Page 1 Please read this User’s Guide thoroughly before you use the printer. Keep the CD-ROM in a convenient place so you can use it quickly if you need to. Please visit us at http://solutions.brother.com/ where you can get product support, the latest driver updates and utilities, and answers to frequently asked questions (FAQs) and technical questions.
Page 2: Symbols And Conventions Used In The Documentation
Symbols and conventions used in the documentation The following symbols and conventions are used throughout the documentation. Bold Bold typeface identifies specific keys on the product’s control panel or on the computer screen. Italics Italicized typeface emphasizes an important point or refers you to a related topic.
Page 3: Table Of Contents
Connecting a camera as a storage device ...24 DPOF printing...25 Printing images with Secure Function Lock 2.0 enabled (HL-3075CW only) ...25 Printing data from a USB flash memory drive with direct print (HL-3075CW only)...27 Supported file formats ...27 Direct Print default settings...27 Creating a PRN or PostScript Printing data directly from the USB flash memory drive ...29...
Page 4 Cancel ...75 Secure Print...75 + or - button ...75 Back...76 OK ...76 LEDs ...76 LCD ...76 Back light (HL-3075CW only) ...77 LCD messages ...77 Reprinting documents...78 Printing Secure data ...79 Using the control panel LCD menu...81 Menu table...82 Default settings...93 Frequency...95...
Page 5 Symbol and character sets (HL-3075CW only) ...172 How to use Web Based Management (web browser) ...172 Symbol and character sets list...173 Quick reference for bar code control commands (HL-3075CW only) ...175 Print bar codes or expanded characters...175 Libtiff Copyright and License ...183 Appendix (for Europe and Other Countries) Brother numbers ...184...
Page 6: Printing Methods
Type and size of paper The printer loads paper from the installed paper tray or the manual feed slot. The names for the paper trays in the printer driver and this guide are as follows: Paper tray Manual feed slot When looking at this page on the CD-ROM, you can jump to the page for each printing method by clicking p in the table.
Page 7: Recommended Paper
IMPORTANT • DO NOT use ink jet paper because it may cause a paper jam or damage your printer. • If you use paper that is not recommended, a paper jam or misfeed may occur in the printer. Note • Preprinted paper must use ink that can withstand the temperature of the printer's fusing process (200 degrees centigrade).
Page 8 You should buy quality envelopes from a supplier who understands that you will be using the envelopes in a laser printer. Before you print a lot of envelopes, test one to make sure that the print results are what you want.
Page 9: Unprintable Area
The area of the paper that cannot be printed on is shown in the table below: Note The area that cannot be printed on may vary depending on the paper size and the printer driver you are using. The unprintable area shown below is for A4 / Letter size paper.
Page 10: Printing Methods
Printing on plain paper from the paper tray (For the recommended paper to use, see About paper on page 1.) Pull the paper tray completely out of the printer. While pressing the green paper-guide release lever, slide the paper guides to fit the paper size. Make sure that the guides are firmly in the slots.
Page 11 Make sure the paper guides touch the sides of the paper so it will feed properly. Put the paper tray firmly back in the printer. Make sure that it is completely inserted into the printer. Lift up the support flap (1) to prevent paper from sliding off the face-down output tray, or remove each page as soon as it comes out of the printer.
Page 12 (See Driver and Software in Chapter 2.) ®  Windows printer driver BR-Script printer driver for Windows  Note To use the BR-Script printer driver for Windows the CD-ROM. ® (HL-3075CW only) ® you must install the driver using the Custom Install from Printing Methods...
Page 13 Printing Methods  Macintosh printer driver Send the print data to the printer.
Page 14 (For the recommended paper to use, see About paper on page 1.) Note The printer automatically turns on the Manual Feed mode when you put paper in the manual feed slot. Lift up the support flap (1) to prevent paper from sliding off the face-down output tray, or remove each page as soon as it comes out of the printer.
Page 15 • Do not put more than one piece of paper in the manual feed slot at any one time, as it may cause a jam. • If you put paper or other print media in the manual feed slot before the printer is in the Ready state, an error may occur and the printer will stop printing.
Page 16 (See Driver and Software in Chapter 2.). ®  Windows printer driver  BR-Script printer driver (HL-3075CW only) Note To use the BR-Script printer driver for Windows the CD-ROM. ® you must install the driver using the Custom Install from...
Page 17  Macintosh printer driver Send the print data to the printer. After the LCD shows Manual Feed, put in the next sheet of paper as in step d and repeat for each page you want to print. Note The LCD will show Manual Feed until a sheet of paper is put in the manual feed slot.
Page 18: Printing On Thick Paper, Labels And Envelopes
When the back output tray is pulled down, the printer has a straight paper path from the manual feed slot through to the back of the printer. Use this paper feed and output method when you want to print on thick paper, labels or envelopes.
Page 19 • Do not put more than one piece of paper or one envelope in the manual feed slot at any one time, as it may cause a jam. • If you put paper or other print media in the manual feed slot before the printer is in the Ready state, an error may occur and the printer will stop printing.
Page 20 Paper Size ... (1) Media Type ... (2) Paper Source ... (3) and any other settings you may want to make. (See Driver and Software in Chapter 2.). ®  Windows printer driver  BR-Script printer driver (HL-3075CW only) Printing Methods...
Page 21 CD-ROM. • When you use Envelope #10, choose Com-10 for the Paper Size. • For other envelopes which are not listed in the printer driver, such as Envelope #9 or Envelope C6, choose User Defined... (for Windows ®...
Page 22 Note • If envelopes get smudged during printing set the Media Type to Thick Paper or Thicker Paper to increase the fixing temperature. • If the envelopes are creased after they are printed, see Improving the print quality on page 153. ®...
Page 23: Duplex Printing
Duplex printing The supplied printer drivers all enable duplex printing. For more information about how to choose the settings, see the Help text in the printer driver. Guidelines for printing on both sides of the paper  If the paper is thin, it may wrinkle.
Page 24: Manual Duplex Printing
Manual Duplex / Booklet setting, and then from the Basic tab choose the Paper Source to be Tray1. Send the data to the printer, then click OK on the computer screen. The printer will automatically print all the even-numbered pages on one side of the paper first.
Page 25 The printer will now automatically print all the odd-numbered pages on the other side of the paper. Note When you put paper in the paper tray, first empty the tray. Next, put the printed pages in the tray, with the printed side face up.
Page 26 Using both hands put the paper in the manual feed slot with the side that is going to be printed on first facing up. Send the data to the printer, then follow the instructions on the computer screen. Repeat this step until you have printed all the even-numbered pages.
