Advertisement
Available languages
Available languages
DIGITAL BATH AND AMBIENT TEMPERATURE
Dear Customer,
Thank you for purchasing this product. We hope you will find
it satisfactory. Please read these instructions carefully to take
full advantage of your product.
The Petit Terraillon thermometer is equipped with multiple
functions. It measures the temperature of the water and the room
temperature. It displays the time in room temperature mode and
offers a countdown function to monitor the time baby spends
in the bath.
READ BEFORE USE
• The temperature of the bathwater can vary from one point to
another. You should mix the water thoroughly to make sure the
temperature is the same throughout the bath.
• Never leave baby unattended in the bath.
• Always clean the thermometer with a non-abrasive detergent.
Temperatures not to exceed:
For the bath:
• Between 36°C and 38°C: ideal temperature, comfort is ensured.
• Over 39°C: water is too hot, risk of burns.
In the bathroom:
• Around 22°C: ideal temperature recommended.
In the bedroom:
• Around 18°C: ideal temperature recommended.
6
PRODUCT DESCRIPTION
1- Clock / countdown / SCAN 7- Wave symbol = water mode
2- Temperature
8- Temperature units of
measurement (Degrees
Celsius / Degrees Fahrenheit)
3- SCAN button
9- Alarm symbol
4- LED - Visual alarm
10- Battery compartment
5- Clock symbol
11- SET button
6- Battery empty
USING THE PRODUCT
ADJUSTMENTS
• To make any adjustments, open the battery compartment by
unscrewing to the left.
• Close the battery compartment again once you have made any
adjustments.
Battery
• A CR2032 lithium battery is supplied.
• You must insert it into the battery compartment to enable the
thermometer to operate.
Clock
• Format: HH:MM (24-hour clock)
• Press the SET button for around 5 seconds. The time will start to
flash.
• Set the time with the SCAN button and validate with the SET
button.
• Next, the minutes start to flash. You can adjust this in the same
way as for the hour previously.
• If no button is pressed within 10 seconds, the device will return
to Room mode and will not take any of the adjustments made
into account.
• The clock is only displayed in Room mode. When the device is
immersed in water, the clock is deactivated.
Temperature adjustment
• The default setting for the unit is degrees Celsius (°C). Degrees
Fahrenheit (°F) is also available.
• To switch from one unit of measurement to the other, press the
SET button for 1 second. The unit of measurement starts to
flash.
• Press the SCAN button to switch and then press the SET button
to confirm your selection.
OPERATION
Water temperature
• Immersed in the bath, the thermometer floats, with the display
on the surface, so you can read the information more easily.
• The thermometer automatically detects that it is in water: the
wave symbol appears.
• The alarm symbol and the red LED flash at the same time when
the water temperature is lower than 36°C or over than 38°C.
Two methods can be used to measure the water
temperature:
• "FLOAT" mode: the thermometer automatically measures and
displays the water temperature every 5 seconds as long as it
stays in contact with the water.
• "SCAN" mode: the thermometer measures and displays the
water temperature every second for 10 seconds. This mode is
recommended to check that the water is mixed well, to ensure
the temperature is the same everywhere.
• To use it, press the SCAN button for 1 second. The word "SCAN"
starts to flash at the top of the display for 10 seconds.
The temperature is measured and displayed every second.
• After the 10 seconds, the thermometer switches back into
"FLOAT" mode automatically.
From water temperature to room temperature
When the thermometer is taken out of the water, it automatically
switches to "Room Mode". The Water symbol and the
last temperature measurement flash at the same time for
10 seconds.
Room temperature
• The thermometer automatically measures and displays the tem-
perature of the bathroom and baby's bedroom.
• The room temperature is updated every 20 minutes.
• The alarm symbol flashes on the display when the room tempe-
rature is lower than 15°C or higher than 25°C.
• "SCAN" mode can be used to measure the room temperature
every second for 10 seconds. Refer to the instructions above at
"SCAN" mode.
• After 10 seconds in "SCAN", the thermometer automatically
switches back to room mode.
Countdown
• This function can be used in the water or in room mode.
• The countdown is 10 minutes, which is the optimum duration for
baby's bath.
• To activate it, hold down the SCAN button for about 3 seconds,
until the 10 minutes and clock symbol appear at the top of the
display.
• Once the 10 minutes is up, the green LED, figures and
clock symbol all flash at the same time for 15 seconds.
• To stop the countdown, hold the SCAN button down for about 3
seconds.
LED / VISUAL ALARM: COLOUR LEGEND
LED colour
Meaning
Red
The water temperature is too high
(>38°C) or too low (<36°C).
Green
The 10 minute countdown time is up.
Green then red
in the water, the countdown has just
alternately
when the red LED starts to flash;
ended
and vice versa.
Orange
The countdown has ended along with a
notification that the water temperature
is too high or too low.
7
Advertisement
