Related Manuals for Exmark 135-0192
Summary of Contents for Exmark 135-0192
- Page 1 135-0192 SPREADER ACCESSORY For Serial Nos. 402,082,300 & Higher Part No. 4503-424 Rev. E...
- Page 2 State of California to cause cancer, birth defects, or other reproductive harm. Exmark reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products manufactured previously.
-
Page 3: Introduction
All Exmark parts are thoroughly tested and inspected before leaving the factory, however, attention is required on your part if you are to obtain the fullest measure of satisfaction and performance. -
Page 4: Table Of Contents
Contents Introduction ............3 Safety ..............5 Safety Alert Symbol ......... 5 Safe Operating Practices ........5 Safety and Instructional Decals ....... 7 Specifications ............8 Systems ............8 Dimensions............. 8 Setup ..............9 1 Installing the Flow Control Panel....9 2 Installing the Hopper Assembly ....10 3 Installing the Cable Mount Bracket ....10 4 Installing the Control Cable......11... -
Page 5: Safety
Only use on machines approved WARNING: Indicates a potentially hazardous by Exmark. situation which, if not avoided, Could result in death • Wear appropriate clothing including safety glasses, or serious injury. - Page 6 Always have safety shields, and safety of the machine. Failure to use original guards, switches and other devices in place and in Exmark parts could cause serious injury or proper working condition. death. Making unauthorized changes to the •...
-
Page 7: Safety And Instructional Decals
Exmark equipment dealer or labels. distributor or from Exmark Mfg. Co. Inc. • Replace all worn, damaged, or missing safety • Safety signs may be affixed by peeling off the signs. -
Page 8: Specifications
Specifications Specifications Systems Spreader System • Maximum Hopper Capacity: 80 lb (36 kg) • Spreader Motor: 12VDC variable speed gear motor • Spreader Width: Adjustable from 4ft (1.2 m) up to 22 ft (6.7 m). Dimensions Overall Width: 27 inches (69 cm) Overall Length: 32 inches (81 cm) Overall Height:... -
Page 9: Setup
Setup Setup Loose Parts Use the chart below to verify that all parts have been shipped. Dealer Pack Part No. Description Qty. 323-7 Screw-HH 3/8-16 x 1 1/4 [Aer30] 104-7201 Nut-Nyloc 1/4-20 Flg [Aer30] 321-3 Installing the Flow Control Panel Screw-HH 1/4-20 x 5/8 [Aer30] 3234-47 Screw-HH FLG 5/16-18 x 3/4 [Aer24]... -
Page 10: Installing The Hopper Assembly
Setup Installing the Hopper Assembly Parts needed for this procedure: Procedure Insert the hopper hitch tube into the receiver on the aerator. g213510 Figure 4 1. Hopper hitch tube 3. Cotter pin g239068 2. Hitch pin Figure 3 Outer cover hidden for clarity Use the hitch pin and cotter pin to secure the 1. -
Page 11: Installing The Control Cable
Setup g213563 Figure 5 1. Aerator 30 side bracket 5. 5/16-18 x 1 inch carriage bolt 2. 1/4-20 x 5/8 inch hex 6. Reuse nut screw g221603 Figure 6 3. 1/4 inch flanged nyloc 7. 1/4-20 x 1 inch carriage bolt 1. -
Page 12: Installing The Harness
Setup Loosen the nuts on each side of the control cable and slide into the notch of the hopper bracket. Tighten the nuts on each side of the bracket. Move the flow control lever forward and rearward making sure the gate arm is opening and fully closing. -
Page 13: Installing The Cover
Setup g253773 Figure 10 1. Secure to frame Installing the Cover g213882 Parts needed for this procedure: Figure 9 1. Spreader harness Procedure 2. Accessory plug 3. Battery Attach the cover to the hopper, in two places, by 4. Positive battery terminal inserting 1/4–20 x 3/4 inch machine hex screw and washer through the cover tab grommet and 5. -
Page 14: Product Overview
Product Overview Product Overview g212987 g221638 Figure 12 Figure 11 1. Controls 2. Hopper 1. Cover 3. 1/4-20 x 3/4 inch machine hex screw 2. Washer 4. 1/4 inch flanged nut Secure with 1/4 inch flanged nyloc nut. Plug the other two holes in the hopper with remaining hardware. -
Page 15: Operation
Operation Operation Impeller Speed Display Located below the impeller speed control. Note: Determine the left and right sides of the This display shows the speed setting number from machine from the normal operating position. 1–10 (1 is the slowest speed and 10 is the fastest). A Important: The intended use of this spreader circle will display when the control has been turned attachment is for dispersing grass seed. -
Page 16: Pre-Start
Operation Operating Instructions CAUTION Machine can spin very rapidly by positioning one lever too much ahead of the other. Operator may lose control of the machine, which may cause damage to the machine or injury. • Use caution when making turns. •... - Page 17 Operation Determine a course length by dividing 1,000 Grass Seed Application at Maximum Ground Speed (93 m ) by the effective spread width. (Coverage 1,000 ft (93 m Type Gate Spread lb/1,000 ft For example, if the effective width is 6 feet (93 m Opening Width...
- Page 18 Operation Spreading Spreading Tips: • To ensure uniform application, be sure to overlap the grass seed distribution. The highest amount of seed will dispense from the front of the hopper and less from each side. Adjust the distribution pattern to achieve desired results.
- Page 19 Operation g207728 Figure 18 1. Effective spreading width—variable 4–22 ft (1.2–6.7 m) Evaluate the spread pattern. If adjustments are needed see the Spreader Pattern Adjustment section. When finished spreading, close the hopper gate.
-
Page 20: Operating Tips
Operation Spreader Pattern Adjustment • to the left side, slightly pull the control handle rearward. If the spread pattern is skewed or dispensing too • to the right side, slightly push the control light/heavy to one side (see Figure 19 ), adjust the handle forward. -
Page 21: Maintenance
Maintenance Maintenance Note: Determine the left and right sides of the machine from the normal operating position. WARNING While maintenance or adjustments are being made, someone could start the engine. Accidental starting of the engine could seriously injure you or other bystanders. Remove the key from the ignition switch, engage parking brake, and pull the wire(s) off the spark plug(s) before you do any maintenance to the... -
Page 22: Adjusting The Gate Closure
Maintenance Cleaning Clean Debris From Machine Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake. Clean off any debris or build-up on the machine, especially the impeller. g027205 Figure 21 1. -
Page 23: Troubleshooting
Troubleshooting Troubleshooting The following table lists some of the common causes of trouble. If a problem continues, contact an Authorized Service Dealer. Problem Possible Cause Corrective Action Message displays “STALLED (02)” 1. Controller has detected an excessive 1. Check impeller and hopper for electrical current to the impeller motor. -
Page 24: Schematics
Schematics Schematics Electrical Schematic g212875... - Page 25 Notes:...
- Page 26 Notes:...
- Page 27 Service Record Date: Description of Work Done: Service Done By:...
- Page 28 Place Model No. and Serial No. Date Purchased Label Here (Included in the Literature Pack) or Fill in Below Model No. Serial No. ©2018 Exmark Mfg. Co., Inc. Part No. 4503-424 Rev. E Industrial Park Box 808 (402) 223-6375 Beatrice, NE 68310 Fax (402) 223-5489...