Page 27: Booklet Printing (For Windows Printer Driver)
Booklet printing (for Windows Put paper in the paper tray or manual feed slot. Open the Properties dialog box in the printer driver. From the General tab, choose the Printing Preferences button. From the Basic tab, choose Booklet from the Manual Duplex / Booklet setting. If you want to change the booklet printing setting, click Duplex Settings.
Page 28: Printing Photos From A Digital Camera (Hl-3075Cw Only)
Print Quality The default settings are shown in Bold with an asterisk. These menu selections are also set by your camera. Camera settings are prioritized as long as your camera is not set to use the Printer Settings (Default settings).
Page 29: Printing Images
Make sure that your camera is turned off. Connect your camera to the USB direct interface (1) on the front of the printer using a suitable USB cable. Turn on the camera. When the printer has recognized the camera, the LCD shows the following message Camera Connected Set your camera to print an image.
Page 30: Dpof Printing
 Copies  Printing images with Secure Function Lock 2.0 enabled (HL-3075CW only) For more information about Secure Function Lock 2.0, see Chapter 14 of the Network User’s Guide on the CD-ROM we have supplied. Make sure that your camera is turned off. Connect your camera to the USB direct interface (1) on the front of the printer using a suitable USB cable.
Page 31 If your ID has the restricted options, the following messages appear on the LCD. Message Meaning Printing pictures directly from a camera to the Brother machine is restricted. Access Denied The number of pages you are allowed to print is exceeded. The print job will be Limit Exceeded canceled.
Page 32: Printing Data From A Usb Flash Memory Drive With Direct Print (Hl-3075Cw Only)
With the Direct Print feature, you do not need a computer to print data. You can print by just plugging your USB flash memory drive into the printer´s USB direct interface. There might be some USB flash memory drives that will not work with the printer. Supported file formats Direct print supports the following file formats: ...
Page 33: Creating A Prn Or Postscript 3™ (Hl-3075Cw Only) File For Direct Printing
From the menu bar of an application, click File, then Print. Choose HL-3075CW (1) and check the Print to file box (2). Click Print. Choose the folder you want to save the file to and enter the file name if you are prompted to. If you are prompted for a file name only, you can also specify the folder you want to save the file in by entering the directory name.
Page 34: Printing Data Directly From The Usb Flash Memory Drive
Printing data directly from the USB flash memory drive Connect your USB flash memory drive to the USB Direct Interface (1) on the front of the printer. When the printer has recognized the USB flash memory drive, the LCD shows the following message.
Page 35: Printing Data Directly From The Usb Flash Memory Drive With Secure Function Lock 2.0 Enabled (Hl-3075Cw Only)
For more information about Secure Function Lock 2.0, see Chapter 14 of the Network User’s Guide on the CD-ROM we have supplied. Connect your USB flash memory drive to the USB Direct Interface (1) on the front of the printer. When the printer has recognized the USB flash memory drive, the LCD shows the following message.
Page 36 Go, then press + or - to enter the number of copies you want, then press Go. Printing Default settings Paper Size Media Type Output Color PDF Option IMPORTANT DO NOT remove the USB flash memory from the USB direct interface until the printer has finished printing. Multiple Page Orientation Print Quality Collate Printing Methods...
Page 37: Driver And Software
 CUPS printer driver  Download the printer driver for Linux from http://solutions.brother.com/ or a link on the CD-ROM we have supplied. Depending on Linux distributions, the driver may not be available. Note • For more information about Linux printer driver, visit us at http://solutions.brother.com/.
Page 38 For the information on supported Linux distribution and to download the printer driver, visit us at http://solutions.brother.com/. You can also download the printer driver from a link on the supplied CD-ROM. If you download from a link on CD-ROM, click Install Other Drivers or Utilities, then click For Linux users on the screen menu.
Page 39 These settings are not available with the BR-Script printer driver for Windows These settings are not available with the Macintosh printer driver and the BR-Script printer driver for Macintosh. These settings are not available with the BR-Script printer driver for Macintosh.
Page 40: Features In The Printer Driver (For Windows )
Features in the printer driver (for Windows (For more information, see the Help text in the printer driver.) Note • The screens in this section are from Windows your operating system. • You can access the Printing Preferences dialog box by clicking Printing Preferences... in the General tab of the Printer Properties dialog box.
Page 41 Collate checked Media Type You can use the following types of media in your printer. For the best print quality, select the type of media that you wish to use. Plain Paper Thin Paper Env.
Page 42: Print Quality
Mono mode prints your document in 256 levels of gray.  Auto The printer checks the content of your documents for color. If color is detected, it prints in color. If no color content is detected, it prints in monochrome. The total printing speed may become slower. Note If the Cyan, Magenta or Yellow toner reaches the end of its life, choosing Mono will allow you to keep printing as long as the Black toner does not reach the end of its life.
Page 43: Settings Dialog
This is the default color mode. • Vivid The color of all elements are adjusted to become a more vivid color. • Auto The printer driver automatically selects the Color Mode type. • None Import  You can adjust the print configuration of a particular image by clicking settings. When you have finished adjusting the image parameters, such as brightness and contrast, you can import those settings as a print configuration file.
Page 44 Manual Duplex In this mode, the printer prints all the even numbered pages first. Then the printer driver will stop and show the instructions required to re-install the paper. When you click OK the odd numbered pages will be printed (See Manual duplex printing on page 19).
Page 45 Toner Save Mode (5)  Secure Print (6)  Administrator (7)  User Authentication (8) (HL-3075CW only)  Other Print Options (9) Scaling You can change the print image scaling. Reverse Print Check Reverse Print to rotate the data by 180 degrees.
Page 46 Use Watermark You can put a logo or text into your documents as a watermark. You can choose one of the preset watermarks, or you can use a bitmap file or text that you have created. When you use a bitmap file as a watermark, you can change the size of the watermark and put it anywhere you like on the page.
Page 47 Set Password Click here to change the password. User Authentication (HL-3075CW only) If you are restricted from PC Print by Secure Function Lock feature, you need to set your ID and PIN in the User Authentication dialog. Click Settings of the User Authentication and enter your ID and PIN. If your PC login name is registered to Secure Function Lock, you can check the Use PC Login Name box instead of entering your ID and PIN.
