Page 1
Wi-Fi IP CAMERA QUICK OPERATION GUIDE Apply for Model: BC5 /P1-4X /P3-4X/ P2-20X Note: Due to the continuous updating of the product and software, there may be a discrepancy between the operating guide and the APP interface. All the instructions are subject to the actual operation...
1. Introduction Thanks for buying YoLuke Wi-Fi IP Camera. We provide 4 different cameras which has different appearance and function. We follow the people-oriented design philosophy, these four cameras will be easily able to integrate into our daily lives, both in terms of appearance and function. This manual describes all the parameters, functional structure, how to use, common problems and solutions for the camera in detail.
4.1 Connect Wi-Fi Camera by Camera’s Wi-Fi Hotspot Connect camera with power supply Power on Wi-Fi Camera by Power adapter 12V1A(BC5) / 12V2A(P1-4X) / 12V3A(P2-20X), camera will turn into the self-test mode. It will take about 15 seconds. 4.1.1 Connect Wi-Fi (Hot Spot) Your cell phone’s Wi-Fi Setting -- search Wi-Fi signals -- connect the Wi-Fi.
4.1.2 Add camera to CamHipro A) Open App CamHipro -- Click Add device -- Web video camera B) New device -- Yes.I want to add this device -- Add to...
Page 11
C) Not configured yet, add directly -- Confirm skip-- Set up a name -- Confirm D) Click the camera that has been added to the device list to preview the real-time monitoring screen. Online means you added the camera successfully...
4.1.3 Connect the camera to Wi-Fi A) Click go to Setting page -- Wirless setting -- Get the wireless network around the device-- Select your Router’s Wi-Fi and enter the password. Wait 20-30 seconds, Wi-Fi connection success. B) Back to Camera device list, camera displayed online. Click camera for real-time preview. C) NOTE: ①.Setup Wi-Fi should restart App.
4.2 Connect the Camera by Scan QR Code A) Power on Wi-Fi Camera by Power adapter 12V1A(BC5) / 12V2A(P1-4X) / 12V3A(P2-20X) and camera will turn into the self-test mode. It will take about 15 seconds. Please make sure that the camera has connected to your router’s Wi-Fi.
4.3 Connect the Camera by Search Nearby Devices ①Power on the Wi-Fi Camera by Power adapter Guidance can be found in ②Please make sure that the camera has been connected to router’s Wi-Fi. ( 4.1.4) ③Please make sure that your cell phone connects the same Wi-Fi as the camera connected. B) Device in use -- Search nearby devices -- Click the device in the device List -- Confirm add If there is no camera on the device list, please come close to the camera and refresh.
4.4 APP Function Introduction 4.4.1 APP login display interface introduction 4.4.1.1 Video playback Click on this page, you can playback your video here. There are two ways to playback your video -- choose Time playback or File playback.
4.4.1.2 Video and image download Click to playback and download your video and images. 4.4.1.3 Local files, device list and add other new camera Click to view the local file of different cameras.;click to change the camera device list;click to add a new camera.
4.4.1.4 Pre-set point and auto cruise(for PTZ) Click the camera into real-time monitor -- turn to next page -- preset position Number 1-16 means 16 points you want to set up Adjust the camera rotation to the first point you want to monitor on the app; input "1" and Setting; Adjust the camera rotation to the second point you want to monitor on the app;...
4.4.2 APP Setting Function Click go to camera set up page. 4.4.2.1 Wireless setting Click “wireless setting” to connect the camera to your router Wi-Fi or change a Wi-Fi for the camera. 4.4.2.2 Change password Click “Change Password” to modify the password. Old password :01234567...
4.4.2.3 Alarm management and notification 4.4.2.3.1 Advanced setting You can set up the time you want to alarm. If you don’t set up a specific time, it will alarm all day. Advance setting-- choose one day-- set up the Start alarm time and End alarm time -- Add to 4.4.2.3.1 Detected area and sensitivity Adjust motion detection-- drag to draw the area of screen--adjust the sensitivity--application...
