Yellowtec MIKA Studio Light Briefing Book
  1. Manuals
  2. Brands
  3. Yellowtec Manuals
  4. Lighting Equipment
  5. MIKA Studio Light
  6. Briefing book

Yellowtec MIKA Studio Light Briefing Book

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
m!ka
briefing
book
1

Advertisement

Table of Contents
loading

Summary of Contents for Yellowtec MIKA Studio Light

  • Page 1 m!ka briefing book...
  • Page 2 Thank you for choosing Yellowtec products. Enjoy m!ka, the most exciting support system for microphones and monitors. m!ka is robust, sleek and flexible. All components are designed to fit with each other and can be combined in multiple ways. Check this Briefing Book to get initial infor­...

  • Page 3: Table Of Contents

    Briefing Book Content m!ka Mic Arm m!ka Studio Light MMS PDM Kit MMS Power Sting MMS Ceiling Mount MMS Wall Mount MMS Monitor Mount m!ka QuickFix MMS Cable Clamp MMS Safety Stop m!ka Monitor Arm m!ka Bushing m!ka Pole Adapter m!ka Table Clamp m!ka Table Through Mount m!ka Table Top Mount...

  • Page 4: M!Ka Mic Arm

    m!ka Mic Arm „On Air“ Audio Shield RED = High BLU = Low N/C N/C Cut Off ! Audio Shield RED = High 5/8“ BLU = Low BLK = 0V Remarks YEL = 12-24 VDC...
  • Page 5 m!ka Mic Arm Audio Shield RED = HIGH BLU = LOW Audio Shield RED = HIGH 5/8“ BLU = LOW Remarks...
  • Page 6 m!ka Mic Arm (all models) Remarks...
  • Page 7 m!ka Mic Arm (all models)

  • Page 8: M!Ka Studio Light

    m!ka Studiolight Remarks...
  • Page 9 m!ka Studiolight Remarks...
  • Page 10 m!ka Studiolight Remarks...
  • Page 11 m!ka Studiolight Remarks...

  • Page 12: Mms Pdm Kit

    m!ka MMS PDM­Kit Remarks...

  • Page 13: Mms Power Sting

    m!ka Power Sting Remarks...

  • Page 14: Mms Ceiling Mount

    m!ka MMS Ceiling Mount Remarks...

  • Page 15: Mms Wall Mount

    m!ka Wall Mount Remarks...

  • Page 16: Mms Monitor Mount

    m!ka MMS Monitor Mount Remarks...
  • Page 17 m!ka MMS Monitor Mount Remarks...

  • Page 18: M!Ka Quickfix

    m!ka MMS QuickFix...
  • Page 19 m!ka MMS QuickFix Remarks...

  • Page 20: Mms Cable Clamp

    m!ka MMS Cable Clamp Remarks...

  • Page 21: Mms Safety Stop

    m!ka MMS Safety Stop STOP Remarks...

  • Page 22: M!Ka Monitor Arm

    m!ka MMS Monitor Arm (Friction) Remarks...

  • Page 23: M!Ka Bushing

    m!ka Bushing 22 mm Remarks...

  • Page 24: M!Ka Pole Adapter

    m!ka MMS Pole Adapter...

  • Page 25: M!Ka Table Clamp

    m!ka Table Clamp Remarks...

  • Page 26: M!Ka Table Through Mount

    m!ka Table Through Mount...

  • Page 27: M!Ka Table Top Mount

    m!ka Table Top Mount Remarks...

  • Page 28: Mms Wall Bracket

    m!ka Wall Bracket Remarks...

  • Page 29: Mms System Wall

    m!ka System Wall Adapter...

  • Page 30: M!Ka Paddock

    m!ka PadDock Remarks...
  • Page 31 m!ka PadDock min 160mm max 300mm Remarks...

  • Page 32: M!Ka Copy Stand

    m!ka Copy Stand...
  • Page 33 m!ka Copy Stand Remarks...
  • Page 34 • EN 55015 • EN 61547 • EN 61000-3-2 • EN 61000-3-3 • EN 60589-1 according to the requirements of directives • 2006/95/EG • 2004/108/EG For Yellowtec Thum + Mahr GmbH Heinrich-Hertz-Str. 1-3 D-40789 Monheim am Rhein Monheim, 12.08.2013 Hanno Mahr, MD...
  • Page 35 Page 4 - We suggest to use XLR-5 pin connectors for microphone signal and on air light feed on lower end of cable and XLR-3 type connectors for microphone on upper end of cable. - When installing the connector on upper end cut off the black and yellow wires. They are not connected and do not carry any voltage.
  • Page 36 m!ka Remarks - Never pull the knurled screws too tight. They may break and the joints may squeak. Instead re-adjust the screw inside the bottom as in Step 1. - If necessary, use Teflon spray to unsqueak the joints. Page 8 - Make sure the bolt at the bottom of your m!ka Studio Light has its black plastic sleeve on.
  • Page 37 hole of 12mm diameter for the PDM Kit. - If you needed to use your own threaded bolt make sure you use M10 metric thread. - The cable organizer clip will help to tidy your wiring. Page 13 - Never use the Power Sting other than with the original m!ka Bushing. Table clamps are not suitable to hold an MMS arm.
  • Page 38 m!ka Remarks - Make sure that you use the correct screw size and length. Too long screws will damage your flat panel! Page 19 - You can deactivate the QuickFix function for security reasons. Turn in the screw next to the release lever in order to disengage its function. Page 20 - Insert the cable organizer clips into the bottom profile of the MMS Arm and turn it 90°...
  • Page 39 Page 25 - Never use the m!ka Table Clamp on curved surfaces - it may slip off! Page 27 - You do not need to drill a central hole when you use a m!ka Table Top Mount. - Make sure you have suitable screws for the type of panel you install the base ring to. Page 28 - When installing the m!ka Wall Bracket it is your obligation to verify that your wall and your fasteners are suitable to hold the load.
  • Page 40 yellowtec.com...

Table of Contents