Woods RB72.50 Operator's Manual
  1. Manuals
  2. Brands
  3. Woods Manuals
  4. Construction Equipment
  5. RB72.50
  6. Operator's manual

Woods RB72.50 Operator's Manual

Rear blades
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
REAR BLADES
RB72.50, RB84.50, RB96.50
RB84.60, RB96.60

Advertisement

Table of Contents
loading

Related Manuals for Woods RB72.50

Summary of Contents for Woods RB72.50

  • Page 1 REAR BLADES RB72.50, RB84.50, RB96.50 RB84.60, RB96.60...

  • Page 2: Introduction

    TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ..........2 SPECIFICATIONS.

  • Page 4: Specifications

    SPECIFICATIONS RB72.50 RB84.50 RB96.50 RB84.60 RB96.60 Cutting Width 71" 83" 95" 83" 95" Moldboard Height 17" 17" 17" 17-1/2" 17-1/2" Moldboard Thickness 1/4" 1/4" 1/4" 5/16" 5/16" Overall Height 41-1/4" 41-1/4" 41-1/4" 40" 40" Overall Depth 50" 50" 50" 55"...

  • Page 5: Safety Rules

    SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! TACT A PHYSICIAN IMMEDIAT ELY IF FL UID Safety is a primary concern in the design and ENTERS SKIN OR EYES. DO NOT DELAY. manufacture of our products. Unfortunately, our  Never allow children or untrained persons to efforts to provide safe equipment can be wiped operate equipment.
  • Page 6 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!  Do not stop, start, or change directions sud- (Safety Rules continued from previous page)  Power unit must be equipped with ROPS or denly on slopes. ROPS cab and seat belt. Keep seat belt securely ...
  • Page 7  Make sure attachment is properly secured, (Safety Rules continued from previous page) adjusted, and in good operating condition. MAINTENANCE  Never perform service or maintenance with  Before dismounting power unit or performing engine running. any service or maintenance, follow these steps: ...

  • Page 8: Safety Decals

    SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 2 - 1002941 3 - 1004250 7 - 1002940 Yellow Reflector (Front) 8 - 57123 Red Reflector (Rear) 1 - Serial Number Plate 6 - 1003193 8 Safety MAN1170 (6/1/2016)
  • Page 9 Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

  • Page 10: Operation

    OPERATION The operator is responsible for the safe operation of this equipment. Operators must be instructed in and be CAUTION capable of the safe operation of the equipment, its attachments and all controls. Do not allow anyone to operate this equipment without proper instructions. ...
  • Page 11 RB 50 & 60 Series - Category 1 Hitch Bushing Kit 1043173 when using a quick hitch coupler. (See Figure 1) 1. Remove lower hitch pins (1), and Cat 2 bushings 1. Place tractor 3-point lower lift arms between inner (3) from Rear Blade frame.
  • Page 12 • Never stand in positions where you could become entrapped during adjustment changes or if the 3-point hitch suddenly lowers. • The moldboard may be inadvertently removed at a n y t im e w h il e t h e r et a in i n g b o lt s a r e removed.
  • Page 13 Angle Adjustment - Hydraulic RB50 & 60 to any position in between, right or left from center, by hydraulic remote control from the tractor seat. To pre- Series (Optional) vent damage to the Blade and hydraulic cylinder make sure lock pin (1) is removed. (See Figure 5) 1.
  • Page 14 DP11 DP11 1. Bolt 1. Ratchet jack 2. Nut 2. Offset cylinder 3. Moldboard Figure 7. RB 60 Series Offset Adjustment 4. Blade frame Figure 6. RB 50 Series Offset Moldboard Offset Adjustment - Hydraulic RB 60 Series Offset Adjustment - Mechanical RB 60 Series (See Figure 7) (See Figure 7)
  • Page 15 1. Ratchet jack 2. Tilt cylinder 1. Lock pin 2. Safety clip 3. Tilt position DP11 Figure 8. RB 50 Series Tilt Adjustment Tilt Adjustment - Mechanical RB 60 Series (See Figure 9) The RB 60 Series Rear Blades may be tilted up to 23 Figure 9.

