Congratulations on your latest Target purchase. Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
This Chair comes with a one year limited warranty against original manufacture defects. If you experience trouble with your chair, please call the customer service number below. Target Corporation Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Page 4
table of contents introduction hardware parts list assembly 7-13 QUESTIONS? Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number r eady when calling.
ITEM DESCRIPTION QUANTITY left base right base lower hanging bar upper hanging bar back frame seat frame hook plastic mulffer post plastic part connection part...
Page 7
step 01: (Part P)×3 (Part I)×3 (Part K)×2 (Part N)×3 M8*20mm bolt with washer M8 washer M6*15mm bolt with washer M8 nut (Part S)×1 (Part T)×1 (Part U)×1 (Part V)×1 allen wrench post plastic part connection part wrench ATTENTION: To avoid damage to your new patio furniture, please use either the carton or another soft surface such as carpet as a working surface to prevent product damage during assembly.
Page 8
step 02: (Part H)×2 (Part I)×4 (Part N)×6 M8*15mm bolt M8 washer M8*20mm bolt with washer (Part O)×2 (Part U)×1 (Part P)×4 (Part V)×1 allen wrench M8 spring washer wrench M8 nut 1. Attach the lower hanging bar (C) to the left base (A) and right base (B) by lining up the bolt holes on the lower hanging bar (C) with the corresponding bolt holes on the left base (A) and right base (B).
Page 9
step 03: (Part G)×2 (Part N)×2 (Part P)×2 (Part R)×1 M8*55mm bolt M8 nut M8 washer plastic muffler (Part S)×1 (Part U)×1 (Part V)×1 post plastic part allen wrench wrench 1. Connect upper hanging bar (D) and lower hanging bar (C) by using post plastic part (S). Secure with M8*55mm bolt (G), M8 washer (N) and M8 nut (P) using allen wrench (U) and wrench (V).
Page 10
step 04: (Part J)×4 (Part L)×4 (Part M)×4 M6*45mm bolt with washer M6 nut M6 washer (Part R)×1 (Part U)×1 (Part V)×1 allen wrench plastic muffler wrench 1. Attach the back frame (E) to the seat frame (F) by lining up the bolt holes on the back frame (E) with the corresponding bolt holes on the seat frame (F).
Page 11
step 05: (Part Q)×1 hook 1. Follow the diagram in circle 1 to open the hook (Q). Connect the upper hanging bar (D) and back frame (E) by using the hook (Q). Then tighten the hook (Q). Do not completely tighten screws until all screws are in place.
Page 12
step 06: 1. Open the hook of safety rope on the seat frame (F), pass through the bottom of the lower hanging bar (C). Then tighten the hook of safety rope. Do not completely tighten screws until all screws are in place.
Page 13
step 07 1. Tighten all the bolts. 2. Put the cushion on the chair. You are now ready to enjoy your new chair.
Page 15
2020 Target. The Bullseye Design is a trademark of Target Brands Inc. All rights reserved.