Page 48: Color Calibration
When you choose Printer Default, the timeout setting has been set to a specific time set at the factory, this can be altered in the driver or at the printer. Intelligent Sleep Mode automatically adjusts to the most suitable timeout setting depending on the frequency of your printer use.
Page 49 If you choose this setting, the paper curl may be reduced. If you are printing only a few pages, you do not need to choose this setting. We recommend that you change the printer driver setting in Media Type to a thin setting. Note This operation makes the temperature of the printer’s fusing process lower.
Page 50 Tray Settings tab Note From the Start menu, select Control Panel and then Printers and Faxes. Right-click the Brother HL-3075CW (HL-3045CN) series icon and select Properties to access the Tray Settings tab. You can define the paper size for each paper tray and auto detect the serial number in the Tray Settings tab as follows.
Page 51  Brother Solutions Center (1) The Brother Solutions Center (http://solutions.brother.com/) is a web site offering information about your Brother product including FAQs (Frequently Asked Questions), User’s Guides, driver updates and tips for using your printer.  Genuine Supplies website (2) You can visit our website for genuine Brother supplies by clicking this button.
Page 52: Using The Custom Monochrome Printer Driver (For Windows )
• The password must be between 5 and 25 characters. • You can unlock the restrict color printing setting by using the Color/Mono Lock feature of the printer driver. (See Administrator on page 42.) To unlock the driver for color printing, you will need the password you set at step b.
Page 53 (For more information, see the Help text in the printer driver.) Note • To use the BR-Script3 printer driver you must install the driver using the Custom Install from the CD-ROM. • The screens in this section are from Windows on your operating system.
Page 54  Paper/Quality tab Choose the Paper Source and Color. • Paper Source You can choose Automatically Select, Tray1 or Manual Feed. • Color Choose how to print color graphics either Black and White or Color. Driver and Software...
Page 55: Advanced Options
• If you want the calculations for color matching to be performed on the host computer before it sends the document to the printer, click ICM Handled by Host System. • If you want the calculations for color matching to be performed on your printer, click ICM Handled by Printer using printer calibration.
Page 56 If you still get the same error message after you try printing several times, add more memory. (See Installing extra memory on page 99.)  Media Type You can use the following types of media in your printer. For the best print quality, select the type of media that you wish to use. Plain Paper Thin Paper Env.
Page 57  Sleep Time When the printer does not receive data for a certain period of time, it enters sleep mode. In sleep mode, the printer acts as though it were turned off. When you choose Printer Default the timeout setting has been set to a specific time set at the factory, this can be altered in the driver or at the printer.
Page 58 If you choose this setting, the paper curl may be reduced.If you are printing only a few pages, you do not need to choose this setting. We recommend that you change the printer driver setting in Media Type to a thin setting.
Page 59 Driver and Software Ports tab Choose the port where your printer is connected or the path to the network printer you are using.
Page 60: Features In The Printer Driver (For Macintosh)
Features in the printer driver (for Macintosh) This printer supports Mac OS X 10.4.11, 10.5.x, 10.6.x Note The screens in this section are basically from Mac OS X 10.5.x. The screens on your Macintosh will vary depending on your operating system.
Page 61: Choosing Printing Options
 For Mac OS X 10.5.x and 10.6.x For more page setup options, click the disclosure triangle beside the Printer pop-up menu. Choosing printing options To control special printing features, choose the options in the Print dialog box. Driver and Software...
Page 62 Cover Page You can make the following cover page settings:  Print Cover Page If you want to add a cover page to your document, use this function.  Cover Page Type Choose a template for the cover page.  Billing Info If you want to add the billing information to the cover page, enter text in the Billing Info box.
Page 63 Secure Print: Secure documents are documents that are password protected when they are sent to the printer. Only the people who know the password will be able to print them. Since the documents are secured at the printer, you must enter the password using the control panel of the machine to print them.
Page 64: Print Settings
Print Settings You can change settings by choosing a setting in the Print Settings list: Basic tab  Media Type You can change the media type to one of the following: • Plain Paper • Thin Paper • Thick Paper •...
Page 65 256 levels of gray. • Auto The printer checks the content of your documents for color. If color is detected, it prints in color. If no color content is detected, it prints in monochrome. The total printing speed may become slower.
Page 66 Advanced tab  Color Mode You can change the color mode as follows: • Normal This is the Default color mode. • Vivid The color of all elements are adjusted to become a more vivid color. • None  Enhance Black Printing If a black graphic cannot be printed correctly, choose this setting.
Page 67 When you choose Printer Default the timeout setting has been set to a specific time set at the factory, this can be altered in the driver or at the printer. If you want to change the sleep time, choose Manual and then enter the time in the text box on the driver.
Page 68 Manual Duplex Printing Select Paper Handling.  For Mac OS X 10.4.x Choose Odd numbered pages. Turn the paper over and reload it in the tray, and then choose Even numbered pages and print.  For Mac OS X 10.5.x and 10.6.x Choose Odd only and print.
Page 69: Status Monitor
Status Monitor This reports the printer status (any errors that may happen with the printer) when printing. If you would like to turn the status monitor on, follow these steps:  For Mac OS X 10.4.11 Run the Printer Setup Utility (from the Go menu, choose Applications, Utilities), then choose the printer.
Page 70: Using The Br-Script3 Printer Driver (Postscript ® 3™ Language Emulation For Windows ® ) (Hl-3075Cw Only)
• To use the BR-Script3 printer driver on a Network, see the Network User’s Guide on the CD-ROM. • To use the BR-Script3 printer driver, you need to set the Emulation to BR-Script3 by using the control panel before connecting the interface cable. (See Print Menu on page 84.) Installing the BR-Script3 printer driver You need to install the BR-Script3 printer driver using the following instructions.
Page 71 Double-click the Printer Setup Utility icon. Click Add. Choose the printer name and make sure that Brother is shown in Printer Model (Print Using). Select the printer name that shows BR-Script in the Model Name (Model), and then click Add.
Page 72 From the Printer Setup Utility menu, choose Quit Printer Setup Utility.  For Mac OS X 10.5.x and 10.6.x From the Apple menu choose System Preferences. Click Print&Fax. Driver and Software...
