Overload Protection; Overheat Protection; Overdischarge Protection - Makita DVC867L Instruction Manual

NOTE: During the cleaner turned on with the stand-by
switch set to "AUTO", the battery indicator does not
work.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:

Overload protection

When the tool is operated in a manner that causes it to
draw an abnormally high current, the tool automatically
stops without any indication. In this situation, turn the
tool off and stop the application that caused the tool to
become overloaded. Then turn the tool on to restart.

Overheat protection

On
When the tool is overheated, the tool stops automatically, and
the battery indicator blinks about 60 seconds. In this situa-
tion, let the tool cool down before turning the tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops
automatically. If the product does not operate even
when the switches are operated, remove the batteries
from the tool and charge the batteries.
Switch action
► Fig.7: 1. Stand-by switch 2. Power button 3. Suction
force adjusting knob
To start the cleaner:
1. Set the stand-by switch to the "I" side. The cleaner
gets into stand-by state.
2. Press the power button.
To make the cleaner get into stand-by mode, press the
power button again.
To turn off the cleaner, set the stand-by switch to the
"O" side.
The suction power can be adjusted according to your
work need.
Suction power can be increased by turning the suc-
tion force adjusting knob from the
the symbol.
NOTICE:
Always set the stand-by switch to the "O"
side when not using the cleaner for long time. The
cleaner consumes power during stand-by state.
Locking or unlocking the caster
► Fig.8: 1. Caster 2. Stopper lever 3. FREE position
4. LOCK position
Locking the caster is convenient when storing the
cleaner, stopping the work on the way and keeping the
cleaner still.
To operate the stopper, move it by hand.
To lock the caster with a stopper, lower the stopper
lever and the caster no longer will rotate. To release the
caster from the locked position, raise the stopper lever.
NOTE: When moving the cleaner, make sure that
the caster is unlocked. Moving the cleaner with the
caster in the locked position may cause damage to
the caster.
Carriage handle
When carrying the cleaner, carry it by holding the han-
dle on the head. The handle is retractable at the head
when not in use.
► Fig.9
ASSEMBLY
Blinking
switched off and the battery cartridge is removed
before carrying out any work on the tool.
assembly or maintenance.
Installing the powder filter (HEPA)
and prefilter (for dry dust)
uids or wet dusts when using the powder filter.
Picking up such things may cause the powder filter
breakage.
To use powder filter:
1.
mounting position markings.
2.
place them in the prefilter while aligning the mounting
position markings.
3.
► Fig.10: 1. Tank cover 2. Powder filter (HEPA)
NOTICE:
sure that prefilter and damper are used together. It
is not allowed to install powder filter alone.
Installing the paper pack
symbol to
Optional accessory
use the prefilter together that is preinstalled on
the tool. Failure to use the prefilter together may
cause unusual noise and heat, resulting in a fire.
sure that powder filter, damper and prefilter are
always used together.
13 ENGLISH
CAUTION:
Always be sure that the tool is
CAUTION:
Always wear dust mask during
CAUTION:
Never pick up water or other liq-
Place the prefilter in the tank while aligning the
Mount the damper on the powder filter and then
Mount the tank cover and lock it.
3. Damper 4. Prefilter 5. Tank 6. Mounting
position marking
Before using the powder filter, make
WARNING:
When using the paper pack, also
CAUTION:
Before using the paper pack, make