  • Page 16: Optional Equipment

    OPTIONAL EQUIPMENT RB 50 SERIES HYDRAULIC ANGLE KIT 5. Attach relief valve (10) to holes in Rear blade frame (11) with provided cap screws (12) and lock 1043128 nuts (13). (See Figure 10) 6. Attach hoses (14 & 15) to relief valve then elbows as shown.
  • Page 17 8. Klik pin RB 50 & 60 SERIES SKID SHOE KIT 18300 Figure 12. RB 50 & 60 Series Skid Shoe Installation & RB72.50 SKID SHOE KIT 601730 (See Figure 12) RB 60 SERIES TAIL WHEEL KIT 1043145 1. Remove plow bolts and lock nuts from each end of cutting edge.
  • Page 18 1. Tail wheel mount 2. Rear blade boom 3. Carriage bolt 4. Lock nut 5. Tail wheel boom 6. Pin 7. Klik pin 8. Wheel & yoke assembly 9. Washer 10. Lock pin 11. Ratchet jack Figure 13. RB 60 Series Tail Wheel Installation Assemble Floating Link 1.

  • Page 19: Assembly Instructions

    DEALER SET-UP INSTRUCTIONS CAUTION Assembly of this Rear Blade is the responsibility of the WOODS dealer. The 50 Series Rear Blades are  Always wear relatively tight and belted clothing shipped fully assembled. The 60 Series Rear Blades to avoid entanglement in moving parts. Wear...
  • Page 20 RB 60 SERIES MECHANICAL ASSEMBLY 3. Adjust ratchet jack if necessary so that offset adjustment is centered. Angle Adjustment Tilt Adjustment RB 60 Series Rear Blades are shipped with lock pin (See Figure 15) installed for mechanical angle adjustment. No assem- bly is required.
  • Page 21 RB 60 SERIES HYDRAULIC ASSEMBLY 5. Attach relief valve (9) to bracket on boom (10) with short cap screws (11) and lock nuts (12). Angle Adjustment 6. Attach hoses (13 & 14) to relief valve, route through hose loop, then attach elbows as shown. (See Figure 16) 7.
  • Page 22 Offset Adjustment 6. Attach fittings (12) to relief valve, then hoses (13) to fittings. (See Figure 17) 7. Route hoses through loop on A-Frame and install 1. Remove shipping bracket (1) and hardware quick disconnect fittings (14) to hoses. between hitch (2) and boom (3). NOTE: Replace short cap screws with long cap 2.
  • Page 23 Tilt Adjustment 4. Attach hoses (6) to elbows and route hoses through hose loops. (See Figure 18) 5. Secure hoses with clamps (7), cap screws (8), and 1. Remove shipping bracket (1) and hardware lock nuts (9) to relief valve bracket, or relief valve if between moldboard (2) and pivot (3).

  • Page 24: Owner Service 24

    ● Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of  Always wear relatively tight and belted clothing matching color (Purchase from your Woods to avoid getting caught in moving parts. Wear dealer).

  • Page 25: Dealer Check Lists

    DEALER CHECK LISTS PRE-DELIVERY CHECK LIST wheels. When adding weight to attain 20% of tractor and equipment weight on front tractor Inspect the equipment thoroughly after assembly to be wheels, you must not exceed the ROPS weight certain it is set up properly before delivering it to the certification.
  • Page 26 NOTES Dealer Check Lists 26 MAN1170 (6/1/2016)

