Application for Model:P1-4X /P2-20X/P3-4X/P14-4X Note: Due to the continuous updating of the products and software, there may be some discrepancy between the operating guide and APP interface. All the instructions are subject to the actual operational interface. If you want to know if you can update the firmware, pls contact our technical support team.
1. Introduction Thanks for buying YoLuke Security IP Camera. This manual describes all the settings, functions, usage, and common problems and solutions for the cameras in detail. This will help you know the camera quickly and easily. If you have any problems with our camera or are confused with the settings, please contact us, and we will provide technical support as soon as possible.
1. Installation 2. SD Card Slot 3. APP Download Download APP“CamHipro”in Google Play or Apple Store, or scan the QR Code to install. Also we would recommend :Tinycam, Ip Pro3, or ISpy. - 6 -...
5.Mobile APP CamHipro Connection 5.1 Connect the Camera by Network cable Install the APP, connect the mobile phone to the WIFI network, enter the APP and click the Add Device button to enter the Add Device interface. Choose different adding methods according to different types of cameras, because common IP cameras cover various adding methods.
Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 5.2 Connect to IP Camera Hot-Spot and then Configure Wi-Fi On your cell phone go to “settings” then select “Wi-Fi”. Your phone should auto search and find the Wi-Fi signal of the camera.
5.3 Add Camera Add your camera to ‘CamHipro’ APP following the steps below. Step 1 Step 2 Step 3 5.4 Wi-Fi Setting Set your camera to the Router’s Wi-Fi, following the steps below: - 9 -...
Step 1 Step 2 Step 3 Step 4 5.5 Connect the Camera by Searching Nearby Devices Connect the camera to the power supply and the camera will start its self-test mode, which A) should take about 15 seconds. When finished, Open the ‘CamHipro’ APP. B)...
5.6 Mobile APP Function Introduction 5.6.1 Micro SD Card Video files playback and download Caution: if you downloaded the recorded video files from a PC, then the files can only be played via Hiplayer. 5.6.2 Local files, device list and add new camera to change the camera Click to view the local file of different cameras.;click...
5.6.3 Pre-set point and auto cruise (For PTZ) Click the camera in real-time monitor -- turn to next page -- preset position Remarks: HD is a higher-definition display effect than SD (recommended to use when the network is go) - 13 -...
Page 14
P-1 then it should be 41, however, for P2 or P14 etc. it may not be 41, therefore if you would like to know all the function commands for the camera, pls contact support via email at: support@yoluke-tech.com - 14 -...
5.6.4 Change password Click “Change Password” to modify the password. Old password: “admin“ It is recommended that you select a new password, and WRITE it down so you don’t forget. 5.6.5 Set factory default settings of the camera 5.6.6 Alarm management and notification Recording and alarm, the default recording is all day;...
5.6.12 Device time setting 5.6.13 SD card setting Note: The files on the SD card cannot be deleted. To keep the playback function consistent, the SD card will automatically overwrite the earliest recording. - 19 -...
6.Computer Browsing Access 6.1 Download Search Tool https://yoluke-tech.com/pages/software-of-security-camera Download Software from the website ( ) or insert the Mini CD into your computer then install the search tool onto your computer. Click “next” to find the IP camera. You can also select Network Card to search for the IP Camera.
6.4 Interface Multiple preview modes. Region A View memory card capacity and date. Click on the capture camera to take the current image. Region B Local manual recording. Video Recording playback: Click playback, select the date and time, select the local playback or SD card playback, search the video files and double click on the file to play.
Adjust the camera rotation speed and preset point settings: Select pre-setting point 1, the camera rotates to the screen position 1 you want to monitor, click on pre-setting to set the preset point. Type 41 in the pre-setting area to call the command of auto cruise. 6.5 Parameter Settings 6.5.1 SettingMedia Video: Set the video format, video coding, resolution, bit rate, max frame rate, key frame interval, bit rate...
Image: Adjust the brightness, saturation, contrast, exposure parameter and set the WDR, AES, and Img mode, Intelligent night mode, IR LED Control, IRCut mode in this interface. (The camera does not support full colour night vision and smart night vision currently.) Audio: Audio type supported G711 / 726 protocol, audio stream selection on/off, audio input type selection, input / output volume adjustment 6.5.2 SettingNetwork...
