Download Print this page
Nokia 1265 Description And Troubleshooting
Nokia 1265 Description And Troubleshooting

Nokia 1265 Description And Troubleshooting

Baseband
Hide thumbs Also See for 1265:

Advertisement

Quick Links

Nokia Customer Care
1265 (RH-103)
Mobile Terminal
Baseband Description and
Troubleshooting
Issue 1 04/2007
Company Confidential
© 2007 Nokia Corporation

Advertisement

loading

Summary of Contents for Nokia 1265

  • Page 1 Nokia Customer Care 1265 (RH-103) Mobile Terminal Baseband Description and Troubleshooting Issue 1 04/2007 Company Confidential © 2007 Nokia Corporation...
  • Page 2: Table Of Contents

    Flash Faults ....................28 Power Does Not Stay ON or the Mobile Terminal is Jammed ......29 Charger Faults .....................30 Audio Faults....................31 Display Faults ....................35 Keypad Faults ....................36 Keypad Faults ....................37 Page 2 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 3: Introduction

    MSM bus bridges support peripherals that do not have an AHB interface. The mobile terminal supports standard Nokia 2-wire and 3 wire chargers (AC-3, AC-4, DC-4). However, the 3-wire chargers are treated as 2-wire chargers. The pulse width modulation (PWM) controls signal for controlling the 3-wire charger is ignored.
  • Page 4: Baseband And Power Management Architecture

    1265 (RH-103) Baseband Description and Troubleshooting Baseband and Power Management Architecture Figure 1: Baseband Diagram Figure 2: Power Management of QSC6010 Page 4 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 5: Power Up And Reset

    20ms and is sent to MSM. Resets are generated for the MSM’s internal MCU and its internal DSP, and MSM sends TCXO_ON (“TCXO_EN” pin in 1265 schematic) signal to PM to enable TCXO. After PON_RESET_N goes high, MSM holds PS_HOLD at low state for 200ms and then drives PS_HOLD to high state.
  • Page 6: Power Up

    When the power key is pressed, the PM enters the power-up sequence. Pressing the power key causes the KPD_PWR_N (PHONE_ON_N pin in 1265 schematic) pin to GND. The KPD_PWR_N signal is not part of the keypad matrix. The power key is only connected to the PM.
  • Page 7: Power Off

    There are several sub-states under the active mode. Depending on the mobile terminal’s current state, there are states such as burst reception, burst transmission, etc. Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 7...
  • Page 8: Power Distribution

    (PURX) is not released if the battery voltage is less than 3 V. Page 8 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 9: Clock Distribution

    19.2 MHz +/-2ppm. The SLEEP_CLK provides a 32.768 kHz +/-20ppm clock source to drive the MSM controller into sleep mode. At this mode, most of the MSM is powered down and the TCXO is disabled. Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 9...
  • Page 10: System Clocks

    The PM includes several clock circuits (Figure 4), whose outputs are used for general housekeeping, MSM and RF functions within the mobile terminal system. Figure 4: TCXO & SLEEP_XTAL Block Diagram Page 10 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 11: Tcxo

    PM defaults to this SBI-controlled mode with the TCXO defaulted on. This assures the MSM will always have a clock available immediately at power-up even if TCXO_EN is low. TCXO waveform (19.2MHz +/-2ppm) Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 11...
  • Page 12: Sleep Crystal Circuit For 32.768 Khz

    SLEEP Crystal Circuit for 32.768 kHz The 32.768 kHz crystal oscillator is the primary SLEEP clock source when TCXO clocks are disabled to save power. Figure 7: Sleep CLK Block Diagram Page 12 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 13 The crystal oscillator dissipates little power, adjusting its bias current to the minimum required to maintain oscillation. SLEEP Clock waveform (32.768KHz +/-20ppm) Figure 8: Sleep_CLK Timing at 25 Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 13...
  • Page 14: Sbi Clk Interface

    This table describes the errors condition during Flash memory downloading to the mobile terminal. Description Not Working Properly Packet Checksum fail ERR: CRC invalid Erase fail Unable to erase device Write fail Write unsuccessfully Figure 10: Flash Programming Error Description Page 14 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 15: Charging Operation

    Charging Operation Battery The 1265 uses a Lithium-Ion cell battery with a capacity of 860 mAh. QSC6010 reads the resistor inside the battery pack on the BSI line to identify the battery size. Different charging algorithm will be used for different battery sizes. The resistors are connected to the BSI pin inside the battery connector.
  • Page 16: Charger Detection

    Baseband Description and Troubleshooting Charger Detection Connecting a charger creates a voltage on the VCHG (“VEXT_DC” pin in 1265 schematic) input of the PM. Charging starts when the PM detects the VCHG input voltage level above 3.3V (Min. working voltage of VCHG pin).
  • Page 17: Charge Control

    The baseband supports 2 microphone inputs and three receiver (earpiece)/ speaker outputs. MIC+ & MIC- inputs of 1265 schematic are used for the mobile terminal's internal microphone. JACK_MIC+ & JACK_MIC- input are used for headsets. Every microphone input can have either a differential or single-ended AC connection to the QSC6010 circuit.
  • Page 18: Display And Keyboard

    The mobile terminal uses a white and black LCD. The interface uses a parallel bus to transfer the Command/ Data between QSC6010 and LCD. The panel for 1265 is a 96x65dot matrix FSTN LCD module. It has a FSTN panel composed of 96 segments and 65 commons. The LCD interface uses parallel bus for controlled Command/ Data .
  • Page 19: Charging

