Nokia 3155 Reassembly
Mobile terminal
Hide thumbs
Also See for 3155:
- User manual (201 pages) ,
- Rf description and troubleshooting (68 pages) ,
- Service tools (22 pages)
Related Manuals for Nokia 3155
Summary of Contents for Nokia 3155
- Page 1 Nokia Customer Care 3155/3155i (RM-41), 3152 (RM-61) Mobile Terminal Reassembly ©2005 Nokia Corporation ISSUE 1 07/2005 Company Confidential...
-
Page 2: Table Of Contents
3155/3155i (RM-41), 3152 (RM-61) Reassembly Contents Page Safety Information ............................3 ESD Protection ............................. 3 Reassembly Instructions ..........................4 1. Attach the TX Compression Gasket ....................4 2. Insert the D-cover UIM Card Trap ...................... 4 3. Attach the Whip Antenna ........................5 4. -
Page 3: Safety Information
• Every repair action involving opening the phone or handling the phone components must be done under ESD protection. • ESD-protected spare part packages MUST NOT be opened/closed outside an EPA. For more detailed information about ESD protection and EPAs, contact your local Nokia Customer Care representative. ©2005 Nokia Corporation... -
Page 4: Reassembly Instructions
3155/3155i (RM-41), 3152 (RM-61) Reassembly Reassembly Instructions 1. Attach the TX Compression Gasket A TX compression gasket is needed only if a new unassembled D-cover is used. Stick the TX compression gasket to the unassembled D-cover. 2. Insert the D-cover UIM Card Trap a. -
Page 5: Attach The Whip Antenna
3155/3155i (RM-41), 3152 (RM-61) Nokia Customer Care Reassembly 3. Attach the Whip Antenna Attach the whip antenna into the D-cover by pushing down in the direction of the arrow. 4. Insert the Volume Key Insert the volume key into the notch in the D-cover. -
Page 6: Insert The Dc Jack And Microphone
3155/3155i (RM-41), 3152 (RM-61) Reassembly 6. Insert the DC Jack and Microphone Use tweezers to insert the DC jack and microphone into the D-cover. Ensure that you do not touch the electrical connectors on the top of each part. Microphone DC jack 7. -
Page 7: Insert The Led Light Guide
3155/3155i (RM-41), 3152 (RM-61) Nokia Customer Care Reassembly 8. Insert the LED Light Guide Use tweezers to push the LED light guide into the hinge assembly of the C-cover. LED light guide 9. Assemble the Engine PWB and the C-cover Insert the PWB by aligning it using the screw holes and C-cover clasp and snapping it into place. -
Page 8: Connect The C-Cover And The D-Cover
3155/3155i (RM-41), 3152 (RM-61) Reassembly 11. Connect the C-cover and the D-cover a. Align the screw holes and combine the D-cover and C-cover. b. Engage snaps of the covers at the locking locations shown in following order: • 1. side snap near volume key •... -
Page 9: Add The Screws
3155/3155i (RM-41), 3152 (RM-61) Nokia Customer Care Reassembly 12. Add the Screws Add the four black screws in a clockwise order as shown. Use torque driver set to 18Ncm. 13. Add the Keymat Insert the top edge of the keymat first. Then bend the keymat to insert the bottom edge. -
Page 10: Attach The Main Lcd Display Into The B-Cover
3155/3155i (RM-41), 3152 (RM-61) Reassembly 14. Attach the Main LCD Display into the B-cover For a brand new, unassembled LCD display module, follow the steps below: a. Using tweezers, peel back the tape. Peel open the flex cable next. b. Carefully replace tape and wrap the flex cable around. -
Page 11: Attach Earpiece And Acoustic Vent To The B-Cover
3155/3155i (RM-41), 3152 (RM-61) Nokia Customer Care Reassembly 15. Attach Earpiece and Acoustic Vent to the B-cover When assembling a brand new unassembled earpiece or changing the earpiece, follow the steps below: • Remove old earpiece and acoustic vent. • Attach new adhesive acoustic vent to B-cover •... -
Page 12: Attach The Main Display Flex Cable To The Ui Pwb
3155/3155i (RM-41), 3152 (RM-61) Reassembly 17. Attach the Main Display Flex Cable to the UI PWB Attach the LCD flex connector. Main display flex cable 18. Attach the Secondary LCD Display Flex Cable Secondary Display Flex cable 19. Attach the Display Frame Place the display frame into the slot near the hinge, then rotate downward over the LCD display. -
Page 13: Add The Screws To The A-Cover
3155/3155i (RM-41), 3152 (RM-61) Nokia Customer Care Reassembly 20. Add the Screws to the A-cover Add the four silver screws in the order shown below. Use torque driver set to 18Ncm. 21. Attach the A-cover a. Starting with one side, attach the A-cover bottom snaps into the B-cover hooks. -
Page 14: Insert The Battery And Attach The Battery Cover (E-Cover)
3155/3155i (RM-41), 3152 (RM-61) Reassembly 22. Insert the Battery and Attach the Battery Cover (E-cover) a. Insert the battery. b. Align E-cover tabs with the slots, and slide it towards the top while pressing down until you feel it click into place.