  • Page 27: Parts

    RB84.60, RB96.60 RB72.50, RB84.50, RB96.50 ASSEMBLY ....28 - 29 RB84.60, RB96.60 ASSEMBLY......30 - 31 HYDRAULIC ANGLE KIT 1043128 FOR 50 SERIES .
  • Page 28 RB72.50, RB84.50, RB96.50 REAR BLADES 28 Parts MAN1170 (6/1/2016)
  • Page 29 RB72.50, RB84.50, RB96.50 REAR BLADES RB72.50 RB84.50 RB96.50 DESCRIPTION 1042710 1042710 1042710 Hitch frame 1042711 1042711 1042711 Pivot frame 1042712 1042712 1042712 Offset frame 104271372 104271384 104271396 Moldboard 25258 25263 25270 Cutting edge 26920 (6) 26920 (8) 26920 (8) 5/8 NC x 1-3/4 Plow bolt...
  • Page 30 RB84.60, RB96.60 REAR BLADES 30 Parts MAN1170 (6/1/2016)
  • Page 31 RB84.60, RB96.60 REAR BLADES RB84.60 RB96.60 DESCRIPTION 1042721 1042721 Hitch frame 1042722 1042722 Boom frame 1042723 1042723 Pivot frame 104272484 104272496 Moldboard 25263 25270 Cutting edge 26920 26920 5/8 NC x 1-3/4 Plow bolt 6239 6239 5/8 NC Hex lock nut 1042716 1042716 Washer, non-hydraulic...
  • Page 32 RB72.50, RB84.50, RB96.50 HYDRAULIC ANGLE KIT 1043128 (OPTIONAL) PART DESCRIPTION PART DESCRIPTION 3/4 SAEM x3/4 JICM Adapter 1043130 3 x 10 Hydraulic cylinder 1020204 1/2 NPTM x 3/4 JICM Elbow PART DESCRIPTION 1042717 Hydraulic angle plate 37964 * 5/16 NC x 3 HHCS, GR5 37653 1.0 x 1.50 x .75 Sleeve...
  • Page 33 PART DESCRIPTION HHCS Hex Head Cap Screw * Standard Hardware, Obtain Locally RB84.60, RB96.60 HYDRAULIC ANGLE KIT 1043125 (OPTIONAL) PART DESCRIPTION PART DESCRIPTION 1043131 3 x 12 Hydraulic cylinder 1020204 1/2 NPTM x 3/4 JICM Elbow 1043161 Hydraulic angle plate 37653 1.0 x 1.50 x .75 Sleeve PART...
  • Page 34 RB84.60, RB96.60 HYDRAULIC OFFSET KIT 1043126 (OPTIONAL) PART DESCRIPTION PART DESCRIPTION 1043129 3 x 8 ASE Hydraulic cylinder 3/4 SAEM x 3/4 JICM Adapter 1020204 1/2 NPTM x 3/4 JICM Elbow 1004282 Hose, 54" x 1/2 NPT x 3/4 JICF 360174 Hose, 36"...
  • Page 35 RB84.60, RB96.60 HYDRAULIC TILT KIT 1043127 (OPTIONAL) PART DESCRIPTION 1043129 3 x 8 ASE Hydraulic cylinder 1020204 1/2 NPTM x 3/4 JICM Elbow Hose clamp 14562 * 5/16 NC x 1 HHCS, GR5 14139 * 5/16 NC Flanged lock nut 1004856 Hose, 108"...
  • Page 36 RB84.60, RB96.60 SELECTOR VALVE KIT 1043134 (OPTIONAL) PART DESCRIPTION 1043156 Selector valve bracket 1004261 Selector valve 316017 1-1/6 SAEM x 3/4 JICM adapter 1004281 Hose, 26" x 3/4 JICF x 3/4 JICF 37501 1/16 JICM x 3/4 JICM Elbow 976 * 3/8 NC x 1-1/2 HHCS, GR5 7747 * 3/8 NC x 3 HHCS, GR5...
  • Page 37 5/8 NC x 1-1/2 Carriage bolt, GR5 6239 6239 * 5/8 NC Hex lock nut * Standard Hardware, Obtain Locally SKID SHOE KIT 18300 & 601730 (OPTIONAL) RB84.50 RB96.50 RB72.50 DESCRIPTION RBXX.60 18300 601730 Skid shoe kit 27586 27586 Skid shoe...
  • Page 38 TAILWHEEL KIT 1043145 (OPTIONAL) 38 Parts MAN1170 (6/1/2016)
  • Page 39 TAILWHEEL KIT 1043145 (OPTIONAL) PART DESCRIPTION PART DESCRIPTION 1043145 Tailwheel kit 1030520 Tail wheel assembly 1043167 Tailwheel mount 1030521 Wheel & hub assembly 1043168 Tailwheel boom 1030522 Hub assembly HBL233 7/8 Hitch pin 1030524 Bushing 43627 * Klik pin 300300 * 1/2 NC x 1 HHCS, GR5 20020705 Ratchet jack...

  • Page 40: Bolt Torque Chart

    BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.

  • Page 41: Bolt Size Chart & Abbreviations

    BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG...............Agriculture MPa ............Mega Pascal ASABE ....American Society of Agricultural & N ..............

  • Page 42: Product Warranty

    The limited warranty covers any defects in the material and/or workmanship. Following the proper, recommended installation by an authorized Woods Dealer and normal use of a Woods mounting and backhoe or loader, if a tractor incurs damage resulting from the attachment, Woods will cover the existing tractor warranty in the event the manufacturer voids its tractor warranty because of the attachment.
  • Page 43 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.
  • Page 44 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec- tive companies or mark holders. Specifications subject to change without notice.

This manual is also suitable for:

Rb84.50Rb96.50Rb84.60Rb96.60

Table of Contents