1. Manuals
  2. Brands
  3. ARH Manuals
  4. Digital Camera
  5. SmartCAM
  6. Install manual

ARH SmartCAM Install Manual

Intelligent all-in-one lpr camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Page 1/14
SmartCAM Install Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SmartCAM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ARH SmartCAM

Summary of Contents for ARH SmartCAM

  • Page 1 Page 1/14 SmartCAM Install Guide...

  • Page 2: Table Of Contents

    2. BRACKET DETAILS AND SIZES ..........................4 CABLE LAYOUTS ................................... 5 SOFTWARE REQUIREMENTS ............................7 ACCESSING THE CAMERA ............................... 8 RECOMMENDED CAMERA POSITION ........................9 MAINTENANCE / STORAGE ............................11 PC RECOVERY MODE ..............................12 APPENDIX....................................13 CONTACT INFORMATION ............................. 14 Page 2/14 SmartCAM Install Guide...

  • Page 3: Install The Hardware

    1. Loosen the camera fastening screw on the bottom of the bracket. (Use size 5 Allen key). 2. Adjust the bracket into the desired position. 3. Tighten the screw back. Do not overtighten the screws. Page 3/14 SmartCAM Install Guide...

  • Page 4: Mounting

    1. MOUNTING The bracket can be mounted onto different surfaces. Use appropriate screws for installation according to the mountable surface. Failures due to inappropriate installation void the warranty. 2. BRACKET DETAILS AND SIZES Page 4/14 SmartCAM Install Guide...

  • Page 5: Cable Layouts

    ETHERNET SPECIFICATION: CAT5e crossover cable with RJ45 plug. The layout of the upper user I/O connector is the following: INDICATION USER I/O CABLE FRONT VIEW (CAMERA CONNECTOR SIDE) OPTO1_IN_S OPTO1_IN_G OPTO1_OUT_S OPTO1_OUT_G OPTO2_IN_S OPTO2_IN_G OPTO2_OUT_S OPTO2_OUT_G RB_USER TA_USER GND_USER Page 5/14 SmartCAM Install Guide...
  • Page 6 (max. 2.5A transients occur for a few msecs) (WITHOUT HEATING) OVER-CURRENT by fuse PROTECTION TRIGGER SPECIFICATIONS:  Input: min. 5V, max. 12V Logic Output: min. 5V, max. 12V, max. 10mA  Pulse width: min. 1 ms Be aware of the polarity Page 6/14 SmartCAM Install Guide...

  • Page 7: Software Requirements

    SOFTWARE REQUIREMENTS The SmartCAM is developed to operate without any kind of special software. SOFTWARE REQUIREMENTS:  For network setup, administrator (root) privileges are necessary.  Web browser: Mozilla Firefox 47, Internet Explorer 10-11, Google Chrome 51 or later editions. If it is possible, update your browser (Firefox or Chrome) to the newest available version.

  • Page 8: Accessing The Camera

    5. Start a browser then enter the default IP address of the camera into the address bar (http://192.168.1.4). After this, the camera starts with administrator privileges, ready to be set up and configured. Page 8/14 SmartCAM Install Guide...

  • Page 9: Recommended Camera Position

    English characters). The too large characters are also not suitable for ANPR, therefore try to avoid settings where the character size is greater than 50 pixels in height. A line width of a character on the image should be at least 2 pixels. Page 9/14 SmartCAM Install Guide...
  • Page 10 A properly set camera should provide a similar image: A proper sample image Proper character sizes (in pixels) on the sample image Page 10/14 SmartCAM Install Guide...

  • Page 11: Maintenance / Storage

    LED’s. Do not look into the illumination unit directly from close range or for more than 100 seconds. If you do not take these safety precautions, you risk damaging your eyes. Page 11/14 SmartCAM Install Guide...

  • Page 12: Pc Recovery Mode

    After this process, the following window will appear on your browser: After clicking the [Restore Factory State] button on the bottom left side of the window, the PC will return with the factory settings in a few seconds. Page 12/14 SmartCAM Install Guide...

  • Page 13: Appendix

    2. Enter the ifconfig command to see the reserved Ethernets (e.g. eth0). 3. Enter the following command: ifconfig ethY 192.168.1.25 where Y is a free eth (e.g. eth1) and 192.168.1.25 is a sample IP address. Page 13/14 SmartCAM Install Guide...

  • Page 14: Contact Information

    Web: www.adaptiverecognition.com ARH Technical Support System (ATSS) is designed to provide you the fastest and most proficient assistance, so you can quickly get back to business. Information regarding hardware, software, manuals and FAQ are easily accessible for customers who previously registered to enter the dedicated ATSS site. Besides offering assistance, the site is also designed to provide maximum protection while managing your business information and technical solutions utilized.

Table of Contents