Page 20
4.4.2.3.2 Email setting Open Alarm capture sent to email --Configure Email -- write down all the information it needed-- application 4.4.2.3.3 FTP setting Open alarm capture saved to FTP--Configure FTP-- write down the information it needed --open passive mode --application after successfully test.
4.4.2.4 Video setting and audio setting Video settings: You can choose video format and adjust parameters of first stream and second stream, including code rate, frame rate and video coding level. Audio settings: You can select linear input or microphone input. Volume of input and output can be adjusted here.
4.4.2.6 SD card setting Camera comes with SD card slot, max support 128GB SD card for storage.You can view the total size and free size and you can format SD card.(Please format SD card when you first to use this SD card) 4.4.2.7 Device time setting You can set up the time of camera here -- Synchronize phone time to device or choose the time zone.
4.4.2.8 Default setting You can Reboot camera, Reset camera back to factory(you can reset camera by reset key in tail line, but not included bullet camera). 4.4.2.9 Device information View the Device ID, Device type, Software version, IP address and other device information.
5.1 Download Search Tool Download Software from the below link or Mini CD in the package, Open the file and install search tool in your computer. ( https://yoluke-tech.com --- Left Side: Software of Security Camera -- HiP2P ) 5.2 Search IP Camera...
5.3 View Video by Browser Support IE, Google and Firefox browser, Install ActiveX before view video. 5.4 Preview Interface...
Page 26
Region A Multiple preview modes. View memory card capacity and date. Click on the capture and take the current image. Local manual recording. Region B Video Recording playback: Click the playback, select the date and time, select the local playback or SD card playback, search the video files and double click on the file to play.
5.5 Parameter Settings 5.5.1 SettingMedia A) Video: Set the video format, video coding, resolution, bit rate, max frame rate, key frame interval, bit rate control and image quality. B) OSD Set: Set time stamp, time show, camera name and name show in this interface.
Page 28
C) Image: Adjust the brightness, saturation, contrast, exposure parameter and set the WDR, Aemode, Imgmode, Intelligent night mode, IR LED Control, IRCut in this interface. (The camera does not support full colour night vision and smart night vision currently.) D) Audio: audio type support G711 / 726 protocol, audio stream selection on/off, audio input type selection, input / output volume adjustment...
5.5.2 SettingNetwork A) Network: The IP address can be selected manually settings or automatically obtain. The DNS also can be selected manually or automatically. B) Wireless: Enable Wireless to search and select the wireless network that you want to add, put password.
Page 30
C) DDNS: To set up DDNS (Remote access), It is requesting an dynamic domain name to fill in the username and password which provided by Service provider. To contact us to get the camera ID number, each camera username and password will be different. Also you could use a third-party domain name to set it up.
F) P2P: Enable this function, can watch video in Mobile App via add UID Number. 5.5.3 SettingAlarm A) Audio alarm: Enable this function. Need to connect a buzzer, turn on & adjust the volume, audio alarm can work well.
Page 32
B) Motion detection: There are 4 windows selections under Motion Detection. Select different windows to display different window positions. Drag the selected window to enlarge the window proportion. Manually type the sensitivity value or swipe the sensitivity bar to adjust the sensitivity. C) Alarm: Email setting method is the same as Phone APP.
5.5.4 Setting Advanced A) User: For Change password. B) Auto snap: Time capture, Choose to set the SD card snap interval or FTP snap interval and save route. C) Timed record: Set the Record files duration, whether to open Record and stream.
Page 35
F) Terminal: Set the cruise laps, select the centred while self-check on/off, close the alarm PTZ movement on/off and indicator display mode. G) 485Set: These 3 Models BC5 / P1-4X / P2-20X can’t support RS485. H) Multiple setting: In the same LAN, two or more of this series products from our company's, can be...
