Page 1
O W N E R ' S G U I D E O W N E R S G U I D E M A R V E L O U T D O O R U N D E R C O U N T E R R E F R I G E R AT I O N M A R V E L O U T D O O R U N D E R C O U N T E R R E F R I G E R A T I O N F O R M O D E L # M O R E 2 2 4 F O R M O D E L # M O K R 2 2 4...
Page 2
Got a Marvelous Design? The service number and serial number can be found on the We would love to see how your Marvel product looks in its serial plate which is located inside the cabinet on the left new home. Send us photos at marketing@marvelrefrigera- side near the top.
TABLE OF CONTENTS Tip: Click on any section below to jump directly there Safety Important Safety Instructions Installation Unpacking Your Appliance Electrical Maintenance Stainless Steel Maintenance Operating Instructions Using Your Beverage Dispenser Energy Savng Tips Service Obtaining Service Product Liability Warranty Claims Ordering Replacement Parts R600a Specifications...
IMPORTANT SAFETY INSTRUCTIONS Important Safety Instructions Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situa- tions that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operat- ing this appliance.
UNPACKING YOUR APPLIANCE CAUTION WARNING If the appliance was shipped, handled, or stored in other EXCESSIVE WEIGHT HAZARD than an upright position for any period of time, allow the ap- Use two or more people to move product. pliance to sit upright for a period of at least 24 hours before Failure to do so can result in personal injury.
ELECTRICAL Electrical Connection A grounded 115 volt, 15 amp dedicated circuit is required. This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accor- dance with the National Electrical Code and applicable lo- Do not remove cal codes and ordinances (see Figure 4).
Page 7
USING YOUR BEER DISPENSER Shelving If you are using a quarter barrel of beer, you can add shelf space for keeping your mugs chilled. The quarter barrel the upper and the lower shelf positions. Remove them from the refrigerator and arrange them as follows when setting up your unit.
Page 8
USING YOUR BEER DISPENSER Tools required for installation: This beer dispensing unit will support one half ( or one quarter ( Flat bladed screwdriver support two sixth ( Phillips screwdriver quantity of beer in each barrel size. Pliers Adjustable wrench or a 1 "...
Page 9
USING YOUR BEER DISPENSER Single Dispense Tower Kit Double Dispense Tower Kit Connect ,etc..Connect ,etc..Double Single Dispense Hose clamps Dispense Tower use for connections Tower Hose clamps use for connections Coupler Coupler Coupler Regulator 5 Pound with red Tank airline 5 Pound...
Page 10
USING YOUR BEER DISPENSER Rear of counter top If you are installing your keg refrigerator under a coun- ter you will need to drill 5 holes in the counter top to " " diameter hole located at the center of the tower for the beer line, lo- typical cate approximately 13 Diameter...
Page 11
USING YOUR BEER DISPENSER 9. Hooking up the keg coupler to the keg: Verify the cou- lugs on the keg with the corresponding openings on the keg coupler Connect and turn clockwise until the coupler stops with "S" clockwise to hook allow gas to enter the keg.
Page 12
USING YOUR BEER DISPENSER Optional CO tank external mounting bracket: CAUTION The optional mounting bracket is designed to hold the 5# cylinder that comes with the beer dispenser. Larger cylinders may be purchased from a third party and mounted If the CO externally.
Page 13
USING YOUR BEER DISPENSER Regulator (Double Dispense Tower) Regulator (Single Dispense Tower) Your beer dispenser comes equipped with a 5 pound CO Your beer dispenser comes equipped with a 5 pound CO tank and a dual gauge regulator. The lower gauge should tank and a single gauge regulator.
Page 14
Clean the sump area with soapy On a built in beer dispenser remove the Marvel grate and counter top sump, clean with soap and water and dry Marvel grate before reinstalling.
STAINLESS STEEL MAINTENANCE Background NOTE Stainless steel does not stain, corrode, or rust as easily as ordinary steel, but it is not stain or corrosion proof. Stain- less steels can discolor or corrode if not maintained prop- Stainless steel products should never be installed, or stored erly.
ENERGY SAVING TIPS The following suggestions will minimize the cost of operating your refrigeration appliance. 1. Do not install your appliance next to a hot appliance (cooker, dishwasher, etc.), heating air duct, or other heat sources. 2. Install product out of direct sunlight. 3.
OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please contact your dealer or call Marvel Customer Service at 616.754.5601 for directions on how to obtain warranty coverage in your area. •...
The part that caused the damage must be returned to Marvel in its entirety. The part must be clearly labeled with the serial number of the unit it was removed from, the date, and the servicer who removed the part.
Claims must be submitted online at • Final billing - Remodel www. marvelservice . co m Warranty parts will be shipped at no charge after Marvel • 60 day submittal d eadline from date of completed confirms warranty status. Please provide the model, serial service number, part number and part d escription.
Warranty parts will be shipped at no charge after Marvel confirms warranty status. Please provide the model, serial number, part number and part description. Some parts will require color or voltage information.
PERSONNEL DO HOT PUNCTURE REFRIGERANT TUBING refrigeration system. RISK Of FIRE OR EXPLOSION. FIAMHA_ B LE REFRIGERANT USED. CONSULT Never substitute Marvel OEM replacement parts REPAIR IIANUAVOWHER'S GUIDE BEFORE ATTEMPTING TO SERVICE THIS PRODUCT. ALL SAFETY PRECAUTIONS HUST BE FOUOWEO.
Page 22
R-600A SPECIFICATIONS/LABELING WARNING R-600a equipped products are labeled (both the unit and the compressor). Only skilled and well trained service technicians permitted to service R-600a equipped products. R-600a is colorless and odorless. All tools and equipment must be approved for use with R-600a refrigerant.
Page 23
Evacuate/reclaim via the piecing pliers to ensure the When re-brazing, the system must be purged with dry system is empty of R-600a before any system work is nitrogen and at least one access point open to the performed. atmosphere. When re-brazing, proper ventilation is required along with constant monitoring for the presence of R600a refrigerant.
Page 24
The low side of the refrigeration system (evaporator, Proper ventilation during service is required. compressor and suction line) must be leak tested with the compressor off (equalized pressure). Never apply a torch to a charged R-600a refrigeration system. RECHARGING No air is ever to be allowed inside the refrigeration system Use OEM replacement service parts and do not alter the (R-600a refrigerant or dry nitrogen only).
System Diagnosis Guide REGRIGERATION SYSTEM DIAGNOSIS GUIDE System Suction Suction Compressor Condenser Capillary Evaporator Wattage Condition Pressure Line Discharge Tube Normal Normal Slightly Very hot Very hot Warm Cold Normal below room temperature Overcharge Higher than Very cold Slightly warm Hot to warm Cool Cold...
Page 26
For designated Marvel Professional product, Marvel offers a one year extension of the two year warranty coverage from the date of purchase, free of charge. To take advantage of this third year warranty, you must register your product with Marvel within 60 days from the date of purchase at marvelrefrigeration.com and provide proof of purchase.
Page 27
Marvel Refrigeration 1260 E. Van Deinse St. 616.754.5601 41015651 Rev A 11/1/20 the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
Need help?
Do you have a question about the MOKR224 and is the answer not in the manual?
Questions and answers