period in which bolts get a bit looser, important parts of your bicycle. It is important that...