Page 25
Wireless: Enable Wireless to search and select the wireless network that you want to add, input password. Click the “check” to verify camera is connected to the wireless signal. DDNS: To set up DDNS (Remote access), You need to request a dynamic domain name in order to be able to fill in the username and password which is provided by your Service provider.
Page 26
ONVIF: Set the Server Port, Preview, Time zone Setting, Image Setting, NVC Type in this interface. If you need help, please contact technical support. P2P: Enable this function, you can then watch video in the Mobile App via the add UID Number. - 26 -...
6.5.3 SettingAlarm Audio alarm: Enable this function. The alarm works well however, for P1-5MP module you need to connect a buzzer, or another audible device and & adjust the volume. Motion detection: There are 4 windows selections under Motion Detection. Select different windows to display different window positions.
Page 28
Alarm: Email setting method is the same as Phone APP. Set the FTP server setting and Image capture in this interface. Schedule: Select the time and click on the “Apply”. - 28 -...
6.5.4 Setting Advanced User: To Change password. Auto snap: Time capture, Choose to set the SD card snap interval or FTP snap interval and save route. - 29 -...
Page 30
Timed record: Set the Record files duration, whether to open Record and stream. Email Setting: Here you will use your email settings from your provider. Just fill in the blanks. FTP Setting: - 30 -...
Page 31
Terminal: Set the cruise laps, “select the centered while self-check” on/off, “close the alarm PTZ movement” on/off and “indicator display mode”. 485Set: These cameras can’t support RS485. Multiple settings: In the same LAN, two or more of this series products from our companies, can be displayed on the same page via this Multiple Setting.
Page 32
Video Shade: Video shade setting method is the same as the motion detection. Restart timer: Turn on the restart timer and set restart time, then click “Apply”, the camera will follow the settings to scheduled reboot. - 32 -...
6.5.5 Settings System Time: Select the NTP server to synchronize the camera with the internet network time, click to “Sync with PC time”. The camera time automatically becomes the time displayed on the computer. Initialize: Set the Language (only available in Chinese and English currently), Lens-type, Reboot, Factory default, Backup setting data and system upgrade in this interface.
Device information: The device information includes device ID, device type, network connection etc. System Log: The system log records all the steps of the device. 7.Video Management Software (HIP2P Client) Using Video Management software to view multiple cameras at the same time - 34 -...
7.1Software installation You can download the software from our website (https://yoluke-tech.com) or you can insert the Mini CD which comes in the package into your CD/DVD drive, then Install it on your computer. Note: This program recognises the UID of the camera and not the IP of the camera. The IP of the camera is used for access to the web 7.2 Add Camera...
Page 36
C) Click “Search” to find IP Camera on the LAN, Select the camera click “add” to Add camera. - 36 -...
Page 37
D) Double Click camera’s UID to modify camera’s password. (Applies after a camera is added to the wifi, or after a camera has been connected by a network cable ie: cat5/6. You can access your camera anywhere via the internet.). - 37 -...
Page 38
E) Click To go Back to the preview screen, Double-click the camera name in the device list to preview the screen in real time.(Or right click on the connection as shown by the red arrow) - 38 -...
Frequently Asked Questions Q1: Why does Remote viewing, appear paused or delayed? A:1) This can be Related to network data, it is recommended to adjust the HD mode to Smooth mode when watching, and the video file is still saved in HD mode. 2) Try to reduce the camera stream when viewing the video, reducing the stream may improve the quality of the image.
Page 40
Q4: Camera IP address often changes A:1) Login to web version and go to the camera setting, change the automatic IP address to manual setting. 2) The IP address which automatically obtained will vary depending on the IP address assigned by your router's DHCP.
video playback, recommend to unplug and plug the SD card again. 4) Because the remote playback of the video file is relatively large, Networks do not support remote playback of network traffic! Recommend to connect your phone to a faster Wi-Fi,(if available )then try remote playback. Q15: Can't search for the camera IP address on the local area network.