Related Manuals for Leedarson Motion Sensor Pet Immunity Z-Wave 700
Summary of Contents for Leedarson Motion Sensor Pet Immunity Z-Wave 700
- Page 1 We build your success in IoT. LEEDARSON Motion sensor Pet Immunity Z-Wave™ 7CA-SS-VE-C0...
-
Page 2: Product Introduction
Motion Sensor Pet immunity Quick Start Guide 1. Product Introduction The Motion Sensor lets you know when movement is detected in a certain area and can trigger different actions in response to that movement (or lack of movement). It supports the pet immunity up to 80 lbs. - Page 3 Bracket Reset button Button: Short press reset button into learning mode, then the sensor can inclusion or exclusion from the Z-Wave network. Hold the key for 5s to reset the sensor, after reset, Sensor will send “Device_Reset_Locally” to the main controller and exclude from the Z-Wave network when the Button is released, this procedure will reset the Sensor to factory default.
- Page 4 Pet immune 80 lbs (36 kgs) 6.23 ft. to 7.55 ft. Mounting height (1.9m to 2.3m) Light sensor 20 lux for day/night(bright/dark) Protocol Z-Wave 908.42MHz (US) Frequency 868.42MHz(EU) Power source Battery-powered Battery type CR123A X 1 Battery life 3 years Anti-Tamper Low power alarm Certifications...
-
Page 5: Product Installation
Top view 2. Do avoid installation near air-conditioner, electric fans, refrigerators, ovens or other places where temperature easy change. 3. In order not to affect the detecting result, there should be no object in front of the produces lens. 4. Building (such as the wall) will shorten the distance of wireless communication. 5. -
Page 6: Product Usage
③ Assembly the main body to the bracket. 6. Product Usage Function of Action Button: 6.1 All functions of each trigger: Function Of Action Trigger Description In the network: Send Battery report and Wake up notification, the LED turn on within 1 second. Power on Not in the network: Only the LED will be slow blink 3 times. - Page 7 In the network: Send Wake up notification, and LED will fast blink when Short press sending data, send over then the LED turn off. button one time Not In the network: NOP. Reset Motion Sensor to factory default. 1. Triggering this action, in 5 seconds LED will be accelerate blink. After 5 seconds, the LED will remain on until the key is released.
- Page 8 6.3 Low voltage alarm to remind changing battery. This product has low voltage detection reminder, when the battery voltage is in low status, the detector will give out low battery signal to controller. 7. Attention 1. If need to clean the sensor, please use a soft cloth with a little alcohol to wipe it after you cut off the power.
- Page 9 Command Class List Non-Included Non-Secure Included S0 Non-Secure Node Info COMMAND_CLASS_ZWAVEPLUS_INFO COMMAND_CLASS_ZWAVEPLUS_INFO COMMAND_CLASS_ASSOCIATION COMMAND_CLASS_TRANSPORT_SERVICE_V2 Frame COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_SECURITY COMMAND_CLASS_TRANSPORT_SERVICE_V2 COMMAND_CLASS_SECURITY_2 COMMAND_CLASS_VERSION COMMAND_CLASS_SUPERVISION COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_BATTERY COMMAND_CLASS_SECURITY COMMAND_CLASS_SECURITY_2 COMMAND_CLASS_NOTIFICATION_V3 COMMAND_CLASS_SENSOR_MULTILEVEL_V5 COMMAND_CLASS_WAKE_UP COMMAND_CLASS_SUPERVISION COMMAND_CLASS_CONFIGURATION_V4 COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5 COMMAND_CLASS_VERSION Security COMMAND_CLASS_POWERLEVEL Command COMMAND_CLASS_ASSOCIATION Supported Report COMMAND_CLASS_ASSOCIATION_GRP_INFO Frame COMMAND_CLASS_MANUFACTURER_SPECIFIC...
- Page 10 Grouping identifier Group Name Profile MS Profile LS Lifeline 0x00 0x01 On/Off control 0x71 0x07 Association Group Command List Group 1 Command List Support Command Class COMMAND_CLASS_NOTIFICATION_V8(0x71) Command NOTIFICATION_REPORT_V8(0x05) Command Class COMMAND_CLASS_BATTERY(0x80) Command BATTERY_REPORT(0x03) Command Class COMMAND_CLASS_DEVICE_RESET_LOCALLY(0x5A) Command DEVICE_RESET_LOCALLY_NOTIFICATION(0x01) Command Class COMMAND_CLASS_SENSOR_MULTILEVEL_V5(0x31) Command SENSOR_MULTILEVEL_REPORT(0x05)
- Page 11 (0x03) TAMPERING_COVERING_REMOVED (0x08) MOTION_DETECTION_UNKNOWN_LOCATION (0x0A) REPLACE_BATTERY_SOON POWER_MANAGEMENT (0x08) (0x0B) REPLACE_BATTERY_NOW (0x00) NO_EVENT (0x00) NO_EVENT LIGHET_ALARM(0x14) (0x01) LIGHETSENSOR_ALARM_DETECTED Configuration Set Command Class Command Format Command Class = COMMAND_CLASS_CONFIGURATION Command = CONFIGURATION_SET Parameter Number Default Reserved Size Configuration Value 1(MSB) Configuration Value 2 ……...
- Page 12 5.4.1 Parameter Number Definitions (8 bit) Name Info Paramet Default Size Format Altering Value Value Value d-on capabilit Number LowBatPrecent LowBatAlarm 0x0A UNSIGNED Will alters (10) (0x0A) (0x32) (0x05) Read- _INTEGER capabilities only UNSIGNED Will alters 0x0C Pironoff PironoffSet Read- _INTEGER capabilities (0X01)
- Page 13 Enable/Disable the PIR 0 = Disable the PIR. 0x0C(12) 1 = Enable the PIR. Setup the wait time of PIR for clear the motion. 0x0D (13) Valid values: 0x05~0x3BC4 When the Motion Sensor is triggered, if this parameter is 0x01 then it will send Basic set command to group 1. 0x0E (14) 0 = Don't send.
Need help?
Do you have a question about the Motion Sensor Pet Immunity Z-Wave 700 and is the answer not in the manual?
Questions and answers