Page 36
Video Shade: Video shade setting method is the same as the motion detection. Restart timer: Turn on the restart timer and set restart time, then click “Apply”, the camera will follow the settings to scheduled reboot.
5.5.5 Settings System A) Time: Select the NTP server to synchronize the camera with the internet network time, click to “Sync with PC time”. The camera time automatically becomes the time displayed on the computer. B) Initialize: Set the Language (only available in Chinese and English currently), Lenstype, Reboot, Factory default, Backup setting data and system upgrade in this interface.
Page 38
C) Device information: The device information include device ID, device type, network connection and etc.. D) System Log: The system log records all the steps of the device.
Using Video Management software to view multiple cameras at the same time 6.1 Software installation Download from the below link or Mini CD in the Package. Install it on your computer. ( https://yoluke-tech.com --- Left Side: Software of Security Camera -- HiP2P )
6.2 Add Camera A) Open the software, click , to login system, default password: leave it blank. B) Click to Set an Area name (Like: office / home / factory… …), you also can modify and delete Area as picture showing below.
Page 41
C) Click “Search” to find IP Camera in the LAN, Select the camera click “add” to Add camera. D) Double Click camera’s UID to modify camera’s password.
E) Click Back to preview screen, Double-click the camera name in the device list to preview the screen in real time. 6.3 Software Function introduce 6.3.1 Preview interface Area A: Software display area (Preview, Local playback, Remote playback, Map, Settings, Log, Logout user, Exit client).
Page 43
6.3.2 Local playback Click “Local Playback”, Select file, channel, time and date to search for local video files. Double-click file to play video playback! 6.3.3 Remote playback Click “Search” in the bottom Left to get video file. You can select a file to playback.
Page 44
6.3.4 Config 6.3.4.1 Device Management Adding camera. 6.3.4.2 Parameter Setting Including Image, Video, Audio, SD Card, Network, Mobile Detection, input alarm, PTZ, System, Wi-Fi. Setting method is the same as the WEB setting.
Page 45
6.3.4.3 Record management Click the video camera, tick up the video program, drag the mouse in the schedule, and select the storage address. 6.3.4.4 Linkage Alarm Setting the linkage alarm time, Select alarm mode.
Page 46
6.3.4.5 User management Setting P2P client software login password, Add or Modify the password. 6.3.4.6 Other settings Include Time setting, Connection time out settings, Log retention time settings, Capture format settings, Image capture path settings, Software startup settings, single screen number settings, Display mode, Remote playback port settings, etc.
Page 47
6.3.5 Log view Select the log type, time, Click search to view the device operation log! 6.3.6 Log the user Click “OK” to log the user.
Page 48
6.3.7 Exit system Click “OK” to exit the software!
Frequently Asked Questions Q1: Remote viewing, appear pause and delay phenomenon? A:1) Related to network data, it is recommended to adjust the HD mode to Smooth mode when watching, and the video file is still saved in HD mode. 2) Try to reduce the camera stream when view the video, but reducing the stream may affect the quality of the image.
Page 50
Q8:Can't identify the memory card? A:1) Reinsert the SD card into the camera, powered off and restarted camera ! 2) SD card is recommend to use SanDisk, Kingston, Samsung, Toshiba, PNY Bianwei, Lexar brand Q9: Can't the phone search for the camera's own Wi-Fi? A: Press the camera reset button for 5-8 seconds, make the camera reset factory default.
Page 51
Q17: Can't search for the camera IP address in the local area network. A: Our device default IP address network segment 192.168.1.X, you need to modify your network IP address network segment to the same network segment, then use the search tool on the CD to search for IP addresses. Q18: How to make the camera automatically cruise after setting the preset point? A: Preset point 1-16 call command 41, 17-32 Calling Command 42, 65-80 Calling Command 43, 113-128 Calling Command 44, 128-144 Calling Commands 45, 146-160 call command 46, 161-176 Calling Command 47, 177-192...