Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Fly Wing H1-Heli
Summary of Contents for Fly Wing H1-Heli
- Page 1 Heli User Manual V2.6 Manual 2021.03...
- Page 2 1. Check whether the main blades ,tail blades, helicopter body and landing skids are damaged or distorted, please replace them with the genuine Fly Wing RC parts. 2. Check whether the flight control linkages and fuselage are fixed firmly, and whether the GPS unit is correctly fixed on the helicopter tail boom (horizontally placed, straight line behind the main mast ) H1 Unit is fixed firmly on the double sided foam pad either at the front or at the back of the main mast.
- Page 3 H1 user manual 10.to control the helicopter manually by turning the transmitter 3D mode switch in case of Emergency . 11.Please note that the helicopter is still in the Auto GPS flight mode state at this time. If you need to completely exit the flight mode, please turn the flight stop button on the transmitter.
- Page 4 H1 user manual The documentation of this product is subject to update without prior notice. Please visit the official website http://www.flywingrc.com , go to the product page for the latest information. About H1 Overview The H1 helicopter flight control system, with its built-in floating IMU and double-layer damping sponge, combined with a new generation of control and IMU algorithms, makes it easy to experience helicopters.
- Page 5 H1 user manual About main controller port： Pin Port ： Receiver,servo,ESC connection 2. USB Port： TYPE-C port ， connect to computer to adjust 3. GPS Port ： Interface between external compass 4. LED： H1 status indicator Support swash plate Type：： Right servo Left servo Forward servo...
- Page 6 H1 user manual Installation Overview Install procedure Please read this section carefully, install and set up your flight control system according to the following process to ensure the normal operation of the system. 1. Ensure that the modules required for installation are complete. 2.
- Page 7 Support Win7, Win8 , Win10（32 or 64 bit） Use TYPE-C USB wire connect flight controller and your computer Drive H1-Heli installation package and install it according to the prompts. Double-click H1-Heli icon to run the parameter adjustment software. For safety, when adjusting the parameters, please remove the blade or disconnect the motor The original Win10 64 bit operating system is recommended to achieve the best experience.
- Page 8 H1 user manual Start Installation It is necessary to install and set parameters properly according to the requirements, otherwise, it may not be able to fly or even cause serious safety accidents. Installation Steps :1、Install main controller and GPS；2、Connection；3、Set transmitter；4、Adjust software ...
- Page 9 H1 user manual Face up, never upside down If you need to use in severe cold conditions，Please do a good job of heat preservation. It is recommended to install it close to the place with small vibration It is recommended to install it close to the position with small vibration and parallel to the fuselage. The vibration near the center of gravity is small The flight control system is not waterproof, oil proof and dust-proof.
- Page 10 H1 user manual Aircraft equipment connection: When using H1, it is necessary to connect the receiver, ESC, battery and other related equipment, and set their parameters in the software, otherwise it may not be able to fly or even lead to serious safety accidents.A helicopter with a tail servo,don't connect the servo.
- Page 11 H1 user manual Transmitter settings Transmitter Requirement: The transmitter must support SBUS mode.It has at least 9 channels and own Failed-Safe function.And you can set the out of control protection output of all channels by yourself.Otherwise, the out of control protection function cannot be realized.
- Page 12 H1 user manual Adjust software Install new helicopter： Please watch the “ tutorial video”， run parameter adjustment assistant ， Complete the parameter setting according to the software guidelines.The specific process is as follows: 1. Ensure the power supply of flight control system is normal. 2.
- Page 13 H1 user manual 8.After importing parameters successfully,calibrate transmitter according to the prompts on the left ； If the software display is inconsistent with the direction of the transmitter （ The transmitter is pushed forward , and the software progress bar is at the "back" end），The corresponding channel is reversed in the menu of the transmitter（Refer to the remote control manual for details），until all channels are correct.
- Page 14 H1 user manual If it is not the helicopter with this configuration, please select the Universal model top for installation; select the helicopter with the corresponding size (here, the length of a single rotor is used to distinguish the helicopter type.) Click”swash “...
- Page 15 H1 user manual .Click “Tail”，follow the prompt to select the servo type first, then click the slider to the left, if the slider is to the right, click the tail servo output to reverse; then click the tail servo back, calibrate the neutral point, The far left of the slider and the far right of the slider, drag the slider until the slider just touches the maximum limit of the tail axis.
- Page 16 H1 user manual The error message can be displayed below the main interface connection，When the aircraft is abnormal, it can not be powered off，Connect the computer to view the error message and correct it（See the common errors and solutions section for solutions). After installing the new helicopter, the tail gain and throttle value can be set in the main interface 2.Main rotor adjustment After installing the new helicopter，the transmitter mode is in 3D.
- Page 17 H1 user manual Parameters Adjust the sensitivity according to the helicopter state.The default standard flight is recommended to meet the needs of most helicopter.Clear the default value of aircraft parameters and click the button to clear all flight control data and restore the default settings(you don't need to click on it except in special circumstances). If the tail swings quickly from left to right, the tail gain can be reduced.
- Page 18 H1 user manual Calibration procedure： Please select an open space and calibrate the compass according to the following steps. If you want to see more about compass calibration, please watch the relevant teaching video. Method：Calibration with parameter adjustment software： Enter the sensor page of parameter adjustment software and click to start compass calibration. The rotor rotates 360 °...
- Page 19 H1 user manual Function Flight Function Flight Mode: Flywing designs a variety of control modes for users ， Using different control modes, the flight performance of the aircraft will be different，You can set the transmitter 5-channel switch as the flight mode switch through the parameter adjustment software.
- Page 20 H1 user manual Home Mode The process that the helicopter automatically returns to the last recorded return point is called return. There are three different ways to return: Out of control return： When the GPS signal is good, the Compass works normally, and the return point is successfully recorded (the point of each helicopter unlocking)，If the transmitter signal is interrupted for more than 3 seconds, the flight control system will control the helicopter to fly back to the nearest recorded return point at an altitude of 15 meters.If the radio signal returns to normal during the return flight, the return flight will continue, but...
- Page 21 H1 user manual *One-key acrobatic Flywing has designed one key switch Normal /Invert mode for users. In inverted mode, GPS can still fly at fixed point and fixed altitude, providing users with a good acrobatic training platform. When using this function, the aircraft will switch between forward flight ...
- Page 22 H1 user manual Flight controller status indicator description ——— Green solid GPS status is good, can take off GPS status has been locked, start switch can • • • Green flash start motor • • • Yellow flash Helicopter is getting positioning Red flash slowly •...
- Page 23 H1 user manual 5 、 While the green light is flashing, dial the 6 、 When the helicopter rotor head speed is CH7,turn the stop switch to run position , and stable, push the throttle stick upwards to take the helicopter motor will run. The blades will off and raise the helicopter above ground , spin quickly.
- Page 24 H1 user manual FAQs Why is the flight control red light flashing and the software prompt compass abnormal after connecting the line and inserting the computer for adjusting? A ： Because the compass is not calibrated or the calibration is unsuccessful, the flight control red light flashes slowly.
- Page 25 Parameter H1 user manual Helicopter type HR3 Flybarless Swashplate H3 Flybarless Swashplate Battery type 3S，4S ，6S Lipo battery,12S do not support low voltage return S.bus / i.bus /w.bus Receiver type SUMD HD 08 Win7，Win8，Win10（32 或 64 bits） Assistant operating system requirements Rated system power Rated peak power...