    The mobile terminal supports Nokia standard 2.5mm mono headset. The headset insertion to the mobile terminal is detected through pin 4 (HS_DET) of the headset Jack, J580. HS_DET (“JACK_SENSE” pin in 1265 schematic) is low when headset not inserted. It becomes high when headset is inserted.
  • Page 20 1265 (RH-103) Baseband Description and Troubleshooting UIM_DATA UIM_CLK UIM_REST VREG_RUIM Figure 17: RUIM Card Serial Timing Page 20 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 21: Test Points - Top

    1265 (RH-103) Nokia Customer Care Baseband Description and Troubleshooting Test Points – Top VREG_RUIM VPH_PWR VIB_DRV_N ROM_CS_N JACK_MIC+ JACK_DET JACK_MIC- PHONE_ON_N BATT_ID WDOG_EN UART1_RXD UART1_TXD BATT_VOLT VREG_MSMP PS_HOLD Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 21...
  • Page 22 1265 (RH-103) Baseband Description and Troubleshooting VREG_MSMA VREG_RFRX PA_ON VREG_RFTX VREG_TCXO 32kHz crystal RESOUT_N PA_THERM MEM_WE_N VREG_MSMC Page 22 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 23 1265 (RH-103) Nokia Customer Care Baseband Description and Troubleshooting RF feed pad for antenna SPK_P SPK_N Ground pad for antenna Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 23...
  • Page 24: Test Points - Bottom

    1265 (RH-103) Baseband Description and Troubleshooting Test Points – Bottom LCD Module LEDs RECEIVER+ RECEIVER- LCM_RS LCM_WE_N LCM_OE_N LCM_CS_N Display connector Page 24 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 25 1265 (RH-103) Nokia Customer Care Baseband Description and Troubleshooting MIC- MIC+ Keypad LEDs Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 25...
  • Page 26: Troubleshooting

    Memory IC is underfilled and can not be replaced. • The Shielding Cover can not be reused after removal. • After using the heat gun, the domesheet needs to be replaced. Page 26 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 27: Mobile Terminal Is Dead

    1265 (RH-103) Nokia Customer Care Baseband Description and Troubleshooting Mobile Terminal is Dead Mobile Terminal is Dead ♦ If current is zero, check L208, Q209, R214 and check the power on sequence. If there is no power output, Reheat solder joints or...
  • Page 28: Flash Faults

    (TP56) and WR_N phone can not be (R453). Are they repaired and must toggling during be replaced. programming? Memory IC is defective, phone can not be repaired and must be replaced. Page 28 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 29: Power Does Not Stay On Or The Mobile Terminal Is Jammed

    1265 (RH-103) Nokia Customer Care Baseband Description and Troubleshooting Power Does Not Stay ON or the Mobile Terminal is Jammed Mobile Terminal is Jammed Measure VREG_MSMP, Check VPH_PWR, VREG_MSMP, VREG_MSMC, Repair capacitors, reheat VREG_MSMC, VREG_MSMA, VREG_MSMA, and solder joints/ change and VREG_TCXO capacitors.
  • Page 30: Charger Faults

    1265 (RH-103) Baseband Description and Troubleshooting Charger Faults Charger Faults Connect the charger and make sure the battery is connected. Check/ changeJ202, Check the “BSI” line. C225, R224. Is it about 75k Ohm or 81k Ohm? Measure voltage Check/ change DC Jack, at D205.
  • Page 31: Audio Faults

    RECEIVER+ and RECEIVER- ? receiver (earpiece). Check/ change C509, C510, Audio c545. If OK, MSM is Faults defective, phone can not be Page 2 repaired and must be replaced. Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 31...
  • Page 32 Is the signal going to the MSM at If OK, MSM is MIC1+ and MIC- at C541? defective, phone can not be repaired and must be replaced. Retest Audio Faults Page 3 Page 32 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 33 Check/ change C505,C506 , Stereo Audio/Vibra If OK, MSM is defective, Speaker Mobile terminal phone can not be repaired Speaker control Test command and must be replaced. Audio Faults Page 4 Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 33...
  • Page 34 Stereo Audio / Vibra Vibrator Control Test Command vibrator should work. Measure the Change the VIB_DRV_N QSC6010,CR405, C409 signal on the vibrator. Is the signal OK? Change the vibrator Page 34 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 35: Display Faults

    1265 (RH-103) Nokia Customer Care Baseband Description and Troubleshooting Display Faults Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 35...
  • Page 36 Check LCD supply voltage at repaired and must J410 pin6. Is it okay? be replaced Check LCD signals: LCM_CS_N(J410_pin5), LCM_OE_N(J410_pin4), Change LCD LCM_WE_N(J410_pin3), LCM_RS(J410_pin2). Are the Module signals okay? RESET Page 36 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...
  • Page 37: Keypad Faults

    Change QSC6010 Sw9 PIN2 (2.95V). key working? Is it high? Measure voltage at SW9 when power key Retest is pressed. Is it Low? Keypad Change QSC6010 Faults Page 2 Issue 1 04/2007 © 2007 Nokia Corporation Company Confidential Page 37...
  • Page 38 QSC6010 and keypad on and must be replaced. every inner dome Key. Otherwise, remove the short Are they about 0V? QSC6010 is defective, phone can not be repaired and must be replace Page 38 © 2007 Nokia Corporation Company Confidential Issue 1 04/2007...

This manual is also suitable for:

Rh-103