Page 73 Click + which is located below the Printers section. Choose the Printer Name and choose Select a driver to use in Print Using, and then choose the Printer Name that shows BR-Script in model name, and then click Add. Quit System Preferences.
Page 74: Uninstalling The Printer Driver
• After uninstalling, we recommend that you restart your computer to remove files that were in use during the uninstall. Printer driver for Windows Click the Start button, point to All Programs, Brother and then to your printer name. Click UnInstall. Follow the instructions on the screen.
Page 75: Printer Driver For Macintosh
For Mac OS X 10.5.x and 10.6.x Log in as an ‘Administrator’. From the Apple menu, choose System Preferences. Click Print & Fax, then choose the printer you want to remove and remove it by clicking the – button. Click OK Delete Printer for Mac OS X 10.6.x users...
Page 76: Software
BRAdmin Professional 3 is a utility for more advanced management of network connected Brother devices. This utility can search for Brother products on your network and view the device status from an easy to read explorer style window that changes color identifying the status of each device. You can configure network...
Page 77 Web Based Management (web browser) is a utility for managing network connected Brother devices, using the HTTP (Hyper Text Transfer Protocol). This utility can view the status of Brother products on your network and configure the machine or network settings using a standard web browser that is installed on your computer.
Page 78: About Emulation Modes (Hl-3075Cw Only)
About emulation modes (HL-3075CW only) This printer has the following emulation modes. You can change the setting by using the control panel or Web Based Management (Web browser).  HP LaserJet Mode The HP LaserJet mode (or HP mode) is the emulation mode in which this printer supports the PCL6 language of the Hewlett-Packard LaserJet laser printer.
Page 79: Control Panel
Control Panel Control panel This printer has one back lit Liquid Crystal Display (LCD), seven buttons and two Light Emitting Diodes (LEDs) on the control panel. The LCD is a 16 character single line display. The illustration is based on HL-3075CW.
Page 80: Cancel
LCD. • If the printer is in Pause mode and you do not want to print the data left, press Cancel. Once the job has been canceled, the printer will return to the Ready state.
Page 81: Back
Back Pressing Back when the printer is in the Ready state takes it offline, and the LCD will show the control panel menu. Pressing Back allows you to return to the previous level from the current menu level. Back also allows you to choose the previous digit while setting numbers.
Page 82: Back Light (Hl-3075Cw Only)
Back light (HL-3075CW only) Light Green (General, Error, Setting) LCD messages The message on the LCD shows the current printer status during normal operation. Ready mark indicates the wireless signal strength with four levels. ( means middle, and means strong.) (HL-3075CW only) When an error has occurred, the type of error is displayed on the LCD message at first as shown below.
Page 83: Reprinting Documents
You can reprint the data from the last print job without sending it from the computer again. Note • Reprint function is not available when Secure Function Lock 2.0 (HL-3075CW only) is On. For more information about Secure Function Lock 2.0, see the Chapter 14 of the Network User’s Guide on the CD- ROM we have supplied.
Page 84: Printing Secure Data
Secure documents are protected by a password and only those people who know the password will be able to print the document. The printer will not print the document when you send it for printing. To print the document, you must use the control panel of the printer (with the password). Secure data will be deleted after printing once.
Page 85 Press OK or Go. Printing Ready Deleting secure data Choose the user name and the job you want to delete in steps a to d, and then choose Delete (instead of Print) in step e. Canceling the secure data job (printing secure data) If you want to cancel the current secure print job, press Cancel.
Page 86: Using The Control Panel Lcd Menu
+ or - to scroll faster. The blinking number is the one that you can change. For example: If you want to choose the paper size for Tray 1, as follows. Press any of the Menu buttons (+, -, OK or Back) to take the printer offline. Ready Machine Info.
Page 87: Menu Table
• Manual feed slot: Manual Feed Machine Info. Submenu Menu Selections Print Settings Print NetSetting Test Print Demo Print Print Font HP LaserJet (HL-3075CW only) BR-Script 3 Serial No. Version Main Version Sub Version RAM Size Page Count Total Color...
Page 88 Machine Info. (continued) Submenu Menu Selections Drum Count Black(K) Cyan(C) Magenta(M) Yellow(Y) Parts Life Drum Life Belt Life PF Kit1 Life Fuser Life Reset Parts Life Drum Unit (Appears only when replacement parts have been changed) Belt Unit The factory settings are shown in Bold with an asterisk. Paper Tray Submenu Options...
Page 89 Input Buffer The factory settings are shown in Bold with an asterisk. Print Menu Submenu Menu Selections Emulation (HL-3075CW only) Auto Continue Output Color (HL-3075CW only) Media Type (HL-3075CW only) The factory settings are shown in Bold with an asterisk.
Page 90 Print Menu (continued) Submenu Menu Selections Paper (HL-3075CW only) Copies (HL-3075CW only) Orientation (HL-3075CW only) Print Position X Offset Y Offset Auto FF (HL-3075CW only) The factory settings are shown in Bold with an asterisk. Options Descriptions Sets the size of paper.
Page 91 Print Menu (continued) Submenu Menu Selections HP LaserJet Font No. Font Pitch (HL-3075CW only) Font Point Symbol Set Table Print Auto LF Auto CR Auto WRAP Auto SKIP Left Margin Right Margin Top Margin Bottom Margin Lines BR-Script 3 Error Print...
Page 92 Network for HL-3045CN users Submenu Menu Selections TCP/IP Boot Method IP Address Subnet Mask Gateway IP Boot Tries APIPA IPv6 Ethernet Restores all network settings of the internal print server to the factory default. Factory Reset The factory settings are shown in Bold with an asterisk. On connection to the network, if the machine's 'Boot Method' is 'Auto' the machine will attempt to automatically set the IP address and Subnet Mask from a boot server such as DHCP or BOOTP.
Page 93 Network for HL-3075CW users Submenu 1 Submenu 2 Menu Selections Wired LAN TCP/IP Boot Method IP Address Subnet Mask Gateway IP Boot Tries APIPA IPv6 Ethernet Restores wired network settings of the internal print server to the factory default. Set to...
Page 94: Color Correction
Reset Menu Display Shows Description Resets the printer and restores all printer settings (including command settings) to settings Reset Printer you have previously made with the control panel buttons. Resets the printer and restores the printer settings (including command settings) to the Factory Reset factory default settings.
Page 95 Sets the format of the index for direct Simple*/Details print. If you choose Details, printing time will be longer. (See Printing data from a USB flash memory drive with direct print (HL-3075CW only) on page 27.) Control Panel...
Page 96 PictBridge (HL-3075CW only) Submenu Menu Selections Paper Size Orientation Date&Time File Name Print Quality The factory settings are shown in Bold with an asterisk. Options Descriptions Sets the size of paper for PictBridge. Letter*/A4/B5/A5/B6/A6 <For Letter,A4,B5> This printer can print pages in portrait...
