Related Manuals for Orbinox RB
Summary of Contents for Orbinox RB
- Page 1 INSTALLATION, OPERATION AND MAINTENANCE MANUAL MODEL WEIR GATE SPAIN · UK · GERMANY · FRANCE · CANADA · USA · BRAZIL · CHILE · PERU · INDIA · CHINA · SOUTH EAST ASIA www.orbinox.com...
-
Page 2: Table Of Contents
• This manual describes the recommended procedures for installation, operation, maintenance and safety precautions for ORBINOX RB model weir gates • Please read thoroughly all the instructions in the manual prior to installation and contact an ORBINOX representative in case of any questions •... -
Page 3: Equipment Main Components
2. EQUIPMENT MAIN COMPONENTS ITEM DESCRIPTION FRAME FRAME INVERT FRAME GUIDE SLIDE YOKE EPDM SEAL (U)HMWPE GUIDE THREADED STEM BEVEL GEAR HANDWHEEL ACTUATOR (OTHER ACTUATORS AVAILABLE) STEM PROTECTOR Reserves the right to change specifications without notice EDITION 10-2020 www.orbinox.com RB-3/12... -
Page 4: Installation
▶ Required Materials: • ORBINOX RB Weir Gates are installed by means of Anchor Bolts. Depending on the size and working conditions they shall be either of the mechanical or chemical type. In order to get the expected performance of the anchor bolts, the minimum concrete strength shall be 25 MPa (3,625 PSI) •... - Page 5 • Apply construction sealant around the frame in order to fill in any existing gap between the wall and the frame (this step is only for esthetics). Wipe away the excess sealant to leave a smooth finish. Reserves the right to change specifications without notice EDITION 10-2020 www.orbinox.com RB-5/12...
-
Page 6: Installation: Stem Extension, Stem Guides And Floor Stand (When Applicable)
Figure 3 3.2. Installation: stem extension, stem guides and floor stand (when applicable) • Some RB weir gates include stem extensions, extension guides and floor stand (depending on the configuration of the civil works) • Once the gate is installed, the rest of the elements must be installed: o Connect the stem extension (item 3) to the shaft (item 1) on top of the yoke o Insert all stem guides from the top of the stem extension (when applicable). - Page 7 MODEL WEIR GATES Adjust Stem Extension Aligment Operator Floor Stand Stem Guide Adjust offset Connect the distance Extension to the from wall Slide Gate Figure 4 Reserves the right to change specifications without notice EDITION 10-2020 www.orbinox.com RB-7/12...
-
Page 8: Operation
• The RB weir gate is closed by a clockwise rotation, and opened (downwards) by a counter-clockwise rotation of the operator • The RB weir gate is designed to be self-locking, so that the slide maintains its position in open, close or intermediate positions... -
Page 9: Maintenance
Spare parts: ORBINOX does not recommend stocking any spare parts by the owner of the equipment as the weir gates are designed for a very long life cycle. If a repair part is required, please contact an ORBINOX representative and provide the following information: •... -
Page 10: Vertical And Bottom Seals Replacement
• Remove seal (item 12) and replace it by the new seal. After installing the new seal, apply grease on it to ease operation NOTE: the shaft must be completely empty to carry out this maintenance operation as the seals are bolted to the frame Figure 5 Reserves the right to change specifications without notice EDITION 10-2020 www.orbinox.com RB-10/12... - Page 11 • Remove the seal retainer (items 7 and 8) • Remove seal (item 9) and replace it by the new seal. After installing the new seal, apply grease on it to ease operation. Figure 6 Reserves the right to change specifications without notice EDITION 10-2020 www.orbinox.com RB-11/12...
-
Page 12: Trouble Shooting
• Please follow the local environmental rules in your country for proper disposal Reserves the right to change specifications without notice EDITION 10-2020 www.orbinox.com RB-12/12...