Page 1
Before applying power to this product, make sure it has been correctly grounded according to the installation instructions. You must read all installation instructions before beginning the installation. If you experience difficulty during the installation, contact Garmin ® Product Support.
Connector Identification Connector Identification (Vieo RV 51) Item Label Description Connector Details Line out connectors for Left (white), right (red), and subwoofer (orange) ZONE 1 LINE OUT zone 1 RCA connectors Line out connectors for Left (white), right (red), and subwoofer (orange)
Page 3
Connector Identification (Vieo RV 52) Item Label Description Connector Details Line out connectors for Left (white), right (red), and subwoofer (orange) ZONE 1 LINE OUT zone 1 RCA connectors Line out connectors for Left (white), right (red), and subwoofer (orange) ZONE 2 LINE OUT zone 2 RCA connectors...
Wiring Harnesses Power and Speaker Wiring Harness The power and speaker wiring harness contains the main power and speaker connections for the system. The harness connects directly to the stereo and to the vehicle wiring harness without modification. You can use this diagram to troubleshoot or to address non-default installation requirements.
Page 5
Left (white), right (red), and sub ZONE 4 Outputs analog audio to an external amplifier for zone 4. (orange) Not used. These connectors are not active for the Vieo RV 51/52 AUX IN 2 product model. You must use the CAMERA AUDIO INPUT Not used...
Page 6
Analog Signal Wiring Harness Wire color Pin Function Notes Connects to the steering wheel controls. Not available for all vehicles. Green Analog input 1 Contact the RV manufacturer for more information. Connects to the steering wheel controls. Not available for all vehicles. Purple Analog input 2 Contact the RV manufacturer for more information.
Page 7
Connecting Vehicle and Backup Cameras You can connect up to four analog vehicle cameras to the infotainment system for backup, left, right, and front cameras. 1 For each camera, route the camera's RCA analog video cable to the back of the stereo. You should clearly label each cable for reference when you are connecting them to the stereo.
Attaching the Display Adapter to the Dock (7-inch Models Only) You should attach the adapter to the dock before you install the dock in a dashboard. 1 Place the adapter on the front of the dock, aligning the four screw holes on the adapter with the dock. 2 Using the included screws , secure the adapter to the dock.
Page 9
Installing the Bracket on the Dock for Freightliner M2 Vehicles 1 Place each bracket on the dock, aligning the holes on the bracket with the holes on the dock. 2 Using the included screws , secure each bracket to the dock. The recommended torque you should apply to the screws is 5.0 to 6.0 lbf-in.
Page 10
Installing the Bracket for FIAT Ducato Vehicles ™ 1 Place the upper bracket on the dock , aligning the holes in the bracket with the holes on the top of the dock. 2 Using the included screws , secure the bracket to the top of the dock. The recommended torque you should apply to the screws is 5.0 to 6.0 lbf-in.
Page 11
Installing the Device in the Left Center Panel You can use the included hardware to flush mount the device in the left center panel opening on a Freightliner Cascadia vehicle. 1 Remove the dashboard front panel. 2 Secure the mount plate to the dashboard using the four screws from the vehicle compartment.
Page 12
10 Install the decorative bezel by snapping it in place around the edges of the device.
Page 13
NOTICE Avoid wires, gauges, air bags, air bag covers, HVAC, and other items when cutting the dashboard and attaching the mount to the vehicle. Garmin is not responsible for any damages or consequences arising from the installation. 1 Place each bracket on the dock , aligning the holes in the bracket with the holes on the dock.
Page 14
Installing the Device in a Dodge ProMaster 1 Place the upper bracket on the dock , aligning the holes in the bracket with the holes on the top of the dock. 2 Using the included screws , secure the bracket to the top of the dock. The recommended torque you should apply to the screws is 5.0 to 6.0 lbf-in.
Page 15
Installing the Device on a Wall The included template and hardware can be used to flush mount the device on the wall in your recreational vehicle. WARNING Always be sure of your mounting location before cutting into a wall. Recreational vehicle walls may contain utility lines.
® , the Garmin logo, Fusion ® , and the Fusion logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Vieo is a trademark ™ of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
Page 17
Apple Inc., registered in the U.S. and other countries. Bluetooth ® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license. Dodge is a registered trademark of FCA US LLC. Freightliner ®...
Need help?
Do you have a question about the Vieo RV 51 and is the answer not in the manual?
Questions and answers