Page 97 Press any of the Menu buttons (+, -, OK or Back) to take the printer offline. Press + or - to choose Network. Select ab or OK Network (HL-3075CW only) Press + or - to choose Wired LAN or WLAN. Wired LAN Press OK. TCP/IP Press OK.
Page 98: Default Settings
The printer will restart automatically. Factory Reset You can partially reset the machine back to its default printer settings. The settings that will not be reset are the Interface, Local Language, Reprint, Set Registration, Setting Lock, Secure Function Lock 2.0 (HL-3075CW only) and the Network settings: Press + or - to choose Reset Menu.
Page 99 Settings Reset This operation will reset all the machine settings back to the settings that were set at the factory: Disconnect the network cable from the printer; otherwise the network settings (such as IP address) will not be reset. Press + or - to choose Reset Menu. Press OK.
Page 100: Frequency
See Color Calibration on page 43. If you print using the Macintosh printer driver, you need to perform the calibration using the status monitor. See Status Monitor on page 64 for how to turn the status monitor on.
Page 101: Auto Registration
Press + or - to choose Reset. Press OK. Reset Press OK again. Auto Registration You can adjust the print position of each color automatically. Press + or - to choose Color Correction. Press OK. Select ab or OK Color Correction Press + or - to choose Auto Regist..
Page 102: Manual Registration
Manual Registration Print Chart You can print the color registration chart to manually check the registration of the colors. Press + or - to choose Color Correction. Press OK. Select ab or OK Color Correction Press + or - to choose Manual Regist.. Press OK. Manual Regist.
Page 103: Option
Option SO-DIMM The printer has 32 MB (HL-3045CN) or 64 MB (HL-3075CW) of standard memory and one slot for optional memory expansion. You can expand the memory up to 544 MB (HL-3045CN) or 576 MB (HL-3075CW) by installing a Dual In-line Memory Module (SO-DIMM).
Page 104: Installing Extra Memory
Remove the plastic (1) and then the metal (2) SO-DIMM covers. Unpack the SO-DIMM and hold it by its edges. CAUTION To prevent damage to the printer from static electricity, DO NOT touch the memory chips or the board surface. Option...
Page 105 Insert the SO-DIMM diagonally (1), then tilt it toward the interface board until it clicks into place (2). Put the metal (2) and then the plastic (1) SO-DIMM covers back on. Reconnect the interface cable to your printer. Plug the printer back in, and then turn on the power switch. Note To make sure that you have installed the SO-DIMM properly, you can print the printer settings page that shows the current memory size.
Page 106: Routine Maintenance
The following messages appear on the LCD in the Ready state. These messages provide advanced warnings to replace the consumable items before they reach the end of their life. To avoid any inconvenience, you may want to buy spare consumable items before the printer stops printing. LCD messages...
Page 107 You will need to replace certain parts and clean the printer regularly. LCD messages Consumable item to replace Toner cartridge Replace Toner 4 Drum units Replace Drums 1 Drum unit Replace Drum (X) X = C, M, Y, K C = Cyan...
Page 108: Toner Cartridges
• Go to http://www.brother-usa.com/environment/ for instructions on how to return the used toner cartridge to the brother collection program. If you choose not to return your used toner cartridge, please discard the used toner cartridge according to local regulations, keeping it separate from domestic waste. If you have questions, call your local waste disposal office.
Page 109 Replacing the toner cartridges Note • To ensure high quality printing, we recommend that you use only genuine Brother toner cartridges. When you want to buy toner cartridges, call your dealer. • We recommend that you clean the printer when you replace the toner cartridge. See Cleaning on page 127.
Page 110 DO NOT use cleaning materials that contain ammonia, alcohol, any type of spray, or any type of flammable substance to clean the outside or inside of the machine. Doing this may cause a fire or electrical shock. See Cleaning on page 127 for how to clean the printer. Be careful not to inhale toner.
Page 111 • Go to http://www.brother-usa.com/environment/ for instructions on how to return the used toner cartridge to the brother collection program. If you choose not to return your used toner cartridge, please discard the used toner cartridge according to local regulations, keeping it separate from domestic waste. If you have questions, call your local waste disposal office.
Page 112 IMPORTANT • Wait to unpack the toner cartridge until immediately before you put it in the printer. If toner cartridges are left unpacked for a long time the toner life will be shortened. • If an unpacked drum unit is put in direct sunlight or room light, the unit may be damaged.
Page 113 IMPORTANT For UK and other countries Brother machines are designed to work with toner of a particular specification and will work to a level of optimum performance when used with genuine Brother branded toner cartridges. Brother cannot guarantee this optimum performance if toner or toner cartridges of other specifications are used. Brother does not therefore recommend the use of cartridges other than genuine Brother branded cartridges with this machine.
Page 114 Pull off the protective cover. Put the new toner cartridge firmly into the drum unit until you hear it lock into place. Note Make sure that you put in the toner cartridge properly or it may separate from the drum unit. Routine Maintenance...
Page 115 Slide the drum unit and toner cartridge assembly into the printer. Make sure that you match the toner cartridge color to the same color label on the printer. Close the top cover of the printer. Turn the printer power switch back on.
Page 116: Drum Units
(unless you have replaced an individual drum [DR-210CL-BK for black and DR-210CL-CMY for Color] for reasons other than reaching its rated life). For your convenience, Brother sells the drum units as a set of four (DR-210CL).
Page 117 • While removing the drum unit, handle it carefully because it may contain toner. • We recommend that you clean the printer when you replace the drum unit. See Cleaning on page 127. Turn off the printer power switch. Fully open the top cover by lifting up on the handle (1).
Page 118 DO NOT use cleaning materials that contain ammonia, alcohol, any type of spray, or any type of flammable substance to clean the outside or inside of the machine. Doing this may cause a fire or electrical shock. See Cleaning on page 127 for how to clean the printer. Be careful not to inhale toner.
Page 119 • Go to http://www.brother-usa.com/environment/ for instructions on how to return the used toner cartridge to the brother collection program. If you choose not to return your used toner cartridge, please discard the used toner cartridge according to local regulations, keeping it separate from domestic waste. If you have questions, call your local waste disposal office.
Page 120 Unpack the new drum unit and pull off the protective cover. IMPORTANT Wait to unpack a drum unit until immediately before you put it in the printer. Exposure to direct sunlight or room light may damage the drum unit. Put the toner cartridge firmly into the new drum unit until you hear it lock into place.
