THUNDER TIGER ER-4 G3 6402-F Instruction Manual & Parts Catalogue page 5

TRANSMITTER CONTROLS
1. Transmitter Antenna: Straighten up the antenna before operating the model.
2. Battery Level Indicator: Three LEDs indicate the battery voltage level. If the Red LED flashes, please replace the batteries.
3. HI/LO Throttle ATV (Adjustable Travel Volume): Allows you to independently preset the maximum travel of the throttle servo either side
(high / low) of neutral.
4. Servo reversing switches: To reverse the servo's rotation direction at the flip of the switch. The reversing switches are recessed into the
transmitter to prevent accidental operation.
5. Steering Trim: To adjust the steering in small increments or decrements to run the model straight.
6. Throttle Trim: To adjust the throttle in small increments or decrements and shift neutral position.
7. Steering D/R (Dual Rates): Push this lever left or right to adjust the amount of the steering dual rate. Right to increase dual rate amount,
and left to decrease amount.
8. AUX Ch Button: Additional function for controlling of the model.
9. External Charging Jack: For rechargeable NiCd/NiMH battery pack (transmitter pack only).
10. 2.4GHz binding SW: The Binding SW button is located on the back of the 2.4GHz transmitter. For additional details, please refer to the
"Binding" setting procedure (Page 5).
11. Steering Wheel: To control the steering of the model.
12. Power Switch: Slide to turn the transmitter on & off.
13. Throttle Trigger: Pull or push to control forward, reverse & speed of the model.
14. Steering Tension Adjustment: Use a Phillip type screwdriver to tighten or loosen the tension of the steering wheel.
15. Battery Cover: Slide cover to install or remove batteries.
發射機各部功能簡介
1. 發射機天線：使用發射機時，請先將發射機天線打直，以增加訊號接收距離。
2. 發射機電源顯示燈：三顆LED設計顯示發射機電池殘量，若紅色LED燈閃爍時，請更換發射機電池。
3. 高、低速油門行程調整鈕：獨立調整高、低速油門行程量功能。
4. 正逆轉設定裝置：位於發射機背面（如圖示），控制伺服機作動方向。
5. 轉向微調鈕：利用此旋鈕，調整設定轉向正確中立點位置。
6. 油門微調鈕：利用此旋鈕，調整設定油門正確中立點位置。
7. 轉向大小動調整鈕：調整轉向伺服機的行程量。
8. 第三動開關：第三動功能開關鈕。
9. 充電孔：使用充電式電池時，可利用此充電孔，進行充電工作。
10. 2.4GHz 校頻配對設定鈕：BINDING SW校頻配對設定鈕為配對發射/接收頻率之用。更多設定請參考說明書第5頁"安全校頻配對步驟"。
11. 轉向舵輪：控制車輛轉向裝置。
12. 電源開關：發射機電源開關。
13. 油門控制板機：控制車輛前進或後退的裝置。
14. 轉向舵輪調整螺絲：使用小型十字起子調整此調整螺絲來改變轉向舵輪旋轉鬆緊度。
15. 電池蓋。
MOTOR
馬達
RECEIVER
ANTENNA
接收機
天線
CH1
SERVO
伺服機
All manuals and user guides at all-guides.com
ESC
速控器
CH2
7.4V POWER BATTER PACK
電池
7.4V POWER BATTER PACK
電池
4.2 MODEL WIRING DIAGRAM 電控系統連結圖
Battery Connector
電池接頭
ON/OFF Switch
速控器開關
To Motor
(Orange/Yellow/Blue)
馬達接頭（橘黃藍）
4
To Receiver (CH2)
接收機 (CH2)
Heat Sink
散熱鰭片