Advertisement
2. INTRODUCTION
Robust aluminium design with built-in spring loaded telescopic mounting brackets. Both brackets can rotate 360° individually making
it easy to direct the light where required. 63 SMD LED's have two options on light settings; full - 1000lm, half - 500lm. Includes battery
level indicator, mains charger and USB lead.
3. SPECIFICATION
Model No .................................................................. LED138
Battery ........................................................3.7V 4.4Ah Li-ion
LED Quantity..................................................... 63 SMD LED
Lumen Output ..................................................... 500/1000lm
Min./Max length. .............................................. 1200/1800mm
Charging Time .............................................................. 4.5hrs
Operating Time ...................................... Low / High : 3 / 6hrs
Nett weight .................................................................... 0.9kg
4. CHARGING
4.1.
The battery fitted to this lamp is considered to be a consumable item and its ability to accept charge will reduce over time. We will
warranty it against mechanical and electrical defect for a period of one year, this does not cover fair wear and tear. If the battery is not
properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace the
battery even if it is less than one year old.
4.2.
Connect the charger cable into the charging port on the lamp, see fig.1. Plug into power supply and turn on, the charge LEDs on the lamp
will light as the battery charges. When fully charged all three green lamps will be lit.
4.3.
When the battery has fully charged (approx 4.5 hrs) disconnect from mains supply.
NOTE: The Lithium battery does not suffer from memory effect and once fully charged may be stored for up to six months without
another charge.
5. OPERATION
5.1.
Place the hook at the end of the lamp over one edge of the bonnet and gently pull the other hook towards the other side of the
bonnet.
5.2.
Steady the lamp with one hand, whilst extending the hook over the other side of the bonnet.
5.3.
Rotate the lamp to provide best illumination of work being undertaken.
5.4.
To use the lamp, scroll through the three settings using the on/off switch above the power socket. Press once for 100% output, once more
for 50% output and a third press to turn lamp off. The charge status LEDs will light when the on/off switch is pressed or whilst charging.
6. MAINTENANCE
6.1.
Keep lamp clean and check for damage before every use. If damage is observed, remove from use until unit is repaired.
Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
BATTERY REMOVAL / REPLACEMENT
Remove the screws in the black section of the lamp control section to remove the batteries.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey Ltd's Batteries Producer Registration Number (BPRN) is BPRN00705.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
fig.1
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
LED138
Issue 1
29/03/19
Advertisement