Page 121 Slide the drum unit and toner cartridge assembly into the printer. Make sure that you match the toner cartridge color to the same color label on the printer. Close the top cover of the printer. When you replace a drum unit with a new one, you need to reset the drum counter by completing the following steps: Turn the printer power switch back on.
Page 122: Belt Unit
• DO NOT touch the surface of the belt unit. If you touch it, it could degrade print quality. • Damage caused by incorrect handling of the belt unit may void your warranty. Replacing the belt unit Turn off the printer power switch. Fully open the top cover by lifting up on the handle (1). Routine Maintenance...
Page 123 • We recommend that you place the drum unit and toner cartridge assembly on a clean, flat surface with a sheet of disposable paper or cloth underneath it in case you accidentally spill or scatter toner. • To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration.
Page 124 Hold the green handle of the belt unit and lift the belt unit up, then pull it out. IMPORTANT To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations. Unpack the new belt unit and put the new belt unit in the printer. Routine Maintenance...
Page 125 Slide each drum unit and toner cartridge assembly into the printer. Make sure that you match the toner cartridge color to the same color label on the printer. Repeat this for all the drum unit and toner cartridge assemblies. Close the top cover of the printer.
Page 126: Waste Toner Box
Waste toner box Order No. WT-200CL The life of a waste toner box is approximately 50,000 A4 or Letter size single-sided pages. WT Box End Soon message WT Box End Soon If the LCD shows WT Box End Soon, it means the waste toner box is near the end of its life. Buy a new waste toner box and have it ready before you get a Replace WT Box message.
Page 127 Replacing the waste toner box Turn off the printer power switch. Fully open the top cover by lifting up on the handle (1). Take out all the drum unit and toner cartridge assemblies. Routine Maintenance...
Page 128 • We recommend that you place the drum unit and toner cartridge assembly on a clean, flat surface with a sheet of disposable paper or cloth underneath it in case you accidentally spill or scatter toner. • To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration.
Page 129 Routine Maintenance IMPORTANT To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations. Remove the orange packing material and discard it. Note This step is only necessary when you are replacing the waste toner box for the first time. The orange packing is installed at the factory to protect your machine during shipment.
Page 130 Hold the green handle of the waste toner box and remove the waste toner box from the printer. IMPORTANT Handle the waste toner box carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water at once.
Page 131 Put the belt unit back in the printer. Slide each drum unit and toner cartridge assembly into the printer. Make sure that you match the toner cartridge color to the same color label on the printer. Repeat this for all the drum unit and toner cartridge assemblies.
Page 132: Cleaning
Clean the outside and inside of the printer regularly with a dry, lint-free cloth. When you replace the toner cartridge or the drum unit, make sure that you clean the inside of the printer. If printed pages are stained with toner, clean the inside of the printer with a dry, lint-free cloth.
Page 133 Pull the paper tray completely out of the printer. Wipe the outside of the printer with a dry, lint-free cloth to remove dust. Remove anything that is stuck inside the paper tray. Wipe the inside of the paper tray with a dry, lint-free cloth to remove dust.
Page 134: Cleaning The Led Head
Put the paper tray back in the printer. Plug the printer back in, and then turn on the power switch. Cleaning the LED head Turn off the printer power switch and then unplug the printer. Fully open the top cover by lifting up on the handle (1).
Page 135: Cleaning The Corona Wires
Plug the printer back in, and then turn on the power switch. Cleaning the corona wires If you have print quality problems, clean the corona wires as follows: Turn off the printer power switch. Fully open the top cover by lifting up on the handle (1). Routine Maintenance...
Page 136 • We recommend that you place the drum unit and toner cartridge assembly on a clean, flat surface with a sheet of disposable paper or cloth underneath it in case you accidentally spill or scatter toner. • To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration.
Page 137 Be sure to return the tab to the home position (a) (1). If you do not, printed pages may have a vertical stripe. Slide the drum unit and toner cartridge assembly into the printer. Make sure that you match the toner cartridge color to the same color label on the printer.
Page 138: Cleaning The Drum Unit
Cleaning the drum unit Small spots on the printed pages If your printout has any small white or colored spots, follow the steps below to solve the problem. Open the manual feed slot cover. Using both hands, slide the manual feed slot paper guides to the width of the paper that you are going to use.
Page 139 • Do not put more than one piece of paper in the manual feed slot at any one time, as it may cause a jam. • If you put paper in the manual feed slot before the printer is in the Ready state, an error may occur and the printer will stop printing.
Page 140 If your printout has colored spots at 94 mm (3.7 in.) intervals, follow the steps below to solve the problem. Turn off the printer power switch. Fully open the top cover by lifting up on the handle (1). See the print sample to identify the color causing the problem. The color of the spots is the color of the drum you should clean.
Page 141 • We recommend that you place the drum unit and toner cartridge assembly on a clean, flat surface with a sheet of disposable paper or cloth underneath it in case you accidentally spill or scatter toner. • To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration.
Page 142 Put the print sample in front of the drum unit, and find the exact position of the poor print. Turn the drum unit gear by hand while looking at the surface of the OPC drum (1). When you have found the mark on the drum that matches the print sample, wipe the surface of the OPC drum with a dry cotton swab until the dust or glue on the surface comes off.
Page 143 Make sure that you put in the toner cartridge properly or it may separate from the drum unit. Slide each drum unit and toner cartridge assembly into the printer. Make sure that you match the toner cartridge color to the same color label on the printer.
Page 144: Cleaning The Paper Pick-Up Roller
Cleaning the paper pick-up roller Turn off the printer power switch and then unplug the printer. Pull the paper tray completely out of the printer. Routine Maintenance...
Page 145 Tightly wring out a lint-free cloth soaked in lukewarm water, and then wipe the separator pad (1) of the paper tray with it to remove dust. Wipe the two pick-up rollers (1) inside of the printer to remove dust. Put the paper tray back in the printer.
Page 146: Troubleshooting
Troubleshooting You can correct most problems by yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at http://solutions.brother.com/. Identifying your problem First, check the following:  The AC power cord is connected properly and the printer is turned on.
Page 147: Lcd Messages
