Download Print this page

Vision ZA1502IN-7 Installation & Operation Manual

2 in 1 universal remote

Advertisement

Quick Links

Federal Communications Commission Statement
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution
"the user that changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment."
FCC Statement in User's Manual (for calss B) FCC Section 15.105 "Federal
Communications Commission (FCC) Statement"
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
Vision Guarantees that every wireless ZA1502-7 is free from physical defects in material
and workmanship under normal use for one year from the date of purchase. If the product
proves defective during this one-year warranty period, Vision will replace it free of charge.
Vision does not issue any refunds. This warranty is extended to the original end user
purchase only and is not transferable. This warranty does not apply to: (1) damage to
units caused by accident, dropping or abuse in handling, or any negligent use; (2) units
which have been subject to unauthorized repair, taken apart, or otherwise modified; (3)
units not used in accordance with instruction; (4) damages exceeding the cost of the
product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on addtional devices, please visit us at www.visionsecurity.com.tw
ZA1502-7 V0
1090302
Installation & Operation Manual
ZA1502IN-7
ZA1502EU-7
ZA1502RU-7
ZA1502US-7
ZA1502IL-7
ZA1502KR-7
ZA1502HK-7
ZA1502JP-7
ZA1502BR-7
2 in 1 Universal Remote

Advertisement

loading

Summary of Contents for Vision ZA1502IN-7

  • Page 1 Vision will replace it free of charge. 2 in 1 Universal Remote Vision does not issue any refunds. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to: (1) damage to units caused by accident, dropping or abuse in handling, or any negligent use;...
  • Page 2 Introduction Z-Wave Command Classes: Thanks for choosing the Vision’s wireless 2 in 1 Universal Remote (ZA1502-7) of the home COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3 security device. This sensor is a Z-Wave™ Plus. enabled device (interoperable, two-way RF COMMAND_CLASS_ASSOCIATION_V2 mesh networking technology) and is fully compatible with any Z-Wave™ enabled network and its COMMAND_CLASS_BATTERY security framework.
  • Page 3 Operation Notification V8 Type Notice: If you are installing the entire Z-Wave™ system for the first time, please EVENT refer to the installation guide of Z-Wave™ Interface Controller and full charging the TYPE ZA1502-7 before using.. Movement System (0x09) Heartbeat (0x05) Synchronic Green LED turns on while pressing the button of ZA1502-7...
  • Page 4 8. Battery Capacity Detection: Use “Battery Get” command to have the battery capacity back in %. It will detect the battery capacity automatically. Low Battery Auto Report (low battery is set as 2.4+/-0.1 Voltage). 9. Association: * Support one group with 1 node. * Group 1 = Lifeline (Battery, Notification, Reset Locally) 10.

This manual is also suitable for:

Za1502eu-7za1502ru-7za1502us-7za1502il-7za1502kr-7za1502hk-7za ... Show all