Table of Contents
Advertisement
Quick Links
Fluidcontrol
Temperature sensor
TF with IO-Link
Installation and Operation Instructions
Original instructions
BE140016
Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen
09/2020
Tel. +49 (0) 21 02 / 49 89-0, Fax: +49 (0) 21 02 / 49 89-20
E-Mail: fluidcontrol@buehler-technologies.com
Internet: www.buehler-technologies.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bühler technologies TF with IO-Link
Summary of Contents for Bühler technologies TF with IO-Link
- Page 1 Fluidcontrol Temperature sensor TF with IO-Link Installation and Operation Instructions Original instructions BE140016 Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen 09/2020 Tel. +49 (0) 21 02 / 49 89-0, Fax: +49 (0) 21 02 / 49 89-20 E-Mail: fluidcontrol@buehler-technologies.com Internet: www.buehler-technologies.com...
- Page 2 Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen Tel. +49 (0) 21 02 / 49 89-0, Fax: +49 (0) 21 02 / 49 89-20 Internet: www.buehler-technologies.com E-Mail: fluidcontrol@buehler-technologies.com Read this instruction carefully prior to installation and/or use. Pay at- tention particularly to all advises and safety instructions to prevent in- juries.
-
Page 3: Table Of Contents
TF with IO-Link Contents Introduction............................................. 2 Intended Use......................................... 2 Layout and Functionality .................................... 2 Scope of Delivery........................................ 2 Model key.......................................... 2 Safety instructions......................................... 3 Important advice ......................................... 3 General hazard warnings .................................... 4 Transport and storage ........................................ 5 4 Installation and connection ...................................... 6 Installation .......................................... 6... -
Page 4: Introduction
TF with IO-Link 1 Introduction 1.1 Intended Use The TF temperature sensors are used to monitor temperatures inside a tank. The TF temperature sensors can also be used in piping and cooling matrices. In this case the tube is located inside the tank. Ac- cording to EN 60079-11, the TF series temperature sensors are simple electrical apparatuses without separate voltage source in- tended for tank top installation. -
Page 5: Safety Instructions
TF with IO-Link 2 Safety instructions 2.1 Important advice Operation of the device is only valid if: – the product is used under the conditions described in the installation- and operation instruction, the intended application according to the type plate and the intended use. In case of unauthorized modifications done by the user Bühler Technolo- gies GmbH can not be held responsible for any damage, –... -
Page 6: General Hazard Warnings
TF with IO-Link 2.2 General hazard warnings The equipment must be installed by a professional familiar with the safety requirements and risks. Be sure to observe the safety regulations and generally applicable rules of technology relevant for the installation site. Prevent malfunctions and avoid personal injuries and property damage. -
Page 7: Transport And Storage
TF with IO-Link 3 Transport and storage Only transport the product inside the original packaging or a suitable alternative. The equipment must be protected from moisture and heat when not in use. It must be stored in a covered, dry, dust-free room at room temperature. -
Page 8: Installation And Connection
TF with IO-Link 4 Installation and connection 4.1 Installation The temperature sensor comes fully assembled and can be mounted to the tank with a screw fitting and seal. Please be sure to leave enough space between the tank wall and add-ons. The maximum torque of the screw-in thread is 25 Nm. When installing, be sure the sealing face is clean and even. -
Page 9: Operation And Control
TF with IO-Link 5 Operation and control NOTICE The device must not be operated beyond its specifications. Version with IO-Link interface This unit is equipped with an IO-Link interface, which require an IO-Link master. The IO-Link interface allows direct access to process and diagnostics data, and allows configuring the unit during operation. -
Page 10: Cleaning And Maintenance
TF with IO-Link 6 Cleaning and Maintenance This device is maintenance-free. The method for cleaning the devices must be adapted to the IP protection class of the devices. Do not use cleaners which could damage the device materials. Bühler Technologies GmbH... -
Page 11: Service And Repair
TF with IO-Link 7 Service and repair This chapter contains information on troubleshooting and correction should an error occur during operation. Repairs to the unit must be performed by Bühler authorised personnel. Please contact our Service Department with any questions: Tel.: +49-(0)2102-498955 or your agent... -
Page 12: Disposal
TF with IO-Link 8 Disposal Dispose of parts so as not to endanger the health or environment. Follow the laws in the country of use for disposing of elec- tronic components and devices during disposal. Bühler Technologies GmbH BE140016 ◦ 09/2020... -
Page 13: Appendix
TF with IO-Link 9 Appendix 9.1 Technical Data TF-M-G1/2-xx-M12-TD-1D1S Dimensions TF-M-G1/2 TF-E-G1/2 M12x1 Version: Probe material: Brass 1.4571 Max. operating pressure: 5 bar 10 bar Connection: G1/2 G1/2 SW 36 Medium temperature: -20 °C to +80 °C Ambient temperature: -20 °C to +70 °C 32.3... -
Page 14: Attached Documents
TF with IO-Link 10 Attached documents – Declaration of Conformity KX110021 – IO-Link HX00002 manufacturer declaration – RMA decontamination statement Bühler Technologies GmbH BE140016 ◦ 09/2020... - Page 16 Herstellererklärung Manufacturer Declaration Die Firma Bühler Technologies GmbH erklärt in The company Bühler Technologies GmbH declares under their sole responsibility, the alleiniger Verantwortung, dass die Produkte products Produkttyp/ IO-Link Device product type: Niveau- und Temperaturschalter / Level- and temperature switch NT 67-XP, NV 77-XP, NT M-XP, NT 63-LTD, NT M-LTD Anzeige- und Steuereinheit / Display and control unit TT-77W,Multitronik, BCM-XD...
- Page 17 RMA-Formular und Erklärung über Dekontaminierung RMA-Form and explanation for decontamination RMA-Nr./ RMA-No. Die RMA-Nummer bekommen Sie von Ihrem Ansprechpartner im Vertrieb oder Service./ You may obtain the RMA number from your sales or service representative. Zu diesem Rücksendeschein gehört eine Dekontaminierungserklärung. Die gesetzlichen Vorschriften schreiben vor, dass Sie uns diese Dekontaminierungserklärung ausgefüllt und unterschrieben zurücksenden müssen.
- Page 18 Dekontaminierungserklärung DE000011 Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen 01/2019 Tel. +49 (0) 21 02 / 49 89-0, Fax: +49 (0) 21 02 / 49 89-20 E-Mail: service@buehler-technologies.com Internet: www.buehler-technologies.com...
Need help?
Do you have a question about the TF with IO-Link and is the answer not in the manual?
Questions and answers