If you need more help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at http://solutions.brother.com/. If you cannot clear the problem, call the dealer you bought the printer from or Brother Customer Service. Note The LCD names for the paper trays are as follows.
Page 148 Print Unable 1A minutes to remove any condensation from inside the machine, then close the top cover and turn it on again. If this does not clear the error, call your dealer or a Brother Customer Service. Open the back cover (back output tray) to let the printed paper out on the back out put tray.
Page 149: Maintenance Messages
Call service messages Call service message Action Turn off the printer. Wait a few seconds, then turn it on again. If this does not clear the Print Unable ## (Except Print Unable 1A) error, call your dealer or a Brother Customer Service.
Page 150: Paper Handling
Paper handling First, make sure that you are using paper that meets Brother recommended paper specifications. (See About paper on page 1.) Problem Recommendation The printer does not feed  paper.    The printer does not feed paper ...
Page 151: Paper Jams And How To Clear Them
Paper jams and how to clear them If paper jams inside the printer, the printer will stop. One of the following LCD messages will appear to tell you where to find the jammed paper.  Jam Tray 1 (1) Paper jam in the standard paper tray (Tray 1). (See page 147.) ...
Page 152: Jam Tray 1 (Paper Jam Inside The Paper Tray)
Jam Tray 1 (Paper jam inside the paper tray) Jam Tray 1 If a paper jam occurs inside the paper tray, follow these steps: Pull the paper tray completely out of the printer. Use both hands to slowly pull out the jammed paper. Note Pulling out the jammed paper downward allows you to remove the paper easier.
Page 153: Jam Rear (Paper Jam Behind The Back Cover)
Open the back cover. CAUTION After you have just used the printer, some internal parts will be extremely hot. Wait at least 10 minutes for the printer to cool down before continuing to the next step. Pull the green tabs at the left and right hand sides toward you and fold down the fuser cover (1).
Page 154 Using both hands, gently pull the jammed paper out of the fuser unit. Close the fuser cover (1) and lift the green tabs at the left and right hand sides. Close the back cover. Plug the printer back in, and then turn on the power switch. Troubleshooting...
Page 155: Jam Inside (Paper Jam Inside The Printer)
Fully open the top cover by lifting up on the handle (1). CAUTION After you have just used the printer, some internal parts will be extremely hot. Wait at least 10 minutes for the printer to cool down before continuing to the next step.
Page 156 • We recommend that you place each drum unit and toner cartridge assembly on a clean, flat surface with a sheet of disposable paper or cloth underneath it in case you accidentally spill or scatter toner. • To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration.
Page 157 Slide each drum unit and toner cartridge assembly into the printer. Make sure that you match the toner cartridge color to the same color label on the printer for all four drum unit and toner cartridge assemblies. Close the top cover of the printer.
Page 158: Improving The Print Quality
If you have a print quality problem, print a test page first (see Machine Info. on page 82). If the printout looks good, the problem is probably not the printer. Check the interface cable or try the printer on another computer.
Page 159 FAQs and troubleshooting tips.  Put in a new drum unit. (See Replacing the drum units on page 112.) To identify the color of the drum unit, visit us at http://solutions.brother.com/ to view our FAQs and troubleshooting tips. ...
Page 160 FAQs and troubleshooting tips.  Put in a new drum unit. (See Replacing the drum units on page 112.) To identify the color of the drum unit, visit us at http://solutions.brother.com/ to view our FAQs and troubleshooting tips. ...
Page 161 FAQs and troubleshooting tips.  If the problem continues, put in a new drum unit. (See Replacing the drum units on page 112.) To identify the color of the drum unit, visit us at http://solutions.brother.com/ to view our FAQs and troubleshooting tips. Troubleshooting...
Page 162 Identify the color causing the problem and put in a new drum unit. (See Replacing the drum units on page 112.) To identify the color of the drum unit, visit us at http://solutions.brother.com/ to view our FAQs and troubleshooting tips.
Page 163 Identify the color causing the problem and put in a new drum unit. (See Replacing the drum units on page 112.) To identify the color of the drum unit, visit us at http://solutions.brother.com/ to view our FAQs and troubleshooting tips.
Page 164 Macintosh printer driver).  If you do not use the printer often, the paper may have been in the paper tray too long. Turn over the stack of paper in the paper tray. Also, fan the paper stack and then rotate the paper 180 in the paper tray.
Page 165: Solving Print Problems
For problems concerning using your printer on a Network, see the Network User’s Guide on the CD-ROM we have supplied. The latest Network User's Guide in PDF format is available by accessing the Brother Solutions Center (http://solutions.brother.com/). Adverse conditions on the power connection (such as lightning or a power surge) may have triggered the printer's internal safety mechanisms.
Page 166: Other Problems
The printer cannot print EPS data that includes binary. Make sure the printer is powered on and that no error messages on the LCD. Make sure that the USB interface cable is connected directly to the Macintosh and that it is connected to the USB port of the printer.
Page 167: A Appendix
Linux The printing speed may change depending on the type of document you print. Print speed may be slower when the printer is connected by wireless LAN. From standard paper tray. First print out time may change if the machine is calibrating or registering itself.
Page 168: Controller
See the Network User's Guide locator on the CD-ROM for details on the supported network protocols. ® Brother original Windows and Macintosh utility for printer and print server management. Install from the supplied CD-ROM for Windows or download from the Brother Solutions Center at http://solutions.brother.com/ for Macintosh. ®...
Page 169: Software
Data that includes a JBIG2 image file, JPEG2000 image file, or a transparency files is not supported. ® See Creating a PRN or PostScript 3™ (HL-3075CW only) file for direct printing on page 28. HL-3075CW ® XP Home Edition, Windows ®...
Page 170: Control Panel
Paper tray Media sizes Manual feed slot Paper tray Legal size paper is not available in some regions outside the USA and Canada. HL-3075CW 1 line, 16 Digits, 1 color HL-3045CN 1 sheet 250 sheets 100 sheets 1 sheet...
Page 171: Supplies
Dimensions / weights Model Dimensions (W  D  H) Weights HL-3045CN HL-3075CW Approx. 2,200 pages A4/Letter pages Approx. 1,400 pages A4/Letter pages Approx. 15,000 pages (1 page / job) Approx. 50,000 pages A4/Letter pages Approx. 50,000 pages A4/Letter pages HL-3045CN 409 ...
Page 172: Other
LpAm = 30 dB (A) Monochrome LWAd = 6.34 Bell (A) Color LWAd = 6.29 Bell (A) LWAd = 3.64 Bell (A) Appendix HL-3075CW Average 480W at 25 C (77 F) Average 70 W at 25 C (77 F) Average 10 W...
Page 173: Computer Requirements
OS X 10.4.11 and 10.5.x PowerPC Operating System OS X 10.6.x ® Microsoft Internet Explorer 5.5 or greater. Third party USB ports are not supported. For the latest driver updates, visit http://solutions.brother.com/. Processor Minimum Speed Minimum 128 MB ® ® Intel Pentium...
