Advertisement
Owner's Manual
WAPLS Series
Thermoplastic
Sprinkler Pumps
WA10/15PLS
WA20PLS
TABLE OF CONTENTS
General Safety . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . .3-5
Electrical . . . . . . . . . . . . . . . . . . . . . . . .6
Operation . . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting . . . . . . . . . . . . . . . . . . 8
Repair Parts . . . . . . . . . . . . . . . . . . . . . 9
Warranty . . . . . . . . . . . . . . . . . . . . . . . 10
Advertisement
Table of Contents
Related Manuals for Water Ace WAPLS Series
Summary of Contents for Water Ace WAPLS Series
-
Page 1: Table Of Contents
Owner’s Manual WAPLS Series Thermoplastic Sprinkler Pumps WA10/15PLS WA20PLS TABLE OF CONTENTS General Safety ....2 Installation .....3-5 Electrical . -
Page 2: General Safety
Before you start STOP Fill Pump with water to prime: Ensure pump body is filled with water to discharge. Motor’s Electrical Settings: Set motor to proper voltage. Help Line: Call 1-844-394-2604 for assistance Important Safety Instructions Carefully read and follow all safety instructions in this manual and on pump. SAVE THESE INSTRUCTIONS –... -
Page 3: Installation
INSTALLATION Cased Well/Dug Well Installation Before You Install Your Pump 1. Inspect foot or in line check valve to be sure it NOTICE works freely. Inspect strainer to be sure it is clean 1. The pump’s water suction inlet must not be move than 20’... - Page 4 INSTALLATION Driven Point Installation-Figure 2 Discharge pipe Gate valve 1. Connect suction pipe to drive point (Fig. 2). Keep horizontal pipe run as short as possible. To sprinkler heads Use Teflon tape on male pipe threads. Multiple well points may be necessary to provide sufficient water to pump.
- Page 5 INSTALLATION Pipe from Well to Pump Pump/Piping Installation 1. Pump performance will be decreased if the pipe If turning pump on and off by pressure, a pressure diameter is less than the inlet size of the pump. In switch and tank are required. For proper installation, proper installation, the pipe size equals the inlet size.
-
Page 6: Electrical
ELECTRICAL Disconnect power before working on pump, motor, pressure switch or wiring Motor may be hot. Allow to cool 20 minutes. Water pressure may have built up in the pump, pipes and/or tank. Drain water to relieve pressure. Motor Voltage Settings Motors are designed to run on either 115 volt or 230 volt current. -
Page 7: Operation
OPERATION Hazardous Pressure, Install pressure relief valve in discharge pipe. Release all pressure on system before working on any component. Priming the Pump Risk of explosion and scalding. NOTICE ‘Priming’ refers to pump expelling all air in the NEVER run pump against closed discharge. To do so system and beginning to move water from its source out can boil water inside pump, causing hazardous pressure into system. -
Page 8: Troubleshooting
WA10PLS WA15PLS WA20PLS... -
Page 9: Repair Parts
REPAIR PARTS EFLS10P/15P 1 HP and 1-1/2 HP Part Quantity Part Number Description EFLS10001 O-RING EFLS10002 O-RING EFLS20P 2 HP Part Quantity Part Number Description EFLS20001 O-RING EFLS20002 O-RING... -
Page 10: Warranty
WARRANTY Retain Original Purchase Receipt for Warranty Eligibility Limited Warranty Manufacturer warrants to the original consumer purchaser (“Purchaser” or “You”) that its products are free from defects in material and workmanship for a period of twelve (12) months from the date of the original consumer purchase. If, within twelve (12) months from the original consumer purchase, any such product shall prove to be defective, it shall be repaired or replaced at manufacturer’s option, subject to the terms and conditions set forth herein.
Need help?
Do you have a question about the WAPLS Series and is the answer not in the manual?
Questions and answers