Taymor 06-8724S Installation Instructions

INSTALLATION INSTRUCTIONS
06-8724S / 06-8724SSS
SINGLE HANDLE KITCHEN FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable
Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply
valves. These are usually found under the sink.
FAUCET INSTALLATION
3
1) OPTIONAL ESCUTCHEON INSTALLATION: Remove old faucet. Clean sink surface in
preparation for new faucet. Apply a bead of plumber's putty or silicone caulk around the
faucet openings. Install the gasket over the three holes in your sink.
2) OPTIONAL ESCUTCHEON INSTALLATION: Screw bolts (1) to the escutcheon (2). Install
escutcheon over the three holes in the sink. From underneath sink, hand tighten mounting
nut. Do not overtighten.
3a) OPTIONAL INSTALLATION ESCUTCHEON: Retract pull-down hose (1) up through faucet
body, until the pull-down hose fitting is flush with the bottom of shank (2). Do not pull hose
fitting past the shank. Insert faucet body through the hole in escutcheon. Note: Do not feed
the pull-down hose (1) back down through the spout until step 3.
3b) OPTIONAL INSTALLATION WITHOUT ESCUTCHEON: Retract pull-down hose (1) up
through faucet body, until the pull-down hose fitting is flush with the bottom of shank (2).
Do not pull hose fitting past the shank. Insert faucet body through the hole. Note: Do not
feed the pull-down hose (1) back down through the spout until step 3.
4) Install rubber washer (1), metal washer (2) onto the threaded mounting shank.Lock nut (3)
into position by tightening screws (4). Do not overtighten.
5) Screw quick connector (2) to the free end of pull-out hose (1).
6) Align block (1) and tabs on quick connect. Push quick connect housing firmly upward and
snap onto receiving block. Pull down moderately to ensure connection has been made. If
it is necessary to remove quick connect, squeeze tabs on hose between index finger and
thumb, then pull down to disconnect. After connecting the hose, install the weights (2) at
the lowest point of the hose.
Do not, use plumber' putty on cultured marble or other
composite sinks. Putty will discolor the sink.
1 2
3b 4
2
1
6
1
2
WITH OPTIONAL ESCUTCHEON
Your installation may require new supply
lines. (Supply lines are not included.)
Safety goggles
Torque wrench Plumber's putty
TURN OFF
3a
2
1
2
1
5
2
1
1
2
3
4
ATTACH THE HOT AND COLD SUPPLY LINES
4
Thread the nut (1) on supply line onto outlet of water supply valve (2) and tighten with
wrench. Do not overtighten.
2
Silicone caulk
FLUSHING THE WATER LINES
5
Turn on hot and cold water supplies. Pull the hose assembly out of the spout and remove
the spray head by unscrewing it from the hose counterclockwise. Be sure to hold the end
of the hose down into the sink and turn the faucet on to the warm position where it mixes
hot and cold water. Flush water lines for one minute. Check for leaks. Re-tighten any
connections if necessary, but do not overtighten. Reinstall spray head by hand tightening
it back onto the spray hose.
TURN OFF
EXPLODED DIAGRAM FOR REFERENCE
6
MAINTENANCE Your new faucet is designed for years of trouble-free performance. Keep
it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel
wool and harsh chemicals as these will dull the finish and void your warranty.
1 - INVERTER
2 - HOSE
3 - SPRAY HEAD
5 - BASE PLATE
6 - BOLT
7 - MOUNTING NUT
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
1
26 - SPOUT
25 - WASHER
24 - CLIP
23 - O-RING
22 - CARTRIDGE
21 - BONNET
4 - ESCUTCHEON
20 - CAP
16 - WASHER
14 - NUT
13 - LOCKING SCREW
12 - BLOCK
11- O-RING
10 - WEIGHT
8 - O-RING
9 - QUICK CONNECT
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
19 - CONNECT
18 - HANDLE
17 - SET SCREW
15 - METAL WASHER