Page 174: Important Information For Choosing Your Paper
Though most plain paper for copying is long grain, some is short grain. We recommend that you use long grain paper for this printer. Short grain paper is too weak for the paper transport of the printer.
Page 175 Print surface The characteristics of the face side and reverse side of a sheet of paper may vary a little. Usually, the opening side of the paper ream package is the print side. Follow the indications on the paper package. Typically, the print side is indicated by an arrow. Moisture content Moisture content is the amount of water left in the paper after manufacture.
Page 176 Paper size Paper size Letter Legal Executive A5 (Long Edge) Envelope Monarch Envelope Com-10 Envelope DL Envelope C5 B5 (JIS) B5 (ISO) B6 (JIS) B6 (ISO) Folio A4 Long Envelope DL-L 3  5 Hagaki Postcard with the size specified by Japan Post Service Co., LTD 210 ...
Page 177: Symbol And Character Sets (Hl-3075Cw Only)
TCP/IP and NetBIOS, you can also enter the NetBIOS name of the print server. The NetBIOS name can be seen on the printer settings page. The NetBIOS name assigned is the first 15 characters of the node name and by default it will appear as “BRNxxxxxxxxxxxx”...
Page 178: Symbol And Character Sets List
Symbol and character sets list OCR symbol sets When you choose the OCR-A or OCR-B font, the matching symbol set is always used. OCR A (0O) OCR B (1O) HP LaserJet mode ABICOMP Brazil / Portugal (13P) Desktop (7J) HP German (0G) ISO Latin1 (0N) ISO Latin5 (5N) ISO2 IRV (2U)
Page 179 HP LaserJet mode PS Text (10J) Roman9 (4U) Russian-GOST (12R) Roman8 (8U) Roman Extension (0E) Symbol (19M) Appendix...
Page 180: Quick Reference For Bar Code Control Commands (Hl-3075Cw Only)
Quick reference for bar code control commands (HL-3075CW only) The printer can print bar codes in the HP LaserJet emulation modes. Print bar codes or expanded characters Code ESC i 27 105 1B 69 Format: ESC i n ... n \ Creates bar codes or expanded characters according to the segment of parameters ‘n ...
Page 181 n = ‘t134’ or ‘T134’ This parameter selects the bar code mode as shown above. When n is ‘t5’ or ‘T5’ the bar code mode (EAN 8, EAN 13, or UPC A) varies according to the number of characters in the data. Bar code, expanded character, line block drawing and box drawing n = ‘s0’...
Page 182 Human readable line OFF All others This parameter shows whether the printer prints the human readable line below the bar code. Human readable characters are always printed with OCR-B font of 10 pitch and all the current character style enhancements are masked. The default setting is determined by the bar code mode selected by ‘t’ or ‘T’.
Page 183: Expanded Character Rotation
Bar code, expanded character, line block drawing and box drawing height n = ‘hnnn’, ‘Hnnn’, ‘dnnn’, or ‘Dnnn’ 1 EAN13, EAN8, UPC-A, ISBN (EAN13, EAN8, UPC-A), ISBN (UPC-E): 22 mm 2 UPC-E: 18 mm 3 Others: 12 mm Expanded characters i 2.2 mm (preset) Line block drawing and box drawing i 1 dot This parameter shows the height of bar codes or expanded characters as shown above.
Page 184 A number of characters other than those stated above will cause a data error that results in the bar code data being printed as normal print data. If the check digit is not correct, the printer decides the correct check digit automatically so that the correct bar code data will be printed. When EAN13 is selected, adding ‘+’...
Page 185: Box Drawing
 When EAN 128 set A, set B or set C is selected with the parameter ‘t132’ or ‘T132’, ‘t133’ or ‘T133’ or ‘t134’ or ‘T134’ The same rules apply as for ‘t12’ or ‘T12’, ‘t13’ or ‘T13’, or ‘t14’ or ‘T14’. Box drawing ESC i ...
Page 186 Table of Code(EAN) 128 set C Code(EAN) 128 set C describes an original command. The correspondence table is as follows. No. Code 128 Set C Input command No. Code 128 Set C Input command 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08...
Page 187 Appendix Example Program Listings WIDTH "LPT1:",255 'CODE 39 LPRINT CHR$(27);"it0r1s0o0x00y00bCODE39?\"; 'Interleaved 2 of 5 LPRINT CHR$(27);"it1r1s0o0x00y20b123456?\"; 'FIM LPRINT CHR$(27);"it3r1o0x00y40bA\"; 'Post Net LPRINT CHR$(27);"it4r1o0x00y60b1234567890?\"; 'EAN-8 LPRINT CHR$(27);"it5r1o0x00y70b1234567?\"; 'UPC-A LPRINT CHR$(27);"it5r1o0x50y70b12345678901?\"; 'EAN-13 LPRINT CHR$(27);"it5r1o0x100y70b123456789012?\"; 'UPC-E LPRINT CHR$(27);"it6r1o0x150y70b0123456?\"; 'Codabar LPRINT CHR$(27);"it9r1s0o0x00y100bA123456A\"; 'Code 128 set A LPRINT CHR$(27);"it12r1o0x00y120bCODE128A12345?\";...
Page 188: Libtiff Copyright And License
Appendix Libtiff Copyright and License Use and Copyright Copyright© 1988-1997 Sam Leffler Copyright© 1991-1997 Silicon Graphics, Inc. Permission to use, copy, modify, distribute, and sell this software and its documentation for any purpose is hereby granted without fee, provided that (i) the above copyright notices and this permission notice appear in all copies of the software and related documentation, and (ii) the names of Sam Leffler and Silicon Graphics may not be used in any advertising or publicity relating to the software without the specific, prior written permission of Sam Leffler and Silicon Graphics.
Page 189: B Appendix (For Europe And Other Countries)
Frequently asked questions (FAQs) The Brother Solutions Center is our one-stop resource for all your printer needs. You can download the latest drivers, software and utilities, read FAQs and troubleshooting tips to learn how to get the most from your Brother product.
Page 190: C Appendix (For Usa And Canada)
FAQs (frequently asked questions) The Brother Solutions Center is our one-stop resource for all your printer needs. You can download the latest software and utilities and read FAQs and troubleshooting tips to learn how to get the most from your Brother product.
Page 191 1, rue Hotel de Ville Dollard-des-Ormeaux, PQ, Canada H9B 3H6 Service center locator (USA only) For the location of a Brother authorized service center, call 1-877-BROTHER (1-877-276-8437). Service center locations (Canada only) For the location of a Brother authorized service center, call 1-877-BROTHER Internet addresses Brother Global Web Site: http://www.brother.com/...
Page 192 Visa, MasterCard, Discover, or American Express credit card, you can order supplies directly from Brother. (You can visit us online for a complete selection of the Brother accessories and supplies that are available for purchase.)
Page 193: Index
Belt unit ... 117 Booklet printing ...22 BRAdmin Light ... 71 BRAdmin Professional ... 71 Brother Numbers (Europe and other countries) ... 184 Brother Numbers (USA/Canada) ... 185 BRPrint Auditor ... 72 BR-Script 3 mode ... 73 BR-Script3 ... 48 Buttons ...
Page 194 Network software ... 71 Paper ...1 Paper handling ... 165 Paper jams ... 146 Paper Tray ... 83 PCL printer driver ... 35 PictBridge ...23 Plain paper ... 2 Print Menu ... 84 Print quality ... 37 Printer driver ...32 Processor ...

This manual is also suitable for:

Hl-3045cn

Brother HL-3075CW User Manual

1 Printing Methods

2 Driver and Software

3 Control Panel

4 Option

5 Routine Maintenance

6 Troubleshooting

A Appendix

B Appendix (For Europe and Other Countries)

C Appendix (For USA and Canada)

Index

Quick Links

Related Manuals for Brother HL-3075CW

Summary of Contents for Brother HL-3075CW

This manual is also suitable for:

Table of Contents